• 한국주조공학회지
• /
• 제20권5호
• /
• pp.300-306
• /
• 2000

The objective of this work was to investigate the effects of SiC particle size(50, 100 ${\mu}m$) and additional elements such as Si, Cu and Ti on aging behavior in Al-5Mg-X(Si,Cu,Ti)/SiCp composites fabricated by pressureless infiltration method using hardness and wear test, scanning electron microscopy(SEM) and differential scanning calorimetry(DSC). The peak aging time in Al-5Mg-X(Si, Cu, Ti)/SiCp(50, 100 ${\mu}m$) composites is shorter than Al-5Mg-0.3Si alloy.The peak aging time of 50 ${\mu}m$ SiC particle reinforced Al-5Mg-X(Si,Cu,Ti) composites is shorter than those of 100 ${\mu}m$ SiC particle reinforced of Al-5Mg-X(Si,Cu,Ti) composites. The Al-5Mg-0.3Si-0.1Cu-0.1Ti/SiCp(50 ${\mu}m$) composites aged at $180^{\circ}C$ has higher hardness and better wear resistance than any other aged composite.The aging effect is promoted by the addition of Si and Cu in Al-5Mg/SiCp composites, so the wear resistance of Al-5Mg/SiCp composites with Si and Cu elements is enhanced by the aging treatment.

• 한국주조공학회지
• /
• 제13권4호
• /
• pp.350-358
• /
• 1993

Aluminum base composites reinforced with various amount of SiC particles and Mg contents have been investigated by different fabrication method for twenty-years. In this paper, how the decomposition and dissolution behaviors of $SiCp(20{\mu}m)$ in the melt of Al composites arised was studied. As the results, the decomposition and dissolution of SiCp into the melt of Al composites increased with increase of the temperature above $720^{\circ}C$, and holding time at a given melting temperature. Because SiC is thermodynamically unstable in this Al-SiCp composite at temperature above the liquidus, SiCp dissolves and reacts with Al in matrix to form $Al_4C_3$ according to following chemical equation $4Al+3SiC{\rightarrow}Al_4C_3+3Si$, Si decomposed and dissolved from SiCp increases Si content of matrix, while liquidus temperature of matrix decrease with increase of SiC content in matrix. The hardness of SiCp decreased with increase of the melting temperature, the hardness of the matrix /particle interface increased with increase of the melting temperature due to increase of the $Mg_2Si$ and $Al_4C_3$ intermetallic compounds, etc.

• 한국주조공학회지
• /
• 제11권1호
• /
• pp.71-78
• /
• 1991

Microstructure and characteristics of the SiCp/Al-4.5wt%Cu-1wt%Mg composites fabricated by the combination of the compocasting and the pressurized continuous casting process, which is one of the processes to decrease the limitations of the size, and shops of the products, are investigated. The main results are as follows: 1) the SiCp/Al alloy matrix composites can be made continuously 2) as the amount of SiCp addition increases; (1) the degree of directional solidification of matrix structure decreases, and that of SiCp dispersion improves, (2) wear resistance improves, and especially these composites show the excellent wear resistance under the high sliding speed and high final load condition, (3) wear mechanism of these composites is changed from adhesive wear into abrasive wear, and the tendency of that becomes outstanding with increasing sliding speed.

• 한국재료학회지
• /
• 제11권7호
• /
• pp.590-598
• /
• 2001

본 연구에서는 특별하게 고안된 In-situ VHP 제조 공정을 이용하여 상온에서 $500^{\circ}C$까지의 진공 열간 압축과 canning 작업 없이 $520^{\circ}C$에서 연속 압출옳 하여 Sicp/pure Al과 SiCp/2024Al MMCs를 제조하였다. 복합재료의 인장강도와 미세구조에 영향을 주는 SiC 입자크기, 체적률, 압출비에 대해서 조사하였다. 압출비 10:1의 경우에는 SiCp/pure Al과 SiCp/2024Al 복합재료 둘 다 건전한 외형과 SiCp의 일정한 분산을 가지면서 SiCp의 균열이 없는 좋은 미세 구조를 가지고 있었다. 그러나 압출비 16:1의 경우에는 체적률이 증가할수록 파괴된 SiC 입자의 수가 증가하였으며 2024Al 기지내의 복합재료와 순수한 Al 기지재 복합재료를 서로 비교하였다. 동일한 체적률과 압출비의 경우에는 SiCp의 크기가 작은 복합재료가 SiCp가 큰 복합재료보다 인장강도가 더 높았다.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.122-131
• /
• 1995

The research trends for metal matrix composites have been on basic mechanical properties, fatigue behavior after aging and fractographic observations. In this study, the fatigue crack initiation as well as the fatigue crack growth behavior and the fracture mechanism were investigated through observations of the fracture surface on silicon carbide particles reinforced aluminum metal matrix composites(SiCp/Al). Based on the fractographic study done by scanning electron microscope and replica, crack growth path model and fracture mechanism are presented. The mechanical properties, such as the tensile strength, yield strength and elongation of SiCp/Al composites are improved in a longitudinal direction, however, the fatigue life is shorter than the basic Al6061 alloys. From fractographic observations, it is found that the failure mode is ductile in basic Ai6061 alloys. And because some SiC particles were pulled out from the matrix and a few SiC particles could be seen on the fracture surface of SiCp/Al, crack growth paths are believed to follow the interface of the matrix and its particles.

• 한국주조공학회지
• /
• 제20권6호
• /
• pp.377-385
• /
• 2000

Al matrix composites as the most promising MMCs can be expected to be excellent engineering materials in the nearest future. So as to improve material properties of composite, many manufacturing processes have been developed. Among them, squeeze casting process which offers fine microstructure and near-net-shape is one of the most successful MMCs manufacturing processes. But, in case of with subsieve size particles (under 44 ${\mu}m$), it is very difficult to homogeneously distribute particles in matrix of Al matrix composite by various casting processes, including squeeze casting used so far. Duplex process which was developed in previous study was used to distribute the particle of subsieve size more homogeneously in matrix of Al matrix composite. Microstructures, wear and heat resistance characterization of Al-Si-Cu-Mg-(Ni)/SiCp manufactured by duplex process were examined to clarify the effect of manufacturing conditions, particle size of reinforcement and alloying elements. Al matrix composites reinforced with SiCp(10 ${\mu}m$) have the lowest wear amount among composites reinforced with 3 ${\mu}m$, 5 ${\mu}m$ and 10 ${\mu}m$ SiCp. The wear amount of Al matrix composites with 10 wt.% SiCp(3, 5, 10 ${\mu}m$) was decreased according to the increase of the sliding speed because abrasive wear takes place at high sliding speed of 4m/s and worn debris with block type occurs at low sliding speed of 1m/s. As for heat resistance, it is made clear that remarkable heat resistance property can be obtained by addition of Ni element in Al matrix composites.

• 한국주조공학회지
• /
• 제21권1호
• /
• pp.7-14
• /
• 2001

The research on new DRA(discontinuous reinforced alloy) and CRA(continous reinforced alloy) composites has been carried out to improve the properties of ceramic fiber and particle reinforced metal matrix composites(MMCs). Effects of alloying elements and aging conditions on the microstructures and aging behavior of Al-Si-Cu-Mg-(Ni)-SiCp composite have been examined. The specimens used in this study were manufactured by duplex process. The first squeeze casting is the process to make precomposite and the second squeeze casting is the process to make final composite. The hardening behavior was accelerated with decreasing the size of SiCp particle in the composites. It is considered that the dislocation density increased with increasing SiCp size, due to the different thermal deformation between Al matrix and SiCp during quenching after the solution treatment. Peak aging time to obtain the maximum hardness in 3 ${\mu}m$ SiCp reinforced Al composite was reduced than that in large size(5, 10 ${\mu}m$) of SiCp because of difference in dislocation density. Aging hardening responce(${\Delta}H$ = $H_{Max}.-H_{S.T}$) of composites was greater than that of unreinforced Al alloy because of higher density of second phases in matrix.

• 한국주조공학회지
• /
• 제13권6호
• /
• pp.524-531
• /
• 1993

Dispersion behaviors of SiC particles and microstructures in Al-2%Si/SiCp composite prepared by Rheo-compocasting were studied with change of fabrication conditions(slurry temperature, agitation time) and additions of Mg($0{\sim}3wt.%$). Also, the microhardness change of matrix, interface and total in composites were examined with additions of Mg($0{\sim}3wt.%$). The dispersion of particles in the composites became relatively homogeneous with increase of Mg additions, agitation time and decrease of slurry temperature. Rate of occupied area by particle in matrix was increased as increase of Mg additions due to improvement of wettability between SiC particle and matrix. A favorable composites were obtained by melting under Ar atmospheric SiCp injection and bottom pouring system. According to the analysis of X-ray diffraction, $Mg_2Si$, $Al_4C_3$, $SiO_2$ and MgO, etc, intermetallic compounds were formed by chemical interreaction at interface of matrix and particles. The microhardness of interface is higher than that of matrix due to more strengthening of above intermetallic compounds. It was considered that the total hardness of the composites is improved by dispersing of SiCp and addition of Mg.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.190-194
• /
• 2000

The fabrication process and thermal properties of 50∼76vo1% SiCp/Al metal matrix composites (MMCs) were investigated. The 50∼76vo1% SiCp/Al MMCs fabricated by pressure infiltration casting process showed that thermal conductivities were 85∼170W/mK and coefficient of thermal expansion (CTE) were ranged 10∼6ppm/K. Specially, the thermal conductivity and CTE of 71vo1%SiCp/Al MMCs were ranged l15∼156W/mK and 6∼7ppm/K, respectively, which showed a improved thermal properties than the conventional electronic packaging materials such as ceramics and metals.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.83-87
• /
• 1999

The fabrication process and thermal properties of 50~71vol% SiCp/Al metal matrix composites (MMCs) were investigated. The 50~71vol% SiCp/Al MMCs fabricated by pressure infiltration casting process showed that thermal conductivities were 118~170W/mK and coefficient of thermal expansion (CTE) were 9.5~$6.5{\times}10^{-6}/K$. Specially, the thermal conductivity and CTE of 71vol%SiCp/Al MMCs were 115~156W/mK and 6~$7{\times}10^{-6}/K$. respectively, which showed a improved themal properties than the conventional electronic packaging materials such as ceramics and metals.