• Transactions on Electrical and Electronic Materials
• /
• v.1 no.4
• /
• pp.11-15
• /
• 2000

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR(DLAR) coating of MgFe$_2$/GeO$_2$. We investigated GeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown GeO$_2$ film showed deposition temperature strong dependence. The GeO$_2$ at 400$\^{C}$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgFe$_2$film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4 ㎛ to 1.1 ㎛. Solar cells with a structure of MgFe$_2$/GeO$_2$/Ag/N$\^$+//p-type Si/P$\^$+//Al were investigated with the without DLAR coatings. We achieved the efficiency of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details about MgFe$_2$,GeO$_2$ films, and cell fabrication parameters are presented in this paper.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.4
• /
• pp.145-150
• /
• 2007

The $SiO_2$ and $TiO_2$ thin films for the multilayer interference filter application were manufactured by electron beam process. In case of electron beam process with ion source, the anode current was controlled by gas volume ratio of $O_2$ and Ar. Substrate temperature of electron beam deposition without ion source was increased from 100 to $250^{\circ}C$ with $50^{\circ}C$ increment. The surface roughness values of $SiO_2$ thin films was most low value at $200^{\circ}C$ substrate temperature and 0.2 A anode current respectively. And the surface roughness values of $TiO_2$ thin films was most low value at room temperature and 0.2 A anode current repectively. The refractive index of $SiO_2$ and $TiO_2$ thin films to be deposited with ion source was usually lower than that of thin films without ion source.

• Journal of the Korean Vacuum Society
• /
• v.13 no.3
• /
• pp.114-119
• /
• 2004

Silicon Nitride thin films were deposited on p-type Si (100) substrates by atomic layer deposition (ALD) method at $550^{\circ}C$ using alternating exposures of $SiH_2Cl_2$ and $NH_3$, and the physical and electrical propeties of the deposited films were characterized. The thickness of the films was linearly increased with the number of deposition cycles, and the growth rate of the films was 0.13 nm/cycle with the reactant exposures of $3.0\times10^{9}$ L. The silicon nitride thin films deposited by Alf exhibited similar physical properties with the silicon nitride thin films deposited by low-pressure chemical vapor deposition (LPCVD) method in terms of refractive index and wet etch rate, lowering deposition temperature by more than 200 $^{\circ}C$. The ALD films showed the leakage current density of 0.79 nA/$\textrm{cm}^2$ at 3 MV/cm, which is lower than 6.95 nA/$\textrm{cm}^2$ of the LPCVD films under the same condition.

• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.821-827
• /
• 2004

Titanium oxide thin films were prepared on Si(100) substrates by R.F. magnetron reactive sputtering at $30\sim200watt$ R.F power range, and annealed at $600^{\circ}C\sim800^{\circ}C$ for 1 hour. The properties of $TiO_2$ thin films were analyzed using x-ray, ${\alpha}-step$, ellipsometer, scanning electron microscopy, and FT-IR spectrometer. Upon in-situ depositions, the initial phase of $TiO_2$ thin film showed non-crystalline phase at R.F. power $30\sim100$ watt. The crosssection of $TiO_2$ thin films were sbserved to be the columnar structure. With the increasing R.F power and annealing temperature, the grain size, crystallinity, refractive index, and void size of titanium oxides showed a tended to increase. The FT-IR transmittance spectra of titanium oxide thin films have the obsorption band of Ti-O bond, Si-O bond, Si-O-Ti bond and O-H bond. With the increase of R.F. power and annealing temperature, these films have the stronger bond structures. It is considered that such a phenomena is due to phase transition and good crystallinity

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.149-149
• /
• 2010

The double-layer antireflection (DLAR) coatings have significant advantages over single-layer antireflection (SLAR) coatings. This is because they will be able to cover a broad range of the solar spectrum which would enhance the overall performance of solar cells. Moreover films deposited at high frequency are expected to show excellent and UV-stable passivation in the refractive index that we adopted. In this work, we present a novel DLAR coating using SiNx:H thin films with refractive indices 1.9 and 2.3 as the top and bottom layers. This approach is cost effective when compared to earlier DLAR coatings with two different materials. SiNx:H films were deposited by Plasma enhanced chemical vapor deposition (PECVD) technique using $SiH_4$, $NH_3$ and $N_2$ gases with flow rates 20~80sccm, 200sccm and 85 sccm respectively. The RF power, plasma frequency and substrate temperature for the deposition were 300W, 13.56 MHz and $450^{\circ}C$, respectively. The optimum thickness and refractive indices values for DLAR coatings were estimated theoretically using Macleod simulation software as 82.24 nm for 1.9 and 68.58 nm for 2.3 respectively. Solar cells were fabricated with SLAR and DLAR coatings of SiNx:H films and compared the cell efficacy. SiNx:H> films deposited at a substrate temperature of $450^{\circ}C$ and that at 300 W power showed best effective minority carrier lifetime around $50.8\;{\mu}s$. Average reflectance values of SLAR coatings with refractive indices 1.9, 2.05 and 2.3 were 10.1%, 9.66% and 9.33% respectively. In contrast, optimized DLAR coating showed a reflectance value as low as 8.98% in the wavelength range 300nm - 1100nm.

• Food Science and Preservation
• /
• v.8 no.1
• /
• pp.47-53
• /
• 2001

In order to investigate the effect of two type of ceramic film(15% SiO$_2$ incorporated LDPE, 10% zeolite incorporated LDPE), perforated film and LDPE film on freshness of shiitake mushroom, weight loss, surface color and marketability of mushroom were measured during MA storage at 5 $\^{C}$ and 20$\^{C}$. The effect of packaging films on weight loss and marketability index of shiitake mushroom at 20$\^{C}$ was negligible due to its rapid physiological changes. However, the effect of packaging films on surface color of shiitake mushroom was significant at 20$\^{C}$ storage, but not at 5$\^{C}$ storage. During MA storage of shiitake mushroon, discoloration were reduced effectively by ceramic films and weight loss were by LDPE film, but they had little difference between packaging 51ms. However, there were significant differences among the packaging films in marketability of mushroom induced by water vapor inside package and accelerate its spoilage and browning. Ceramic film(15% SiO$_2$ incorporated LDPE) showed best result to maintain marketability of shiitake mushroom and zeolite incorporated film, perforated film, LDPE film in order.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.961-968
• /
• 1998

In order to investigate the effects of substrate bias voltage on the formation of$ZnS-SiO_2$ protective film in phase change optical disk by R.F. magnetron sputtering method, thin dielectric film was formed on Si wafer and Corning glass by using ZnS(80mol%)-$SiO_2$(20mol%)t arget under argon gas. In this study, the Taguchi experimental method was applied in order to obtain optimum conditions with reduced number of experiments and to control numerous variables effectively. At the same time this method can assure the reproducibility of experiments. Optimum conditions for film formation obtained by above method were target RF power of 200 W. substrate RF power of 20 W, Ar pressure of 5 mTorr. sputtering time of 20 min.. respectively. The phase of specimen was determined by using XRD and TEM. The compositional analysis of specimen was performed by XPS test. In order to measure the thermal resistivity of deposited specimen, annealing test was carried out at $300^{\circ}C$ and $600^{\circ}C$. For the account of void fraction in thin film, the Bruggeman EMA(Effective Medium Approximation) method was applied using the optical data obtained by Spectroscopic Ellipsometry. According to the results of this work, the existence of strong interaction between bias voltage and sputtering time was confirmed for refractive index value. According to XRD and TEM analysis of specimen, the film structure formed in bias voltage resulted in more refined structures than that formed without bias voltage. But excess bias voltage resulted in grain growth in thin film. It was confirmed that the application of optimum bias voltage increased film density by reduction of void fraction of about 3.7%.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.479-483
• /
• 2002

Silicon dioxide thick film using silica optical waveguide cladding was fabricated by Plasma Enhanced Chemical Vapor Deposition(PECVD) method, at a low temperature ($320^{\circ}$C) and from $(SiH_4+N_2O)$ gas mixtures. The effects of deposition parameters on properties of $SiO_2$ thick films were investigated by variation of $N_2O/SiH_4$ flow ratio and RF power. After the deposition process, the samples were annealed in a furnace at $1150^{\circ}$C, in N2 atmosphere, for 2h. As the $N_2O/SiH_4$ flow ratio increased, deposition rate decreased from 9.4 to 2.9 ${\mu}m/h$. As the RF power increased, deposition rate increased from 4.7 to 6.9 ${\mu}m/h$. The thickness and the refractive index measurements were measured by prism coupler. X-ray Photoelectron Spectroscopy(XPS) and Fourier Transform-infrared Spectroscopy(FT-IR) were used to determine the chemical states. The cross-section of films was observed by Scanning Electron Microscopy(SEM).

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.341-345
• /
• 2000

We investigated the microstructures and the electrical properties of $ZrO_2$thin films deposited by reactive DC magnetron sputtering on (100) Si with different deposition conditions and annealing treatments. The refractive index of the $ZrO_2$ thin films increased with annealing temperatures and deposition powers, and approached to the ideal value of 2.0~2.2. The $ZrO_2$thin films deposited at the room temperature are amorphous, and the films are polycrystalline at the deposition temperature of $300^{\circ}C$. Both the thickness of the interfacial oxide layer and the root-mean-square (RMS) value of surface roughness increased upon annealing in the oxygen ambient. The Cmax value and leakage current value decreased with the increase of thickness of the interfacial oxide thickness.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.40-47
• /
• 2014

In this paper, $Al_2O_3$ film deposited by thermal atomic layer deposition (ALD) with diluted $NH_4OH$ instead of $H_2O$ was suggested for passivation layer and anti-reflection (AR) coating of the p-type crystalline Si (c-Si) solar cell application. It was confirmed that the deposition rate and refractive index of $Al_2O_3$ film was proportional to the $NH_4OH$ concentration. $Al_2O_3$ film deposited with 5 % $NH_4OH$ has the greatest negative fixed oxide charge density ($Q_f$), which can be explained by aluminum vacancies ($V_{Al}$) or oxygen interstitials ($O_i$) under O-rich condition. $Al_2O_3$ film deposited with $NH_4OH$ 5 % condition also shows lower interface trap density ($D_{it}$) distribution than those of other conditions. At $NH_4OH$ 5 % condition, moreover, $Al_2O_3$ film shows the highest excess carrier lifetime (${\tau}_{PCD}$) and the lowest surface recombination velocity ($S_{eff}$), which are linked with its passivation properties. The proposed $Al_2O_3$ film deposited with diluted $NH_4OH$ is very promising for passivation layer and AR coating of the p-type c-Si solar cell.