• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.53-55
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using phase locked loop(PLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1838-1840
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using digital phase locked loop(DPLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.24-24
• /
• 2000

This paper proposes a design method of sliding mode observer for SISO linear systems with a disturbance input. We first construct an observer with a constant gain matrix, a feedforward injection map and an external feedforward compensation signal input. Using the second Lyapunov method, we present a sufficient condition for the existence of sliding mode observer. The proposed observer guarantees that the state error trajectories enter a certain region in finite time and remain inside thereafter.

• The Journal of the Korea Contents Association
• /
• v.17 no.7
• /
• pp.437-442
• /
• 2017

Previously, studies on compensation material to increase the signal intensity have been conducted which does not affect the reading of images. However, the compensation material has a concern on patient infection as it is attached directly on the skin. Therefore, in this study, we tested an indirect attachment of the compensation material as an alternative method of the direct attachment. The silicon compensation material was fabricated in the form of a cylindrical bar and attached to each element of the 8 channel head coil. Then the signal intensities of the water phantom pre and post application of the silicon were measured. T1 and T2-weighted images were acquired using an 8-channel head coil and a 3.0T superconducting MRI. Signal intensities were measured by using an image measuring program. Paired t-test was used to verify if there were significant differences. The signal intensity before application of the silicon was significantly increased by 3.39% and 2.62% in T1 and T2 weighted images, respectively. Although the indirect attachment method had a limitation to completely replace the existing method, it was considered to be useful in patients with infectious diseases such as diabetic complications since it had a meaningful improvement in signal intensity based on the filling factor increase.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.12
• /
• pp.1202-1209
• /
• 2004

This paper presents a design methodology of a Digital Servo Signal Processor for high speed CD-RW drive systems. The proposed Digital Servo Signal Processor enables us to develop CD-related systems for the very high speed applications and is one of the key components of the CD-RW systems. The proposed center compensation servo control is newly built for an actuator shaking due to the fast response of a step motor when it jumps to a long distance. A control method compensating for eccentricity of a disc is implemented for operating robustly at a higher rotational speed. This servo mechanism is more size efficient and less power consumed because it is implemented using a ARM7 embedded processor and hardware digital filters. Furthermore, it is convenient to upgrade firmware for the future required functions. From experimental results, we can see that the performance of the control system is improved greatly. The proposed servo algorithm shows a shorter setting time including a pull-in time and a faster access time. It can be applied easily to the DVD-ROM and the DVD-RAM which have the same optical structure.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.72-79
• /
• 2003

We proposed a noble algorithm using DOP (degree of polarization) not only as feedback signal but alto as feed-forward signal for the compensation of higher-order PMD effect. In the proposed algorithm, DOP after the first-order PMD compensation is considered as the indicator of the amount of residual higher-order PMD. This algorithm has the merit that DOF (degree of freedom) of the system can be limited to the level of the first-order PMD compensation system. Owing to the limited DOF, the reliability of the system can be enhanced and the complexity of the implementation can be degraded. For the analysis of the algorithm, we simulated the 10Gbps NRZ transmission system and obtained the result that the system outage probability can be reduced as much as three times with respect to the only first-order PMD compensation case.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.53-58
• /
• 2018

A novel X-band high speed frequency sweep signal generator based on a tunable optoelectronic oscillator (OEO) incorporating a frequency-swept laser is presented and the theoretical fundamentals of the design are explained. A prototype of the generator with tuning range from 8.8552 GHz to 10.3992 GHz and a fine step about 8 MHz is achieved. The generated radiofrequency signal with a single sideband (SSB) phase noise lower than -100 dBc/Hz@10KHz is experimentally demonstrated within the whole tunable range, without any narrow RF band-pass filters in the loop. And the tuning speed of the frequency sweep signal generator can reach to over 1 GHz/s benefiting from applying a novel dispersion compensation modular instead of several tens of kilometers of optical fiber delay line in the system.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1995.06a
• /
• pp.165-170
• /
• 1995

In this paper, it is attempted to apply the adaptive digital signal processing to compensate for a linear distortion of a loudspeaker and implement a real time hardware for that purpose. The real time system is implemented by using the DSP56001, a general purpose signal processor, as a host processor and the DSP56200, a cascadable adaptive FIR filter peripheral chip, as an adaptive digital filter. The system has 1000 taps at a 44.1kHz. After inverse modeling of under_compensation_speaker, the system reduces loudspeaker's linear distortions by pre-processing an input audio signal to loudspeaker. The experiment shows satisfactory results; after adaption with white noise as input signal for 60sec, the flat amplitude and linear phase frequency characteristics is found to lie over a wide frequency range of 100Hz to 20kHz.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.5
• /
• pp.582-589
• /
• 2016

Multi-mode monopulse system is widely used for satellite terminal like UAV because of high tracking accuracy and low size/weight profile. In order to calculate tracking error, Multi-mode monopulse system utilizes high-order mode signal, and it should have enough C/N(carrier to noise) level therefore tracking system needs narrow band filtering of received satellite beacon signal as much as possible. However, UAV suffers for beacon frequency drift derived from Doppler effect due to satellite figure 8 movement and UAV maneuvering. Therefore wideband signal processing needs to be considered in advance for exact doppler compensation and consequent time delay. In this paper, we propose the multi-stage Digital Signal processing system for beacon signal, which could minimize the signal delay under high Doppler and low C/N condition.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.638-646
• /
• 2005

In recent wireless communications, direct conversion transceiver or If sampling SDR-based receivers have being designed as an alternative to conventional transceiver topologies. In direct conversion receiver a.chitectu.e, the 1.equency/phase offset between the RF input signal and the local oscillator signal is a major impairment factor even though the conventional AFC/APC compensates the service deterioration due to the offset. To rover the limited tracking range of the conventional method and effectively aid compensation scheme in terms of I/Q channel imbalances, the frequency/phase offset compensation in RF-front end signal stage is proposed in this paper. In RF-front end, the varying phase offset besides the fixed large frequency/phase offset are corrected by using early-late phase compensator. A more simple frequency and phase tacking function in digital signal processing stage of direct conversion receiver is effectively available by an ingenious frequency/phase offset tracking method in RF front-end stage.