• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.3
• /
• pp.95-100
• /
• 2004

A control alogorithm using sliding mode and neural network for Buck type DC-DC converter is presented. Also, we conform a rightness the proposal method by comparing a theoretical values and experimental values obtained from experiment using DSP(digital signal processor). Performance comparisons made with the general hysteresis controller clearly bring out the superior performance of the proposal neural network controller. This paper will be applied to other power conversion system using the proposal neural network controller.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1277-1281
• /
• 2005

FPGA has been widely used in communication system. In this paper, we made 10 layers PCB on protection of signal noise and data lose with FPGA. We analyzed about change of the data transmission speed and length according to input frequency. The length of transmission line from FPGA's output-pin to output-port on PCB board is 13cm and extended lengths for test are 30cm, 60cm and 10cm. We knew that data can be stably transmitted to 100Mbps at transmission line length of 30cm.

• Journal of information and communication convergence engineering
• /
• v.8 no.6
• /
• pp.655-659
• /
• 2010

In the conventional PNC scheme, the relay node requires simultaneous transmission of two source nodes with strict power control and carrier-phase matching between two received symbols. However, this pre-equalization process at source nodes is not practical in fading channels. In this letter, we propose a novel physical-layer network coding (PNC) scheme with log-likelihood ratio (LLR) conversion for fading channels, which utilizes not pre-equalizer at transmitters (source nodes) but joint detector at receiver (relay node). The proposed PNC requires only channel side information at the receiver (CSIR), which is far more practical assumption in fading channels. In addition, the proposed PNC scheme can use the conventional modulation scheme like M-QAM regardless of modulation order, while the conventional PNC scheme requires reconfiguration of modulation scheme at the source nodes for detection of the received signal at relay node. We consider the combination of the proposed PNC and channel coding, and find that the proposed PNC scheme is easily combined the linear channel codes such as turbo codes, LDPC, and convolutional codes.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.4
• /
• pp.423-434
• /
• 1989

In this paper, a PRS transmission system using TMRCP as the unit pulse is proposed, which solves the problems occur when the PRS method will be applied to the digital transmultiplexer for each channel. And a design technique which uses this PRS method for the FFT polyphase filter transmultiplexer concept is given. TMRCP-PRS signal require a bandwidth about 2.5KHz(including some guard-band) for a 4-KHz bandlimited voice channel. Therefore, in he 24 channel transmission line, it gives the same advantages as he ordinary PRS system and sloves the inter-channel interference problems. And its good speed-tolerance reduces the time-errors by the environments and the power loss, so it makes the system to be stable. The total system, however, attaces the filters for PCM-PRS, PRS-PCM conversion before and after the transmultiplexer respectively.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.382-391
• /
• 2005

Increasing of the nonlinear type power electronics equipment, power conditioning systems (PCS) have been researched and developed for many years in order to compensate for harmonic disturbances and reactive power. PCS's not only improve harmonic current and power factor in the ac grid line but also achieves energy saving used by the renewable energy source (RES). In this paper, the implementation of a current controlled voltage source inverter (CCVSI) using RES for PCS is presented. The basic principle and control algorithm is theoretically analyzed and the design methodology of the system is discussed. The proposed system could achieve power quality control (PQC) to reduce harmonic current and improve power factor, and demand side management (DSM) to supply active power simultaneously, which are both operated by the polarized ramp time (PRT) current control algorithm and the grid-interactive current control algorithm. A 1KVA test model of the CCVSI has been built using IGBT controlled by a digital signal processor (DSP). To verify the proposed system, a comprehensive evaluation with theoretical analysis, simulation and experimental results is presented.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.2
• /
• pp.191-198
• /
• 1995

In order to evaluate the distribution and behaviour of atmospheric particulate metals in high-altitude area, we collected 22 aerosol samples using a high volume air sampler at Soback Mt. Meteorological Observation Station from Jan. to Nov. 1993 and analysed for metals (Al, Fe, Mg, Na, Ca, Mn, Co, Ni, Cu, Zn, Cd, and Pb) with ICP/AES and ICP/MS. Although sampling site is located in high-altitude and far from local sources of atmospheric pollutants, enrichments of metals are 2 times higher than those of western coastal reural area. This fact may imply that of metallic pollutants in the coastal rural site were came from further western side (e.g. China), atmospheric metals in this study area contain the signal of metropolitan cities located in the main wind direction (NNW). Sea salts are negligible in the aerosol particle population because reference elements of sea salts (Na, Mg) are all originated from soil particles. The contents of soil particles in aerosols are highest in spring and lowest in winter. Atmospheric enriched elements (Ni, Cu, Zn, Cd and Pb) are diluted with soil particles, especially during the yellow sand period. The results of factor analysis suggest possibility of interpreting their chemical significance in terms of sources (soil, pollutants) and gas-particle conversion processes (formation of ammonium sulfates, ammonium nitrates and/or their mixtures).

• Journal of Sensor Science and Technology
• /
• v.18 no.2
• /
• pp.128-134
• /
• 2009

Integrated circuit of a new neuron chain with a synapse function for Hodgkin-Huxley model which is a good electrical model about a real biological neuron is implemented in a $0.5{\mu}m$ 1 poly 2 metal CMOS technology. Pulse type neuron chain consist of series connected current controlled single neurons through synapses. For the realization of the single neuron, a pair of voltage mode oscillators using operational transconductance amplifiers and capacitors is used. The synapse block which is a connection element between neurons consist of a voltage-current conversion circuit using current mirror. SPICE simulation results of the proposed circuit show 160 mV amplitude pulse output and propagation of the signal through synapses. Measurements of the fabricated pulse type neuron chip in condition of ${\pm}2.5\;V$ power supply are shown and compared with the simulated results.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.169-174
• /
• 2015

In this study, we developed a system to detect the various defects in the metallic objects using the phenomenon that the defects cause the changes of the natural resonant frequencies. Our system consists of a FFT Amp, an Auto Impact Hammer, a Hammer controller and a PC. Auto Impact Hammer creates vibrations in the metallic objects when tapped on the surface. These vibrational signals are converted to the voltage signals by an acceleration sensor attached to the metallic part surface. These analog voltage signals were fed into an ADC (analog-digital converter) and an FFT (fast fourier transform) conversion in the FFT Amp to obtain the digital data in the frequency domain. Labview graphical program was used to process the digital data from th FFT amp to display the spectrum. We compared those spectra with the standard spectrum to find the shifts in the resonant frequencies of the metal parts, and thus detecting the defects. We used PCB's acceleration sensor and TI's TMS320F28335 DSP (digital signal processor) to obtain the resolution of 2.93 Hz and to analyze the frequencies up to 44 kHz.

• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.31-35
• /
• 2018

This paper describes a low-power, SNDR (signal-to-noise and distortion ration) enhanced SAR (successive approximation register) type 12b ADC (analog-to-digital converter) with noise shaping technique. For low power consumption and small chip size of the DAC (digital-to-analog converter), the top plate sampling technique and the dummy capacitor switching technique are used to implement 12b operation with a 10b capacitor array in DAC. Noise shaping technique is applied to improve the SNDR by reducing the errors from the mismatching of DAC capacitor arrays, the errors caused by attenuation capacitor and the errors from the comparator noise. The proposed SAR ADC is designed with a $0.18{\mu}m$ CMOS process. The simulation results show that the SNDR of the SAR ADC without the noise shaping technique is 71 dB and that of the SAR ADC with the noise shaping technique is 84 dB. We can achieve the 13 dB improvement in SNDR with this noise shaping technique. The power consumption is $73.8{\mu}W$ and the FoM (figure-of-merit) is 5.2fJ/conversion-step.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.4
• /
• pp.409-413
• /
• 2006

This paper deals with the design and testing of a simulator system for microgrids with distributed generations. This system is composed of a Real Time Digital Simulator (RTDS) and a power amplifier. The RTDS parts are operated for real time simulation for the microgrid model and the distributed generation source model. The power amplifiers are operated fur amplification of the RTDS's simulated output signal, which is a node voltage of the microgrid and distributed generation source. In this paper, we represent an RTDS system design, specification and test results of a power amplifier and simulation results of a PV (Photovoltaic) system and wind turbine system. The proposed system is applicable for development and performance testing of a PCS (Power Conversion System) for renewable energy sources.