• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1584-1586
• /
• 2002

CuIn$Se_2$ (CIS) and related compounds such as Cu($In_xGa_{1-x})Se_2$(CIGS) have been studied by their potential for use in photovoltaic devices. CIS thin film materials which have high absorption coefficient and wide bandgap, have attracted much attention as an alternative to crystalline and amorphous silicon solar cells currently in use. Cu-rich CIGS film have very low resistivity, due to coexistence of the semimetallic $Cu_{2-x}Se$. In-rich CIGS films show high resistivity, since these films are compensated films without the $Cu_{2-x}Se$ phase. Optical properties of the CIGS films also change in accordance with the resistivity for the Cu/(In+Ga) ratio. The Cu-rich films have different spectra from In-rich films in near infrared wavelengths.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.781-787
• /
• 1996

Silicom oxide films with good water repellency were prepared by rf plasma-enhanced CVD (rf-PECVD) using four kinds of organosilicon compound, which had different number of methyl ($CH_3$) groups, and oxygen as gas sources. The differences in the deposition rates, film composition and film properties were studied in detail. Water repellency depended on the number of $CH_3$ groups in the organosilicon compounds and the partial pressure of oxygen in the plasma. The highest contact angle for water drops, about 95 degrees, was obtained when trimethy lmethoxy silane (TMMOS) was used. The contact angle decreased with the amount of oxygen gas introduced into the plasma. The dissociation of $CH_3$ groups by adding oxygen was comfirmed by Fourier transform infrared spectroscopy(FTIR) and X-ray photoelectron spectroscopy (XPS). The optical properties were estimated by double-beam spectroscopy and ellipsometry. The transmittance of the glass plate coated by the film prepared with tetramethoxy silane (TMOS) was about 90% and the refractive index of film was 1.44. This value was smaller than the refractive index of a glass plate(soda lime glass, refractive index is 1.515) and this film played a role of anti-refractive coating.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.87-95
• /
• 2017

Lithium silicate, a lithium-ion conducting ceramic, is coated on a layer-structured lithium nickel manganese oxide ($LiNi_{0.7}Mn_{0.3}O_2$). Residual lithium compounds ($Li_2CO_3$ and LiOH) on the surface of the cathode material and $SiO_2$ derived from tetraethylorthosilicate are used as lithium and silicon sources, respectively. Powder X-ray diffraction and scanning electron microscopy with energy-dispersive spectroscopy analyses show that lithium silicate is coated uniformly on the cathode particles. Charge and discharge tests of the samples show that the coating can enhance the rate capability and cycle life performance. The improvements are attributed to the reduced interfacial resistance originating from suppression of solid-electrolyte interface (SEI) formation and dissolution of Ni and Mn due to the coating. An X-ray photoelectron spectroscopy study of the cycled electrodes shows that nickel oxide and manganese oxide particles are formed on the surface of the electrode and that greater decomposition of the electrolyte occurs for the bare sample, which confirms the assumption that SEI formation and Ni and Mn dissolution can be reduced using the coating process.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.1-4
• /
• 2000

Thin films of hydrogenated amorphous silicon carbide compounds ($a-Si_{x}C_{1-x}:H$) of different compositions were deposited on Si substrate by RF plasma-enhanced chemical vapor deposition (PECVD). Experiments were carried out using silane (SiH$_4$) and methane ($CH_4$) as the gas precursors at 1 Torr and at a low substrate temperature ($250^{\circ}C$). The gas flow rate was changed with the other parameters (pressure, temperature, RF power) fixed. The substrate was Si(100) wafer and all of the films obtained were amorphous. The bonding structure of $a-Si_{x}C_{1-x}:H$films deposited was investigated by X-ray photoelectron spectroscopy (XPS) for the film compositions. In addition, the surface morphology of films was investigated by atomic force microscopy (AFM).

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.130-136
• /
• 2008

$xTiO_2$-$ySiO_2$ system photocatalysts were developed by sol-gel method based on the change of production parameters, and their structure of crystallization and the specific surface area were measured. Considering the efficiency of the ethanol and phenol degradation using the catalyst, the conclusions were obtained as follows: By means of X-ray analysis of $xTiO_2$-$ySiO_2$ powder that is obtained from Titanium and Silicon alkoxide by sol-gel process, it is shown that crystal structure of anatase type is a dominating structure and, on the other hand, the structure of rutile also partly exists. The increase of $SiO_2$ contents causes the decrease of the degree of crystallization of the gel, whereas the specific surface area preferentially increases. It is shown that more than 90% of ethanol and phenol are degraded when reaction time is about three and an hours, and the maximum degradation rate of ethanol and phenol is shown in $60TiO_2$-$40SiO_2$ catalyst.

• Bulletin of the Korean Chemical Society
• /
• v.8 no.4
• /
• pp.242-246
• /
• 1987

The hydrogen abstraction reactions of $SiH_4, SiH_2Cl_2 \;and\; SiHCl_3$ by ground state chlorine atoms generated photochemically from chlorine molecules have been studied at temperatures between 15 and $100^{\circ}C.$ The absolute rates for the reactions have been obtained by a competition technique using ethane as a competitor. The rate expressions ($in cm^3/mol/s$) are found to conform to an Arrhenius rate law: $k_{SiH_4} = (7.98 {\pm} 0.42) {\times} 10^{13}$ exp $[-(1250 {\pm}20)/T].$ $k_{SiH_2Cl_2} = (2.25 {\pm} 0.12) {\times} 10^{15}$ exp[-(1010 ${\pm}$ 10)/T]. $k_{SiHCl_3} = (9.04 {\pm} 0.28) {\times} 10^{14}\; exp[-(1200 {\pm} 10)/T].$ The activation energies obtained from this study represent the same trend as with the carbon analogues, while this trend was not found with respect to the bond dissociation energies among silicon compound homologues. These anomalous behaviors were interpreted in terms of electronic effects and of the structural differences between these compounds.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.2
• /
• pp.154-161
• /
• 1994

Studies have been conducted to explore single electron transfer (SET) induced photocyclization reactions of N-(trimethylsilylmethylthioalkyl)phthalimides (alkyl=ethyl, n-propyl, n-butyl, n-pentyl, and n-hexyl). Photocyclizations occur in methanol in modest to high yields to produce cyclized products in which phthalimide carbonyl carbon is bonded to the carbon of side chain in place of the trimethylsilyl group. Mechanism for these photocyclizations involving intramolecular SET from sulfur in the ${\alpha}$-silylmethylthioalkyl groups to the singlet excited state phthalimide moieties followed by desilylation of the intermediate ${\alpha}$ -silylmethylthio cation radicals and cyclization by radical coupling is proposed. In contrast, photoreactions of N-(trimethylsilylmethylthioalkyl)phthalimides in acetone follow different reaction routes to produce another cyclized products in which carbon-carbon bond formation takes place between the phthalimide carbonyl carbon and the carbon ${\alpha}$ to silicon and sulfur atoms via triplet carbonyl hydrogen abstraction pathway. The normal singlet SET pathway dominates this triplet process for photoreactions of these substances in methanol while the triplet process dominates the singlet SET pathway for those in acetone. The efficient and regioselective cyclization reactions observed for photolyses in methanol represent synthetically useful processes for construction of medium and large ring heterocyclic compounds.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.2
• /
• pp.166-172
• /
• 1992

Studies have been conducted to explore single electron transfer (SET) induced photocyclization reactions of N-(trimethylsilylmethoxyalkyl)phthalimides(alkyl=E thyl, n-propyl, n-butyl, n-pentyl, and n-octyl). Photocyclizations occur in methanol in high yields to produce cyclized products in which phthalimide carbonyl carbon is bonded to the carbon of side chain in place of the trimethylsilyl group. Mechanism for these photocyclizations involving intramolecular SET from oxygen in the $\alpha-silylmethoxy$ groups to the singlet excited state phthalimide moieties followed by desilylation of the intermediate $\alpha-silylmethoxy$ cation radicals and cyclization by radical coupling are proposed. In contrast, photoreaction of N-(trimethylsilylmethoxyethyl) phthalimide in acetone follows different reaction routes to produce two cyclized products in which carbon-carbon bond formation takes place between the phthalimide carbonyl carbon and the carbon $\alpha$ to silicon and oxygen atoms via triplet carbonyl hydrogen abstraction triplet carbonyl silyl group abstraction pathways. The normal singlet SET pathway dominates these triplet processes for photoreaction of this substance in methanol. The efficient and regioselective cyclization reactions observed for photolysis in methanol represent synthetically useful processes for construction of medium and large ring heterocyclic compounds.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.32 no.3 s.58
• /
• pp.141-148
• /
• 2006

This study is intended to analyze the impact of PMMA on color changes comparatively by making 2 types of cheek color items with red-color pigments: one containing PMMA, which is one of the recently developed circular polymers and used when producing color make-up items that have aero powder as the chief ingredient, and the other without it. To accomplish the purpose, we have reviewed literature on raw materials that have aero powder as the chief ingredient. Also, after making compounds of PMMA and pigments lot aero powder, such as Talc, Mica, OMC Talc As, Mica As, we examined them compared to those without PMMA using spectrophotometer, a questionnaire survey, and Digital camera. Besides, the particles were analyzed using SEM. As a result of the analysis, cosmetics containing PMMA represent more vivid and rich colors, putting on one's face softly. Since the entire specific surface area of PMMA is large enough to absorb oil evenly, it yields vivid and rich colors. But, Mica, one of natural pigments, shows a result as opposed to that of Mica As, one of silicon-compounded pigments, suggesting that pearl effect may possibly causes defused reflection. Based on these findings, it is expected that cosmetics will have more vivid colors, or improved color presentation, as well as the softer sense of touch when a circular polymer of PMMa is added to the manufacturing process of color make-up items.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.161-163
• /
• 2002

The BNCT(Boron Neutron Capture Therapy) facility has been developed in Hanaro(High-flux Advanced Neutron Application Reactor), a research reactor of Korea Atomic Energy Research Institute. A typical tangenial beam port is utilized with this BNCT facility. Thermal neutrons can be penetrated within the limits of the possible maximum instead of being filtered fast neutrons and gamma rays as much as possible using the silicon and bismuth single crystals. In addition to, the liquid nitrogen (LN$_2$) is used to cool down the silicon and bismuth single crystals for the increase of the penetrated thermal neutron flux. Neutron beams for BNCT are shielded using the water shutter. The water shutter was designed and manufactured not to interfere with any other subsystem of Hanaro when the BNCT facility is operated. Also, it is replaced with conventional beam port plug in order to cut off helium gas leakage in the beam port. A circular collimator, composed of $\^$6/Li$_2$CO$_3$ and polyethylene compounds, is installed at the irradiation position. The measured neutron flux with 24 MW reactor power using the Au-198 activation analysis method is 8.3${\times}$10$\^$8/ n/cm$^2$ s at the collimator, exit point of neutron beams. Flatness of neutron beams is proven to ${\pm}$ 6.8% at 97 mm collimator. According to the result of acceptance tests of the water shutter, the filling time of water is about 190 seconds and drainage time of it is about 270 seconds. The radiation leakages in the irradiation room are analyzed to near the background level for neutron and 12 mSv/hr in the maximum for gamma by using BF$_3$ proportional counter and GM counter respectively. Therefore, it is verified that the neutron beams from BNCT facility in Hanaro will be enough to utilize for the purpose of clinical and pre-clinical experiment.