• 대한조선학회 특별논문집
• /
• 대한조선학회 2013년도 특별논문집
• /
• pp.81-84
• /
• 2013

일반적인 Bulk carrier는 Single deck, Double bottom, Hopper side tank, Top side tank와 함께 Single side skin 또는 Double side skin으로 구성되어 Single hull bulk carrier 또는 Double hull bulk carrier라 불린다. 본 논문의 연구선박인 Double hull bulk carrier는 CSR에서 규정짓고 있는 Double hull bulk carrier의 특징 중 Hopper side tank가 없기에 일반적인 Double hull bulk carrier와는 다른 구조를 가진다. 구조적 특징으로는 Inner bottom과 Inner hull 연결부위에 응력 집중 발생, Side shell의 Shear에 대해 구조적 안전성, Double hull에 대한 CSR for bulk carrier의 Rule적용 여부에 대한 판단 등이 있다. 따라서 본 연구에서는 Double hull bulk carrier의 구조적 특징과 구조해석을 통한 응력 집중 부위의 평가 및 Fatigue analysis을 통한 피로수명을 계산하여 이를 통해 구조의 안전성을 살펴보고자 한다.

• 대한조선학회논문집
• /
• 제38권3호
• /
• pp.14-22
• /
• 2001

본 논문에서는 2,500톤급 삼동형 호위구축함의 선형설계와 저항추진특성에 대한 연구 결과를 보인다. 보조선체의 형상과 그 설치 위치가 삼동선의 저항성능에 미치는 영향을 파악하기 위하여 일련의 저항시험과 수치계산을 수행하였다. 그리고 삼동선의 추진효율을 조사하기 위하여 추진시험을 수행하였으며, 실선 크기에서 삼동선과 유사 단동선들의 저항추진성능을 비교하였다. 본 연구를 통하여 보조선체의 길이 방향 위치가 삼동선의 저항특성에 큰 영향을 미치며, 보조선체의 형상과 폭 방향의 위치는 그 영향이 작은 것을 알 수 있었다. 보조선체의 중심이 길이 방향으로 주선체의 선수나 선미 가까운 곳에 설치될 때 삼동선의 저항성능이 우수한 결과를 보였는데, 이는 주선체로부터 생성된 가장 큰 선수파의 파저에 보조선체의 선수가 놓이는 곳이다. 그리고, 삼동선의 저항추진성능은 유사 단동선에 비하여 중속 이상의 구간에서 우수한 결과를 보였다.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2009년도 특별논문집
• /
• pp.65-70
• /
• 2009

In case that tug boat pushes side structures of other large vessels to maneuver, it is required that contacted side structures of the maneuvered vessels have enough structural safety against tug push loads. The objective of this study is to evaluate the structural effect of carling which is installed between side longitudinal stiffeners. A comparative study of side structures with carling and without carling is performed to evaluate the effect of carling member by both FE analysis. According to the result, it is found that the carlings play effective role in the strength of side plates and side longitudinal stiffeners against tug push loads.

• Journal of Ship and Ocean Technology
• /
• 제6권2호
• /
• pp.23-36
• /
• 2002

This paper describes the powering, seakeeping and maneuvering performances for a 2,500-ton class trimaran. Influence of the side-hull forms and location of those in longitudinal and transverse direction to resistance performance was systematically investigated by a series of model tests and numerical calculations. It was found that the longitudinal location of side-hulls was the most influential design parameter to the resistance performance of the trimaran and the optimum location of side-hull depends on ship speeds. When the side-hull stem is located near the primary wave hollow generated by the main hull, the trimaran shows the best resistance performance. Powering performance of the trimaran is superior to those of similar mono-hull ships. Seakeeping model tests for the trimaran were executed and the results were compared with the theoretical results of a similar mono-hull ship. Generally speaking, seakeeping performance of the trimaran is superior to that of a mono-hull ship. In particular, pitching and rolling performance of the trimaran is excellent, which is due to the increased length and breadth. Maneuvering model tests using a HPMM equipment were executed to evaluate the maneuvering performance of the trimaran. Maneuvering simulation was performed using the maneuvering coefficients from the model tests. The results show that the control ability of heading angle and the direction keeping stability of the trimaran is excellent, even though the turning performance is rather worse compared to those of a similar mono-hull ship.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.

• 대한조선학회논문집
• /
• 제41권3호
• /
• pp.60-71
• /
• 2004

Nowadays, We have had a growing interest in high-speed vessels' because it is very important to save time and cost in marine transportation. The development of hull form for high-speed vessels is high priority to secure the competitive power for the transportation of cargos. Therefore, the demand of the high-speed vessels is gradually increased, but the conventional hull forms are limited by rapidly increasing resistance upon the increase of ship speed in high-speed region. Therefore, new concepts for the hull form of high-speed vessels have been requested. One of the derived hull forms for that demand is the hull form of trimaran type. Trimaran has a very slender main hull as compared with conventional single hull so that is reduced in wave resistance. The slender main hull has the undesirable characteristics of stability, but two side hulls make up for the week points in the stability. That is, trimaran is able to have desirable performances for the resistance and stability. In this paper, for the design of 200TEU class container vessel with trimaran type, which will be cruised in Yellow-Sea region, firstly a preliminary hull is designed, and the model test is carried out with the variation of side hull position. From the experience of the preliminary hull form design, an improved hull form for the 200TEU container are designed, and the model tests are carried out. Also, a numerical computation technique is adopted for the simulation of flow phenomena around the designed hull forms. The final hull form is compared with existing ships for the resistance performance from the computation with computer and ship model tests.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2005년도 특별논문집
• /
• pp.107-112
• /
• 2005

During assembling the ship block, the lifting and turnover events are not only inevitable but also very important for safety aspects and block accuracy. However, they have been executed in empirical ways rather than numerical ways in consideration of the building schedule. In this paper, a structural analysis has been carried out for the container ship side block that collapsed in the course turnover stage. As a result, the causes of collapse and countermeasure plans are presented.

• 대한조선학회논문집
• /
• 제48권4호
• /
• pp.317-324
• /
• 2011

When a ship proceeds in confined water, like canal, the water ahead of ship is pushed by hull. This pushed water returns to the side and under the hull, and this returned water will make fluid velocity higher at the side and under the hull, compared to the case in the infinite water depth. Due to the higher velocity, the pressure under the hull will decrease, resulting in the ship drop. This phenomenon is called "ship squat" and ship squat will result in various marine accidents. In this paper, for predicting ship squat, numerical calculation was carried out using commercial CFD code, FLUENT. To confirm wave pattern profile around the ship, VOF(Volume of Fluid) method was applied. The calculated results were compared with other paper's results and empirical methods.

• 한국해양공학회지
• /
• 제18권1호
• /
• pp.80-84
• /
• 2004

The initial hull form of a 3 G/T and 30 knots class coastal leisure boat is newly developed. The performances measured, resistance, trim and sinkage, are investigated in a high-speed, circulating water channel (CWC). The effect of a fin attached on the hull side is studied together. Wave patterns are observed to clarify the relationship between the resistance performance and the wave characteristics. It can be found that the fin plays a role of increasing the resistance performance above a certain velocity.

• 한국전자통신학회논문지
• /
• 제6권1호
• /
• pp.123-128
• /
• 2011

소형스케일용 해양부이를 위한 hull설계부분을 소개한다. hull구조설계와 부이의 모든 부분을 연결하는 설계부분에 대하여 연구하였으며, 주로 부이의 hull설계내용을 순차적으로 소개한다. 전체적인 강도와 충돌저항력을 향상시키는 방법으로 부이를 지지하는 2층 및 반지름방향의 주요구조와 함께 내벽을 이용하여 설계를 수행하였다.