• 제목/요약/키워드: Silica($SiO_2$)

검색결과 665건 처리시간 0.032초

FHD법에 의해 증착된 실리카막의 도펀트 첨가에 의한 굴절률 제어 (Refractive Index Control by Dopant for Thick Silica films Deposited by FHD)

  • 김용탁;서용곤;윤형도;임영민;윤대호
    • 한국세라믹학회지
    • /
    • 제40권6호
    • /
    • pp.589-593
    • /
    • 2003
  • 실리카 평판광회로는 다양한 광수동소자에 응용이 되고 있으며, 이를 구성하는 SiO$_2$와 GeO$_2$-SiO$_2$ 막은 화염가수분해증착에 의해 증착되었다. SiO$_2$ 막은 산-수소 토치에 SiCl$_4$, POC1$_3$와 BCl$_3$를 주입하여 화염가수반응에 의해 생성되었으며, POC1$_3$/BC1$_3$ 유량비가 증가함에 따라 P 농도는 2.0-2.8 at%까지 증가하였고, 굴절률은 1.4584-1.4605로 증가하였다. GeO$_2$-SiO$_2$ 막의 굴절률은 GeCl$_4$ 유량에 의해 제어되었으며 30-120 sccm으로 증가함에 따라 1.4615-1.4809로 증가하였다.

Metal effects in Mn-Na2WO4/SiO2 upon the conversion of methane to higher hydrocarbons

  • Tang, Liangguang;Choi, Jonghyun;Lee, Woo Jin;Patel, Jim;Chiang, Ken
    • Advances in Energy Research
    • /
    • 제5권1호
    • /
    • pp.13-29
    • /
    • 2017
  • The roles of Na, Mn, W and silica, and the synergistic effects between each metal in the $MnNa_2WO_4/SiO_2$ catalyst have been investigated for oxidative coupling of methane (OCM). The crystallisation of amorphous silica during calcination at $900^{\circ}C$ was promoted primarily by Na, but Mn and W also facilitated this process. The interaction between Na and Mn tended to increase the extent of conversion of $Mn_3O_4$ to $Mn_2O_3$. The formation of $Na_2WO_4$ was dependent on the order in which Na and W were introduced to the catalyst. The impregnation of W before Na resulted in the formation of $Na_2WO_4$, but this did not occur when the impregnation order was reversed. $MnWO_4$ formed in all cases where Mn and W were introduced into the silica support, regardless of the impregnation order; however, the formation of $MnWO_4$ was inhibited in the presence of Na. Of the prepared samples in which a single metal oxide was introduced to silica, only $Mn/SiO_2$ showed OCM activity with significant oxygen conversion, thus demonstrating the important role that Mn plays in promoting oxygen transfer in the reaction. The impregnation order of W and Na is critical for catalyst performance. The active site, which involves a combination of Na-Si-W-O, can be formed in situ when distorted $WO_4^{2-}$ interacts with silica during the crystallisation process facilitated by Na. This can only occur if the impregnation of W occurs before Na addition, or if the two components are introduced simultaneously.

Influence of $TiO_2$ Thin Film Thickness and Humidity on Toluene Adsorption and Desorption Behavior of Nanoporous $TiO_2/SiO_2$ Prepared by Atomic Layer Deposition (ALD)

  • Sim, Chae-Won;Seo, Hyun-Ook;Kim, Kwang-Dae;Park, Eun-Ji;Kim, Young-Dok;Lim, Dong-Chan
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
    • /
    • pp.268-268
    • /
    • 2012
  • Adsorption and desorption of toluene from bare and $TiO_2$-coated silica with a mean pore size of 15 nm was studied using breakthrough curves and temperature programmed desorption. Thicknesses of $TiO_2$ films prepared by atomic layer deposition on silica were < 2 nm, and ~ 5 nm, respectively. For toluene adsorption, both dry and humid conditions were used. $TiO_2$-thin film significantly improved toluene adsorption capacity of silica under dry condition, whereas desorption of toluene from the surface as a consequence of displacement by water vapor was more pronounced for $TiO_2$-coated samples with respect to the result of bare ones. In the TPD experiments, silica with a thinner $TiO_2$ film (thickness < 2 nm) showed the highest reactivity for toluene oxidation to $CO_2$ in the absence and presence of water. We show that the toluene adsorption and oxidation reactivity of silica can be controlled by varying thickness of $TiO_2$ thin films.

  • PDF

실리카 지지 니켈-구리 합금에서 일산화탄소의 흡착에 관한 IRS 연구 (An IRS Study on the Adsorption of Carbonmonoxide on Silica Supported Ni-Cu Alloys)

  • 안정수;윤구식;박상윤;박성균
    • 대한화학회지
    • /
    • 제53권3호
    • /
    • pp.233-243
    • /
    • 2009
  • 실리카지지 니켈(Ni-Si$O_2$), 실리카지지 구리(Cu-Si$O_2$), 몇가지 조성의 실리카지지 니켈과 구리의 합금(Ni/Cu-Si$O_2$)을 실온에서 일산화탄소(CO)의 압력을 넓은 범위에서 변화시키면서(0.2 $torr{\sim}$50 torr) 흡착된 CO의 적외선 스펙트럼을 1500 $cm^{-1}{\sim}2500\;cm^{-1}$ 범위에서 관찰했고 실온에서 진공탈착시키면서 흡착된 CO의 적외선 스펙트럼을 관찰했다. Ni-Si$O_2$에 CO를 흡착시켰을 때 2059.6 $cm^{-1},\;{\sim}$2036.5 $cm^{-1},\;{\sim}$1868.7 $cm^{-1},\;{\sim}$1697.1 $cm^{-1}$의 네 흡수띠가 관찰되었고, Cu-Si$O_2$에 일산화탄소를 흡착시켰을 때 $\sim$2115.5 $cm^{-1},\;{\sim}$1743.0 $cm^{-1}$ 두 흡수띠가 관찰되었으며, Ni/Cu-Si$O_2$에서는 ${\sim}2123.2\;cm^{-1}$, 2059.6 $cm^{-1},\;{\sim}$2036.4 $cm^{-1},\;{\sim}$1899.5 $cm^{-1},\;{\sim}$1697.1 $cm^{-1}$에 다섯 흡수띠가 관찰되었다. Ni/Cu-Si$O_2$, Cu-Si$O_2$, Ni/Cu-Si$O_2$에서 CO를 흡착시켰을 때 관찰된 흡수스펙트럼은 이전의 보고와 근사적으로 일치한다. 1800 $cm^{-1}$ 이하의 흡수띠는 Ni이나 Ni/Cu 합금의 스텦이 있는 결정표면에서 관찰된 바 있는데 Ni-Si$O_2$, Ni/Cu-Si$O_2$를 실온에서 CO를 흡착시켰을 때 나타나는 ${\sim}1697.1\;cm^{-1}$ 흡수띠는 Ni이나 Ni/Cu 합금 표면에서 스텦에 인접한 흡착자리에 흡착한 CO에 기인한 흡수띠로 제시할 수 있다. Cu-Si$O_2$ 시료를 실온에서 CO를 흡착시켰을 때 Cu 결정표면에서 2000 $cm^{-1}$ 이하의 흡수띠가 관찰되는 경우는 드문데 1743.0 $cm^{-1}$ 흡수띠는 Cu 표면의 스텦에 인접한 흡착자리에 흡착한 CO에 기인한 흡수띠로 제시할 수 있다. Ni/Cu-Si$O_2$에서 Cu의 함량이 몰분율 0.5까지 변함에 따라 같은 CO 압력 또는 같은 진공탈착시간에서 흡수띠의 위치가 21 $cm^{-1}$ 이하로 다른 ⅠB 금속을 첨가했을 때보다 작게 변하는데 Cu d 전자의 리간드 효과가 작은 현상에 기인한 것으로 볼 수 있다.

1980 냉해조건하 영남지방의 수도임실장해와 규산 및 인산 흡수관계 (Investigation on Uptake of Silica and Phosphorus and Rice Fertilization Impediment Occured in Yeongnam Area under the Cool Weather of 1980)

  • 강양순;정연태;박래경
    • 한국작물학회지
    • /
    • 제26권3호
    • /
    • pp.226-232
    • /
    • 1981
  • 냉온하(7~9월)에서 생육한 수도에 대한 재배수건별(표고별, 품종별) 냉해와 도체경엽중 유효규산 및 인산함량과의 관계를 밝히고져 경남북 일도에 걸처 냉해실태를 조사하여 분석해 본 결과는 다음과 같다. 1. 임실비율은 표고가 높아질수록 떨어졌으며 통일계품종에서 더욱 현저하였다. 2. 임실비율 증가에 따라 토양중 $SiO_2/P_2 O_5$ 함량비는 낮아졌고 도체경엽중에서는 높아졌다. 3. 규산이 인산함량에 비하여 도체의 경엽중에서는 10.5\sim20.5배 정도 토양중에는 0.28~0.78배로 함유되어 있었다. 4. 임실비율과 도체경엽중 $SiO_2/P_2 O_5$함량비와는 정의 유의상관이 인정되었다. 5. 식물체중 규산함량 증가에 따른 임실비율 증가는 일반계품종보다 통일계정종에서 현저하였다.

  • PDF

Effect of Al Content on the Gas-Phase Dehydration of Glycerol over Silica-Alumina-Supported Silicotungstic Acid Catalysts

  • Kim, Yong-Tae;You, Su-Jin;Jung, Kwang-Deog;Park, Eun-Duck
    • Bulletin of the Korean Chemical Society
    • /
    • 제33권7호
    • /
    • pp.2369-2377
    • /
    • 2012
  • The gas-phase dehydration of glycerol to acrolein was carried out over silicotungstic acid ($H_4SiW_{12}O_{40}{\cdot}xH_2O$, HSiW) catalysts supported on $SiO_2$, ${\eta}-Al_2O_3$, and silica-aluminas with different Al contents. The HSiW catalysts supported on silica-aluminas showed higher glycerol conversions and acrolein yields during the initial 2 h at $315^{\circ}C$ than did $SiO_2$- and ${\eta}-Al_2O_3$-supported HSiW catalysts. Among the tested catalysts, HSiW/$Si_{0.9}Al_{0.1}O_x$ exhibited the highest space-time yield during the initial 2 h. The loaded HSiW species can change the acid types and suppress the formation of carbonaceous species on Al-rich silica-aluminas. The deactivated HSiW supported on silica-aluminas can be fully regenerated after calcination in air at $500^{\circ}C$. As long as the molar ratio between water and glycerol was in the range of 2-11, the acrolein selectivity increased significantly with increasing water content in the feed, while the surface carbon content decreased owing to the suppression of heavy compounds.

SiO2와 3Y-TZP 첨가가 지르콘의 기계적 물성에 미치는 영향 (Effects of SiO2 and 3Y-TZP on Mechanical Properties of Zircon)

  • 장호수;조범래
    • 한국재료학회지
    • /
    • 제26권4호
    • /
    • pp.182-186
    • /
    • 2016
  • Zircon, having excellent thermal, chemical, and mechanical properties, is utilized in refractory materials, electronic materials, chemical machines, structural materials, etc. However, zircon generally shows thermal dissociation to zirconia($ZrO_2$) and silica($SiO_2$) around the sintering temperature of $1540^{\circ}C$, and when zircon particles are small and impurities are present, thermal dissociation is known to occur at around $1100^{\circ}C$. This reduces the mechanical properties of $ZrSiO_4$. In this research, the effect of adding $SiO_2$ and 3Y-TZP to $ZrSiO_4$ has been studied in order to suppress dissociation and improve the mechanical properties. Addition of $SiO_2$ suppressed the dissociation of $ZrSiO_4$ at lower temperatures. It also enabled optimum packing between the particles, resulting in a dense microstructure and good mechanical properties. When 3Y-TZP was added, recombination with the dissociated $SiO_2$ resulted in good mechanical properties by suppressing the generation of pores and the densification of the microstructure.

Phosphomolybdic Acid Supported on Silica Gel as an Efficient and Reusable Catalyst for Cyanosilylation of Aldehydes

  • Kadam, Santosh T.;Kim, Sung-Soo
    • Bulletin of the Korean Chemical Society
    • /
    • 제29권7호
    • /
    • pp.1320-1322
    • /
    • 2008
  • Phosphomolybdic acid supported on silica gel (PMA-$SiO_2$) is an efficient catalyst for the activation of TMSCN for the facile cyanosilylation of various aldehydes. Cyano transfer from TMSCN to aldehyde proceeds smoothly at rt in presence of 0.8 mol % of PMA-$SiO_2$ leading to a range of cyanosilylether in excellent yield (mostly over 93%) within short reaction time (30 min). The catalyst can be recovered and reused several times without loss of activity.

실리카 나노입자 표면에 CdS 나노입자의 제조 및 평가 (Preparation and characterization of CdS nanoparticle on the surface of silica nanoparticles)

  • 강은옥;최성호;;이광필
    • 분석과학
    • /
    • 제20권5호
    • /
    • pp.413-418
    • /
    • 2007
  • 방사선 방법에 의해 실리카 나노입자에 CdS 나노입자를 코팅하였다. TEM분석결과, $SiO_2$ 나노입자 표면에 CdS의 입자의 크기는 대략 20 nm임을 확인 하였다. 또한, XRD 분석결과 결정체 화합물임을 확인하였다. PL 분석결과 PVP-CdS 나노입자와 $SiO_2$@CdS 복합체의 경우, 방출특성이 상당히 다르다는 것이 확인되었다. PVP-CdS의 경우, 방출스펙트럼이 550 nm-600 nm 에서 나타나고, $SiO_2$@CdS의 방출스펙트럼의 경우 단파장 이동함을 확인하였다. 또한 새로운 피이크 (450 nm) 나타남을 확인하였는데, 이는 CdS 의 유발양자 제한 효과에 의한 것으로 사료된다.

소량의 $SiO_2$가 첨가된 Calcium Aluminate 유리의 특성 및 구조 (Characteristics and Structural Evolution of Low-Silica Calcium Aluminate Glasses)

  • 심성헌;허종;김유성
    • 한국세라믹학회지
    • /
    • 제31권7호
    • /
    • pp.695-702
    • /
    • 1994
  • Current study was undertaken to explain the structural evolution and corresponding changes in the properties of calcium aluminate glasses with the variation of SiO2 doping concentration. Calcium aluminate glasses in the compositional ranges of (100-x)(0.6CaO+0.4Al2O3)+xSiO2(where x=0~60) were fabricated. DTA analysis confirmed an anomalous behavior in glass transition temperature (Tg) with the maximum of 887$^{\circ}C$ and minimum of 859$^{\circ}C$ when x=5 and 50, respectively. densities and refractive indices monotonically decreased with increasing SiO2 content and IR transmitting cutoff shifted to shorter wavelength side when the amount of added SiO2 exceeded 5 mole%. IR fundamental vibration absorption peaks showed the change that NBOs were inclined to SiO4 tetrahedron in the low-silica region and NBO per SiO4 tetrahedra changed from 2 to 0 with increasing silica content. Based on the analysis of IR fundamental vibration absorption peaks, the model of the structural change can be proposed in three step: 1) SiO4 scavenged the NBOs located at AlO4-tetrahedra, which resulted in the increased of Tg values, 2) NBOs located in the main network again with a decrease in Tg, and 3) dominated by the decrease in the relative amount of NBOs in the glass system, where Tg re-increased.

  • PDF