• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.58-65
• /
• 2011

The specific objective of this study was to develop an IRDS (integrated receiver drier subcooling) condenser model for use in a mobile air-conditioning system. A three-zone model based on the desuperheating, two-phase, and subcooling sections of a condenser could be used to estimate the performance with a good accuracy. Overall heat transfer coefficients for each of the three sections, expressed as a function of the air velocity across the condenser and refrigerant mass flow rate and the model using the elemental difference method incorporate calculations to determine the pressure drop, heat performance within the condenser and it includes physical parameters (pass, tube hole size and length) that can be varied to analyze potential design changes without exhaustive experimental efforts. it was found that an accuracy of heat performance was within 5% in case of using the various condensers, the refrigerant pressure drop was predicted within 25% and the pressure drop of air side was well matched with experiment data within 4%.

• Journal of architectural history
• /
• v.26 no.5
• /
• pp.19-26
• /
• 2017

This paper aimed to identify the architectural characteristics of the chimi excavated from ancient ruins, especially middle gate remains of Bunhwangsa Temple in the Unified Silla period. Middle gate had planned $3{\times}2$ with 295mm measuring unit and gabled building. Detailed study of the shape of chimi of the middle gate restored by related field experts reveals as follows. 1) Height of chimi is 4.5(130.6cm) of Tang's system of measurement classified as large one. 2) The front and back side square hole is made for transverse timber placement. 3) Position of chimi is not the end of the ridge of roof, it moved toward the center. 4) Construction method of chimi is structured with smaller beam and center column. 5) Width and height of the ridge is less than 38cm and 54cm to be approximately, Width and height of the gabled ridge is less than 38cm and 50cm. 6) This chimi is considered to be very unique when compared to existing ancient restored chimis, it is designed to be advantageous to the chimi construction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.1-10
• /
• 1998

In this paper, we investigated the improvement of characteristics of knock, emission and fuel consumption rate by optimizing the location and size of water transfer holes in cylinder head gasket without change of engine water jacket design itself. The cooling system was modified in the direction of reducing the metal temperature in the head and increasing the metal temperature in the block. The optimization of water transfer holes in cylinder head gasket was obtained by "flow visualization test". The water transfer holes were concentrated in front side of the engine in order to reduce thermal boundary layer in the water jacket of No. 2 and No. 3 combustion changer in the cylinder head, which would have a large knock intensity, and increase thermal boundary layer in the water jacket of the cylinder block. When the modified coolant flow pattern was applied as proposed in this paper, the knock characteristic was improved. The spark timing was advanced up to 2$^{\circ}$ in low and middle speed range at a full load. In addition, HC emission at MBT was reduced by 5.2%, and the fuel consumption rate was decreased up to 1% in the driving condition of 2400 rpm and 250 KPa. However, since this coolant flow pattern mentioned in this paper might deteriorate the performance of vehicle cooling system due to the coolant flow rate reduction, a properly optimized point should be obtained. obtained.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.60-68
• /
• 2010

In this study, the seepage flow monitoring method by hydaulic head loss rate graph was developed for the purpose of monitoring the seepage flow from the see side or from the lake on sea dike in which seepage force was varied periodically. The hydraulic head loss rate was defined in this method. The value of the rate is in the range from 0 to 1. the value of 0 means perfectly free flow of seepage. the value of 1 means perfect waterproofing. The value of coefficient of determination in the hydraulic head loss rate graph closer to 1 means that the seepage flow way is stable. The value of coefficient of determination in the hydraulic head loss rate graph closer to 0 means that the hole may exist or the piping may be in the progress. The pore water pressure data measured in Saemangeum sea dike was analyzed with the developed method The result showed that the variation of seepage flow state was detected sensitively by this method and the interception effect of sea dike could be estimated quantitatively.

• Journal of Korean Neurosurgical Society
• /
• v.58 no.3
• /
• pp.301-303
• /
• 2015

We report on a case of an 87-year-old woman who showed spontaneous resolution of a large chronic subdural hematoma which required surgical decompression. She had suffered from confused mentality and right side weakness of motor grade II for 10 days. The initial brain CT scan showed a 22 mm thick low density lesion located in the left fronto-temporo-parietal region with midline shift (12 mm) which required emergency decompression. However, because she and her family did not want surgery, she was followed up in the outpatient clinic. Five months later, follow up brain CT showed that the CSDH had disappeared and the patient became neurologically normal. The reasons for spontaneous resolution of CSDH remain unclear. We discuss the possible relation between mechanisms of physio-pathogenesis and spontaneous resolution of a large chronic subdural hematoma (CSH) in an elderly patient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.9
• /
• pp.772-779
• /
• 2007

In this paper, thermo-flow characteristics of an outer-rotor type BLDC motor are numerically analyzed using three-dimensional turbulence modeling. On the rotor of the BLDC motor, cooling blades and cooling holes are existed for the enhanced cooling performances. Rotating the blades and holes generates axial air flow streaming into inner rotor side and passing through stator slots, which cools down stator by forced convection. Operating tests are performed and the numerical temperature fields are found to be in good agreement with experimental results. A new design of the BLDC motor has also been developed and major design parameters such as the arrangement of cooling holes, the area of cooling holes and cooling blades, and the cooling blade angle, are analyzed for the enhanced convective heat transfer rate. It is found that the convective heat transfer rate of the new BLDC motor model is increased by about 8.1%, compared to that of the reference model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.471-477
• /
• 2015

In this study, the property of crack propagation and growth at high tension steel plate existed with center crack is investigated. The behaviors of fracture mechanics due to existence or not of hole near the center crack in specimen and the length of crack length are investigated when the load is applied at the one side end of specimen. Stress, deformation and deformation of this specimen are evaluated through simulation analysis. By the analysis results at this study, stress intensity factors are obtained. The damage happened at machine or structure with crack or defect can be estimated on the basis of study results.

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.140-146
• /
• 2002

The tulip-inversion of flames in half-open tubes was investigated experimentally. Experiments was carried out in tubes with various shapes. The image of a flame propagation were pictured by HICCD(High speed intensified CCD) and the dynamic pressure of tubes was measured by a piezo pressure sensor. By analyzing the images of the flame propagation, we found the time and the distance for the occurrence of tulip-inversion. Regardless of the shapes of tubes, time of tulip-inversion are similar and inversely proportional to the burning velocity. But distances have different tendency. In a straight tube, the distance of tulip-inversion increases when the burning velocity increases. But in a converging tube, the distance of tulip-inversion decreases when a burning velocity increases. And the distance of tulip-inversion in a converging tube is much smaller than the distance of tulip-inversion in a straight tube. These results are caused by the deceleration of a flame when the diameter of a hole in open-side of a tube is small. The deceleration causes little effect on the time of tulip-inversion.

• Journal of Korean Physical Therapy Science
• /
• v.22 no.1
• /
• pp.11-17
• /
• 2015

Purpose : The current study examines changes of static uprighting balance in the visual input characteristics. Method : Total 50 person(male 16, female 34) were participated in this study. They were tested with 'hole in the card' for identification of dominant eye's side, then they were divided 3 groups(both visual input group, dominant visual input group, and non-dominant visual input group). 3 groups were measured with Romberg test on the force platform device to compare the static uprighting balance characteristics ; moving distance, mean velocity, and sway area of the CoM(center of mass), during 20 seconds. Results : The results by one-way repeated measure ANOVA were as follows. In moving distance and mean velocity of CoM, non-dominant visual input group was unstable than dominant visual group and both visual input group(p<0.05). But, in sway area of CoM, significant difference was not existed statistically. Conclusion : These result can be applied to design the static uprighting balance program using visual input mediation.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.41
• /
• pp.7.1-7.5
• /
• 2019

Background: To introduce a novel technique for advancement genioplasty helping surgeons to avoid soft tissue difficulties especially in short-faced patients with deep mentolabial fold and everted lower lip. Case presentation: In a trapezius-shaped, osteotomy was performed in the chin region. The mobilized segment was advanced, and the existing gap was grafted using interpositional allograft materials. Each side had been fixated by three-hole plates and two screws. The outcomes revealed no change in lower anterior teeth vitality. The patients did not report any changes of sensation in lower lip and chin either. The measurements indicated no increase in depth of mentolabial fold in patients undergoing this surgical technique. The postoperative evaluation showed a successful esthetic outcome for the patient and the surgeon concurrently. Conclusion: Based on our experience, the authors concluded that the Balcony technique is a simple and reliable procedure for patients with a deep mentolabial fold.