• Journal of the Korean Ceramic Society
• /
• v.47 no.4
• /
• pp.325-328
• /
• 2010

Varying quantities of a high-thermal-expansion glass, 50CaO-20ZnO-$20B_2O_3-10SiO_2$ (CZBS), were added to alumina and sintered at $875^{\circ}C$ for 2 h for low temperature co-firing ceramic (LTCC) applications. As the amount of glass addition increased from 40 wt% to 70 wt%, the apparent density of the sintered product increased from 88.8% to 91.5%, which was also qualitatively confirmed by microstructural observation. When the glass addition was very high, e.g., 70 wt%, an apparent formation of secondary phases such as $CaZn_2AlZnSiAlO_7$, $Ca_2Al(AlSi)O_7$, $Ca_2Al_2SiO_7$, $Ca_2ZnSi_2O_7$ and ZnO, was observed. Both the dielectric constant and the coefficient of thermal expansion increased with the glass addition, which was qualitatively consistent with the analytical models, while the experimental values were lower than the predicted ones due to the presence of pores and secondary phases.

• Advanced Composite Materials
• /
• v.17 no.1
• /
• pp.75-87
• /
• 2008

Aerospace structural applications, along with high performance marine and automotive applications, require high-strength efficiency, which can be achieved using metal matrix composites (MMCs). Rotating components, such as jet-engine blades and gas turbine parts, require materials that maximize strength efficiency and metallurgical stability at elevated temperatures. Titanium matrix composites (TMCs) are well suited in such applications, since they offer an enhanced resistance to temperature effects as well as corrosion resistance, in addition to optimum strength efficiency. The overall behavior of the composite system largly depends on the properties of the interface between fiber and matrix. Characterization of the fiber.matrix interface at operating temperatures is therefore essential for the developemt of these materials. The fiber fragmentation test shows good reproducibility of results in determining interface properties. This paper deals with the evaluation of fiber fragmentation characteristics in TMCs at elevated temperature and the results are compared with tests at ambient temperature. It was observed that tensile testing at $650^{\circ}C$ of single-fiber TMCs led to limited fiber fragmentation behavior. This indicates that the load transfer from the matrix to the fiber occurs due to interfacial friction, arising predominantly from mechanical clamping of the fiber by radial compressive residual and Poisson stresses. The present work also demonstrates that composite processing conditions can significantly affect the nature of the fiber.matrix interface and the resulting fragmentation of the fiber.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.111-114
• /
• 2001

This paper presents the influence of the additive composition on flexural strength and hardness of SiC-TiC composites materials for spectacle lens cutting materials. The materials were hot-pressed at $1800^{\circ}C$ and subsequently annealed at $1910^{\circ}C$ for 3h. The heating rate was $15^{\circ}C/min$ and the cooling rate about $25^{\circ}C/min$ in from the sintering temperature to $1300^{\circ}C$. The growth of particles of spectacle lens cutting materials was analysed by SEM and crystalline phases were discussed by x-ray diffractometry. Typical fracture toughness and hardness of materials for spectacle lens cutting were $6.1MPa{\cdot}m^{1/2}$ and 14.9 GPa, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.309-309
• /
• 2007

The LTCCs (low-temperature co-fired ceramics) are very important for electronic industry to build smaller RF modules and to fulfill the necessity for miniaturization of devices in wireless communication industry. The dielectric materials with sintering temperature $T_{sint}$<$900^{\circ}C$ are required. In this study, we investigated with glass-ceramic composition, which was crystallized with two crystals. The microstructure, crystal phases, thermal and mechanical properties, and dielectric properties of the composites were investigated using FE-SEM, XRD, TG-DTA, 4-point bending strength test and LCR measurement. The starting temperature for densification of a sintered body was at $779{\sim}844^{\circ}C$ and the glass frits were formatted to the crystal phases, $CaAl_2Si_2O_8$(anorthite) and $CaMgSi_O_6$(diopside), at sintering temperature. The sintered bodies exhibited applicable dielectric properties, namely 6-9 for ${\varepsilon}_r$. The results suggest that the glass-ceramic composite would be potentially possible to application of low dielectric L TCC materials.

• Elastomers and Composites
• /
• v.31 no.5
• /
• pp.335-340
• /
• 1996

In order to look into the internal structure and the properties in the silicone rubbers added reinforcing fillers; silica $additives(O{\sim}140phr)$, and to examine the behavior of charged particles, the properties of thermally stimulated current(TSC) and X-Ray diffraction are investigated, respectively. And then, from the TSC which are formed by applying the electric field of $2{\sim}5kV/mm$ to specimen at the temperature range from -150 to $260^{\circ}C$, the results are as follwing: In the case of non-filled specimen, four peaks of ${\delta},\;{\gamma},\;{\beta}\;and\;{\alpha}$ are obtained at the temperature of $-120^{\circ}C,\;-60^{\circ}C,\;20^{\circ}C\;and\;130^{\circ}C$, respectively and the case of filled specimen, three peaks of ${\delta},\;{\alpha}_2\;and\;{\alpha}_1$ are observed at the temperature of $-120^{\circ}C,\;80^{\circ}C\;and\;130^{\circ}C$, respectively. The origins of these peaks are that, the ${\delta}$ peak seems to the result from the contribution of side chain methyl radical, and the ${\gamma}$ peak from the depolarization of space charge polarization owing to be added impurity during manufacturing specimens, and the ${\beta}$ peak from the orientation of $Si-CH_3$ dipole, and the ${\alpha}_2$ near the temperature of $80^{\circ}C$ from hydroxyl in carboxylic radical, and finally, the ${\alpha}_1$ peak near the temperature of $130^{\circ}C$ from carboxyl acid that is formed by the thermal oxidation of high temperature.

• Journal of Korea Foundry Society
• /
• v.20 no.1
• /
• pp.21-28
• /
• 2000

Ni and Ni-Cr porous metals which are estimated to be easy to fabricate by squeeze casting are used as strengtheners for composite materials. As a matrix material, Al-7%wtSi-0.3 wt%Mg(AC4C) has been used. In case of Ni/AC4C and Ni-Cr/AC4C composite, $750^{\circ}C$ melt temperature and minimum 25 MPa squeezing pressure are needed to produce sound composite materials. The observation of interfacial reaction zone at various heat treatment condition showed that solutionizing temperature of above 520^{\circ}C$, the interfacial reaction zone increased proportionally with increasing heat treatment tim and reaction products formed by interfacial reaction are mainly composed of $Al_3Ni$ and $Al_3Ni_2$ phases. The tensile strength of Ni/AC4C and Ni-Cr/AC4C composite is lower than the matrix metal and this can be explained by the brittle intermetallic compounds formed at the interface of Ni and Ni-Cr reinforcements. But the properies of hardness, wear resistance and thermal expansion are better than the matrix due to the strengthening effect of Ni-Cr porous metals.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.7
• /
• pp.953-956
• /
• 2003

Hexagonal GaN (h-GaN) films have been grown on Si(111) substrates by metal organic chemical vapor deposition using the azidodiethylgallium methylamine adduct, Et₂Ga(N₃)·NH₂Me, as a new single precursor. Deposition was carried out in the substrate temperature range 385-650 °C. The GaN films obtained were stoichiometric and did not contain any appreciable amounts of carbon impurities. It was also found that the GaN films deposited on Si(111) had the [0001] preferred orientation. The photoluminescence spectrum of a GaN film showed a band edge emission peak characteristic of h-GaN at 378 nm.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.572-580
• /
• 2003

Synthesizing behavior and microstructural evolution of $CaZrO_3$and $m-ZrO_2$in a thermal reaction process of $ZrSiO_4$-$xCaCO_3$mixtures, where x is 7 and 19, were investigated to determine the addition amount of CaO in CaO:$ZrO_2$:$SiO_2$ternary composition. CaZrO$_3$-Ca$_2$SiO$_4$precursor prepared by the mixture of $ZrSiO_4$and CaCO$_3$in aqueous suspending media was controlled to the acidic (pH=4.0) condition with HCI solution to enhance the thermal reaction. The addition amount of dispersant into the $ZrSiO_4$-$xCaCO_3$slip increased with increasing mole ratio of $CaCO_3$, which was associated with the viscosity of slip. Decarbonation reaction was activated with an increase of the addition amount of $CaCO_3$, showing different final temperatures in $ZrSiO_4$-$7CaCO_3$and $ZrSiO_4$-$19CaCO_3$mixtures as about 980 and 116$0^{\circ}C$, respectively, for finishing decarbonation reaction. The grain morphology was changed to spherical shape for all samples with an increase of sintering temperature. The grain size and phase composition of the synthesized composites depended on the mixture ratio of Zrsi04 and CacO3 powders, indicating that the main crystals were m-ZrO2 ($\leq$3 $\mu\textrm{m}$) and $CaZrO_3$ ($\leq$ 7 $\mu\textrm{m}$) in $ZrSiO_4$$>-7CaCO_3$and $ZrSiO_4$-$19CaCO_3$mixtures, respectively.

• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.206-212
• /
• 1994

Aluminium titanate-mullite composites with varying chemical compositions were prepared by the stepwise hydrolysis of $Si(OC_2H_5)_4$, and $Ti(OC_2H_5)_4$in $AI_2O_3$ ethanolic colloidal dispersion. Sintered bodies having 20-50~01% mullite at $1600^{\circ}C$ for 2h have shown, that it is possible to develop an aluminium titanate with moderately high strength and low thermal expansion coefficient. This was obtained by inhibiting grain site of aluminium titanate with mullite and microcracks. Those with 80-70vol % aluminium titanate have excellent thermal shock resistance and has room-temperature strengths of 31-45MPa. The relation between thermal shock resistance and strength, Young's modulus, sound velocity and thermal expansion coefficient was discussed.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.370-376
• /
• 1998

Mechanical properties of PVC[poly(vinylchloride)] composites containing the dust from blast and converter (Kwangyang Iron Co.) were investigated as a function of dust content. Tensile strength is increased, when the blast dust is mixed with PVC to the extent of 8.83wt % and impact strength is not significantly changed. From these results, it is suggested that blast dust containing CaO, SiO, MgO, $A1_2O_3$ and metallugical particle is compatible with PVC. Thermogravimetric analysis(TGA) showed that residual weight(%) at temperature $600^{\circ}C$ increased with the amount of blast dust and differential scanning calorimetry(DCS) showed that the thermal stability of PVC composite was increased when the weight ratio of blast dust was 8.83wt % X-ray diffractometry measurement also showed their blends and structures.