• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.688-692
• /
• 2004

In this paper, zinc oxide (ZnO) films with c-axis (002) orientation have been successfully deposited on the Al/Si substrate by rf magnetron sputtering method. The deposited films were characterized by substate temperature. Physical and structural properties of the deposited films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurement. Electrical Properties of the deposited films were investigated by 4-poing probe and LCR meter measurement. The optimal condition in this experimental result was found at foot of the substrate temperature and shown good film quality for FBAR application.

• 한국재료학회지
• /
• 제9권6호
• /
• pp.609-614
• /
• 1999

The effect of the amount of $SiO_2$dopant on the behavior of $AlO_2$$O_3$-composite formation by melt oxdation of Al-alloy was examined in this paper. The $SiO_2$powder was spread on the top surface of the Al-1Mg-3-Si-5Zn-1Cu alloy in th alumina crucible. The selected amount of each powder was 0.03, 0.10, 0.16g/$\textrm{cm}^2$. The oxidation behavior was determined by observing the weight gain after the heat treatment for 10 hours at 1373K. The macroscopic structure of formed oxide layer was examined by an optical microscope. The top surface and the cross-section of the grown oxide layer were investigated by SEM and analysed by EDX. The $SiO_2$ powder was determined to enhance oxidation by thermit reaction with Al which reduced the growth incubation period of the oxidation layer. As the amount of the $SiO_2$dopant increased, the growth rate decreased due to the precipitated Si which blocked the Al-alloy channel in the composite materials. However, more uniform layer was obtained due to the occurrance of the enhanced oxidation reaction in the whole alloy surface compared to the case of addition of less amount of dopant.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.410-410
• /
• 2013

Next-generation nonvolatile memory (NVM) has attracted increasing attention about emerging NVMs such as ferroelectric random access memory, phase-change random access memory, magnetic random access memory and resistance random access memory (RRAM). Previous studies have demonstrated that RRAM is promising because of its excellent properties, including simple structure, high speed and high density integration. Many research groups have reported a lot of metal oxides as resistive materials like TiO2, NiO, SrTiO3 and ZnO [1]. Among them, the ZnO-based film is one of the most promising materials for RRAM because of its good switching characteristics, reliability and high transparency [2]. However, in many studies about ZnO-based RRAMs, there was a problem to get lower current level for reducing the operating power dissipation and improving the device reliability such an endurance and an retention time of memory devices. Thus in this paper, we investigated that highly reproducible bipolar resistive switching characteristics of W doped ZnO RRAM device and it showed low resistive switching current level and large ON/OFF ratio. This may be caused by the interdiffusion of the W atoms in the ZnO film, whch serves as dopants, and leakage current would rise resulting in the lowering of current level [3]. In this work, a ZnO film and W doped ZnO film were fabricated on a Si substrate using RF magnetron sputtering from ZnO and W targets at room temperature with Ar gas ambient, and compared their current levels. Compared with the conventional ZnO-based RRAM, the W doped ZnO ReRAM device shows the reduction of reset current from ~$10^{-6}$ A to ~$10^{-9}$ A and large ON/OFF ratio of ~$10^3$ along with self-rectifying characteristic as shown in Fig. 1. In addition, we observed good endurance of $10^3$ times and retention time of $10^4$ s in the W doped ZnO ReRAM device. With this advantageous characteristics, W doped ZnO thin film device is a promising candidates for CMOS compatible and high-density RRAM devices.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.50-50
• /
• 2008

ZnO has been extensively studied for optoelectronic applications such as blue and ultraviolet (UV) light emitters and detectors, because it has a wide band gap (3.37 eV) anda large exciton binding energy of ~60 meV over GaN (~26 meV). However, the fabrication of the light emitting devices using ZnO homojunctions is suffered from the lack of reproducibility of the p-type ZnO with high hall concentration and mobility. Thus, the ZnO-based p-n heterojunction light emitting diode (LED) using p-Si and p-GaN would be expected to exhibit stable device performance compared to the homojunction LED. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducibleavailability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices with low defect density. However, the electroluminescence (EL) of the device using n-ZnO/p-GaN heterojunctions shows the blue and greenish emissions, which are attributed to the emission from the p-GaN and deep-level defects. In this work, the n-ZnO:Ga/p-GaN:Mg heterojunction light emitting diodes (LEDs) were fabricated at different growth temperatures and carrier concentrations in the n-type region. The effects of the growth temperature and carrier concentration on the electrical and emission properties were investigated. The I-V and the EL results showed that the device performance of the heterostructure LEDs, such as turn-on voltage and true ultraviolet emission, developed through the insertion of a thin intrinsic layer between n-ZnO:Ga and p-GaN:Mg. This observation was attributed to a lowering of the energy barriers for the supply of electrons and holes into intrinsic ZnO, and recombination in the intrinsic ZnO with the absence of deep level emission.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.50.1-50.1
• /
• 2009

Transparent conductive oxides (TCOs) play an important role in thin-film solar cells in terms of low cost and performance improvement. Al-doped ZnO (AZO) is a very promising material for thin-film solar cellfabrication because of the wide availability of its constituent raw materials and its low cost. In this study, AZO films were prepared by low pressurechemical vapor deposition (LPCVD) using trimethylaluminum (TMA), diethylzinc(DEZ), and water vapor. In order to improve the absorbance of light, atypical surface texturing method is wet etching of front electrode using chemical solution. Alternatively, LPCVD can create a rough surface during deposition. This "self-texturing" is a very useful technique, which can eliminate additional chemical texturing process. The introduction of a TMA doping source has a strong influence on resistivity and the diffusion of light in a wide wavelength range.The haze factor of AZO up to a value of 43 % at 600 nm was achieved without an additional surface texturing process by simple TMA doping. The use of AZO TCO resulted in energy conversion efficiencies of 7.7 % when it was applied to thep-i-n a-Si:H thin film solar cell, which was comparable to commercially available fluorine doped tin oxide ($SnO_2$:F).

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.512-519
• /
• 2001

Sink roll has been used in molten Zn-0.2%Al alloy bath of continuous galvanizing line in sinking and stabilizing process of the steel strip in molten metal bath. In this process, although the scraper scraps off the sink roll surface, the dross compounds is builded up on the sink roll surface and the life time of the sink roll is shorten by the dross compounds. The present study was investigated the application of the spray coating layer on sink roll body for improving durability In molten Zn-0.2%Al alloy. Through the durability tests in molten Zn-0.2%Al alloy with various ceramic and cermet coating layer, the optimum bond and top coating material was obtained. As the results, the system of STS430F base metal, WC-l7Co bond and $ZrO_2-SiO_2$ top coating was clarified to be the best quality of durability in molten Zn-0.2%Al alloy.

• 한국전기전자재료학회논문지
• /
• 제25권2호
• /
• pp.121-124
• /
• 2012

The characteristics of Ga-doped zinc oxide (GZO) thin films deposited at different deposition temperatures (TS~250 to $550^{\circ}C$) on 4H-SiC have been investigated. Structural and electrical properties of GZO thin film on n-type 4H-SiC(0001) were investigated by using x-ray diffraction(XRD), atomic force microscopy(AFM), Hall effect measurement, barrier height from I-V curve and Auger electron spectroscopy(AES). XRD $2\theta$ scan shows GZO thin film has preferential orientation with c-axis perpendicular to SiC substrate surface. The lowest resistivity ($\sim1.9{\times}10^{-4}{\Omega}cm$) was observed for the GZO thin film deposited at $400^{\circ}C$. As deposition temperature increases, barrier height between GZO and SiC was increased. Whereas, resistivity of GZO thin films as well as barrier height between GZO and SiC were increased after annealing process in air atmosphere. It has been found that the c-axis oriented crystalline quality as well as the relative amount of activated Ga3+ ions and oxygen vacancy may affect the electrical properties of GZO films on SiC.

• 센서학회지
• /
• 제19권6호
• /
• pp.462-468
• /
• 2010

A low power gas sensor with microheater was fabricated by MEMS technology. In order to heat up the gas sensing material to a operating temperature, a platinum(Pt) micro heater was built on to the micromachined Si substrate. The width and gap of microheater were $20\;{\mu}m$ and $4.5\;{\mu}m$, respectively. ZnO nanowhisker arrays were fabricated on a sensor device by hydrothermal method. The sensor device was deposited with ZnO seeds using PLD systems. A 200 ml aqueous solution of 0.1 mol zinc nitrate hexahydrate, 0.1 mol hexamethylenetetramine, and 0.02 mol polyethylenimine was used for growthing ZnO nanowhiskers. The power consumption to heat up the gas sensor to a operating temperature was measured and temperature distribution of sensor was analyzed by a Infrared Thermal Camera. The optimum temperature for highest sensitivity was found to be $250^{\circ}C$ although relatively high(64 %) sensitivity was obtained even at as low as $150^{\circ}C$. The power consumption was 72 mW at $250^{\circ}C$ and was only 25 mW at $150^{\circ}C$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.400-400
• /
• 2012

산화물 반도체는 넓은 에너지갭을 가지고 높은 이동성과 높은 투명성을 가지기 때문에 초고 속 박막 트랜지스터(Thin film transistor; TFT)에 많이 응용되고 있다. 그러나 ZnO 및 $In_2O_3$ 산화물 반도체를 박막트랜지스터에 사용할 경우 소자가 불안정하여 전기적 성질이 저하되고 문턱전압의 이동이 일어난다. TFT에 사용되는 산화물 반도체로는 GaInZnO, ZrInZnO, HfInZnO 및 GaSnZnO의 전기적 특성에 관한 연구가 많이 되었다. 그러나 titanium-indium-zinc-oxide (TIZO) TFT에 대한 연구는 비교적 적게 수행 되었다. 본 연구에서는 TFTs의 안정성을 향상하기 위하여 TFT의 채널로 사용되는 TiInZnO를 형성하는데 간단한 제조 공정과 낮은 비용의 용액 증착방법을 사용하였다. 졸-겔 전해액은 Titanium (IV) isopropoxide $[Ti(OCH(CH_3)_2)_4]$, 0.1 M Zinc acetate dihydrate $[Zn(CH_3COO)_2{\cdot}2H_2O]$ 그리고 indium nitrate hydrate $[In(NO_3)_3{\cdot}xH_2O]$을 2-methoxyethanol의 용액에 합성하였다. $70^{\circ}C$에서 한 시간 동안 혼합 하였다. Ti의 몰 비율은 10%, 20% 및 40% 로 각각 달리하여 제작하였다. $SiO_2$층 위에 2,500 rpm 속도로 25초 동안 스핀 코팅하여 TFT를 제작하였다. TIZO 박막에 대한 X-선 광전자 스펙트럼 관측 결과는 Ti 몰 비율이 증가함에 따라 Ti 2p1/2피크의 세기가 증가함을 보여주었다. TiZO 박막에 Ti 원자를 첨가하면 $O^{2-}$ 이온이 감소하기 때문에 전하의 농도가 변화하였다. 전하 농도의 변화는 TiZO 채널을 사용하여 제작한 TFT의 문턱전압을 양 방향으로 이동 하였으며 off-전류를 감소하였다. TiZO 채널을 사용하여 제작한 TFT의 드레인 전류-게이트 전압 특성은 on/off비율이 $0.21{\times}107$ 만큼 크며 이것은 TFT 소자로서 우수한 성능을 보여주고 있다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.59-59
• /
• 2010

ZnO는 II-VI 족 화합물 반도체로써 상온에서 큰 엑시톤 결합에너지 (~60 meV) 를 가지며 밴드갭이 3.37 eV인 직접 천이형 반도체로 잘 알려진 물질이다. 이러한 ZnO의 물리적 특성은 광학소자로 상용화된 GaN와 유사하기 때문에 LED나 LD등의 광 소자 재료로 주목 받고 있다. 또한 ZnO는 3족 원소 (In, Ga, Al)를 도핑 함으로써 전기적 특성 제어가 가능한 장점을 가지고 있다. 본 연구는 펄스레이저 증착법 (Pulsed Laser Deposition)을 이용하여 Si (111) 기판 위에 ZnO:In 박막을 성장 시켰으며, 도핑된 indium 양에 따른 ZnO 박막의 배향성 변화를 관찰 하였다. X-선 회절 분석법 (X-ray diffraction), 탐침형 원자현미경 (Atomic Force Microscope) 그리고 투과전자 현미경 (Transmission Electron Microscope)을 측정하였다. XRD 측정 결과 un-doped ZnO 박막은 (002) 방향으로 c-축 우선성장 하였다. 그러나 ZnO 박막내의 Indium 양이 증가 할수록 (002) 방향에서 (101), (102), (103) 등의 (101) 방향으로 성장이 변화 하였으며 5 at.% 이상에서는 (100) 방향의 성장이 관찰 되었다. TEM 측정 결과 un-doped ZnO 박막은 columnar 구조로 성장 되었으나, Indium 양이 증가할수록 column의 size가 감소하며, 5 at.% 이상에서 columnar 구조 성장이 거의 관찰되지 않는다. AFM 결과에서는 Indium 양이 증가 할수록 박막의 표면거칠기와 결정립 크기가 감소하였다.