• Geomechanics and Engineering
• /
• 제6권2호
• /
• pp.153-172
• /
• 2014

In order to investigate the effect of different perforation angles (the angle between the perforation direction and the maximum horizontal principal stress) on the fracture initiation and propagation during hydraulic fracturing of highly deviated well in oil & gas saturated formation, laboratory experiments of the hydraulic fracturing had been carried out on the basis of non-dimensional similar criteria by using 400^3 $mm^3$ cement cubes. A plane fracture can be produced when the perforations are placed in the direction of the maximum horizontal principal stress. When the perforation angle is $45^{\circ}$, the fractures firstly initiate from the perforations at the upper side of the wellbore, and then turn to the maximum horizontal principal stress direction. When the well deviation angle and perforation angle are both between $45^{\circ}$ and $90^{\circ}$, the fractures hardly initiate from the perforations at the lower side of the wellbore. Well azimuth (the angle between the wellbore axis and the maximum horizontal principal stress) has a little influence on the fracture geometries; however it mainly increases the fracture roughness, fracture continuity and the number of secondary fractures, and also increases the fracture initiation and propagation pressure. Oriented perforating technology should be applied in highly deviated well to obtain a single plane fracture. If the well deviation angle is smaller, the fractures may link up.

• 한국재료학회지
• /
• 제12권11호
• /
• pp.865-869
• /
• 2002

We investigated the reaction stability of titanium, cobalt and their bilayer films with side-wall spacer materials of SiO$_2$ for the salicide process. We prepared Ti 350 $\AA$, Co 150 $\AA$, Co 150 $\AA$/Ti 100 $\AA$ and Ti 100 $\AA$/Co 150 $\AA$ films on 1000 $\AA$-thick thermally grown SiO$_2$ substrates, respectively. Then the samples were rapid thermal annealed at the temperatures of $500^{\circ}C$, $600^{\circ}C$, and $700^{\circ}C$ for 20 seconds. We characterized the sheet resistance of the metallic layers with a four-point probe, surface roughness with scanning probe microscope, residual phases with an Auger depth profilometer, phase identification with a X-ray diffractometer, and cross-sectional microstructure evolution with a transmission electron microscope, respectively. We report that Ti reacted with silicon dioxide spacers above $700^{\circ}C$, Co agglomerated at $600^{\circ}C$, and Co/Ti, Ti/Co formed CoTi compound requiring a special wet process.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.308-312
• /
• 2013

In this paper, we describe experiment results using a vibration assisted hybrid femtosecond laser (${\lambda}$:795 nm) ultra-precision machining system. The hybrid system we have developed is possible that optical focal point of the femtosecond laser constantly and frequently within the range of PZT(piezoactuator) vibrator working distance. Using the hybrid system, We have experimented on brass and studied about differences of result of hole aspect ratio compare to general experiment setup of femtosecond laser system. Aspect ratio of a micro hole on brass is increased as 54% with 100 Hz vibration frequency and surface roughness of the side wall also improved compare to non-vibration.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.145-150
• /
• 2005

This paper presents an Electrotactile Display System (ETCS). One of the most important human sensory systems for human computer interaction is the sense of touch, which can be displayed to human through tactile output devices. To realize the sense of touch, electrotactile display produces controlled, localized touch sensation on the skin by passing small electric current. In electrotactile stimulation, the mechanoreceptors in the skin may be stimulated individually in order to display the sense of vibration, touch, itch, tingle, pressure etc. on the finger, palm, arm or any suitable location of the body by using appropriate electrodes and waveforms. We developed an ETCS and investigated effectiveness of the proposed system in terms of the perception of roughness of a surface by stimulating the palmar side of hand with different waveforms and the perception of direction and location information through forearm. Positive and negative pulse trains were tested with different current intensities and electrode switching times on the forearm or finger of the user with an electrode-embedded armband in order to investigate how subjects recognize displayed patterns and directions of stimulation.

• 구강회복응용과학지
• /
• 제26권3호
• /
• pp.339-347
• /
• 2010

이전에 존재하던 컴포지트와 새로운 컴포지트 사이의 결합강도의 강화는 미세 기계적 유지를 증진하기 위한 표면 거칠기의 증가가 필요하다. 이 연구는 시효처리 후의 레진 컴포지트의 repair 결합강도에 다른 표면처리의 효과를 평가하는 것이다. 알루미늄 옥사이드를 이용한 air abrasion, chair-side silica coating한 그룹들에서 대조군과 불산 적용에 비하여 유의하게 높은 결합강도를 보였다. 레진 수복물의 repair시에 air abrasion의 사용은 필요한 것으로 보이며 부가적으로 silane의 적용은 결합강도에 긍정적 영향을 미치는 것으로 보인다.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.55-64
• /
• 2001

In this study, hemisphere and cylindrical shapes were machined for different tool paths and machining conditions with ball endmill cutters. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting is obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. Roundness values were found in least roundness error when down-milling in upward cutting. It is obtained the very little difference between 90。and 45。 of inclination position angle. The best surface roughness value was obtained in upward up-milling and showed different tendency with tool deflection and cutting force. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. Therefore, this phenomenon which is received over cutting resistance can be caused of chatter.

• 한국수소및신에너지학회논문집
• /
• 제18권2호
• /
• pp.182-188
• /
• 2007

[ $Zr_{50}-Ni_{27}-Nb_{18}-Co_5$ ] amorphous alloys ribbon was prepared by a single-roller melt-spinning technique. In order to improve the hydrogen kinetics Pd-coating were carried out on each side of the amorphous ribbon. Pd prevents oxidation of Zr and catalyses the dissociation of molecular hydrogen to atomic hydrogen. In this work, the hydrogen embrittlement and surface properties on Zr-based amorphous alloys were investigated. The Zr-based amorphous alloys were characterized by X-ray diffractometry(XRD) and differential scanning calorimetry(DSC). The morphology of surface and roughness was observed by using scanning electron microscopy(SEM) and atomic force microscopy (AFM). A lattice parameter of both Pd and Zr-based amorphous alloy was increased after hydrogen permeation at 473 K. After hydrogen permeation at 473 K, some cracks were observed on the surface of Pd, which was the cause for the hydrogen embrittlement. The crystallization temperature of Zr-based amorphous alloy was decreased due to the permeated hydrogen.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.537-540
• /
• 1999

Effect of alignment layers on pretilt angle generation and electrical characteristics in nematic liquid crystal(NLC) by using photo-alignment techniques on polyimide (PI) surface with side chain were studied. The generated pretilt angle of the NLC on rubbed PI surface with 1-layer is almost the same as that of the 2-layers. However, the generated pretilt angle of the NLC on photo-induced PI surface with 2-layers is larger than that of the 1-layer. Therefore, the pretilt angle of the NLC on photo-induced PI surface is attributed to surface roughness due to photo-depolymerization of the polymer with UV light irradiation on PI surface. Next we observed the same characteristics of voltage-transmittance (V-T) and response time for 1- and 2-layers on PI surface. We also observed the same voltage holding ratio (VHR) characteristics for 1- and 2-layers on photo-aligned PI surface. Consequently, we suggest that the VHR of photo-aligned TN-LCD is higher than that of the rubbing-aligned TN-LCD.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권9호
• /
• pp.417-422
• /
• 2002

ZnO thin films were deposited on various substrates, such as Si-(111), SiO$_2$(5000 $\AA$ by thermal CVD)/Si-(100), and SiO$_2$(2000 $\AA$ by RF sputtering)/Si-(100). The (002)-orientation, surface morphology and roughness, and electrical resistivity of deposited films were measured and compared in terms of substrate. Surface acoustic wave(SAW) filters with a multilayered configuration of IDT/ZnO/SiO$_2$/Si were also fabricated and the IDT was obtained using a lift-off method. From the frequency-response characteristics of fabricated devices, the insertion loss and side-lobe rejection were estimated. The experimental results showed that the (002)-oriented growth nature of ZnO films, which played a crucial role of determining the characteristic of SAW device, was strong1y dependent upon the SiO$_2$buffer.

• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.151-156
• /
• 2000

Effects of alignment layers on pretilt nagle generation and electrical characteristics in nematic liquid crystal(NLC) by using photo-alignment techniques on polyimide PI) surface with side chain were studied. The generated pretilt angle of the NLC on rubbed PI surface with 1-layer is almost the same as that with the 2-layers. However, the generated pretilt angle of the NLC on photo-induced PI surface with 2-layers is larger than that with the 1-layer. The different mechanism of pretilt generation in NLC was observed on the rubbing and photo-alignment method. Therefore, the pretilt angle of the NLC on photo-induced PI surface is attributed to surface roughness due to photo-dissociation on the polymer with UV light irradiation on PI surface. We observed the same characteristics of voltage-transmittance (V-T) and response time for 1- and 2-layers on PI surface. Consequently, we sugest that the VHR of photo-aligned TN-LCD is higher than that of the rubbing-aligned TN-LCD.