• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.9-14
• /
• 2004

In this study, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ ammonium persulfate(AP)/isopropyl alcohol(IPA) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-unifonnity exists on the etched surface because of formation of hillocks on the (100) surface. The addition of IPA to TMAH solution leads to smoother etched surfaces but, makes the Si etch rate lower. However, with the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square membranes of 20${\mu}{\textrm}{m}$ thickness and l00-400${\mu}{\textrm}{m}$ one-side length were fabricated successfully by applying optimum Si etching conditions of TMAH/AP solutions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.416-417
• /
• 2005

In this study, we optimized the process of Si anisotropy etching by combing tetramethyl ammonium hydroxide (TMAH) etching process with ultrasonic wave technology. New ultrasonic TMAH etching apparatus was developed and it was used for fabricating a $20{\mu}m$ thick diaphragm for Si piezoresistive pressure sensors. Based on comparison study on etch rate and surface flatness, it was observed that the Si anisotropy etching methode with new ultrasonic TMAH etching apparatus (at 40 kHz/ 500 watt) was superior to conventional etching methods with TMAH or TMAH+ammonium persulfate(AP) solutions.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1033-1036
• /
• 2003

In this paper, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ ammonium persulfate (AP) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-uniformity exists on the etched surface because of formation of hillocks on the <100> surface. With the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square diaphragms of 20${\mu}{\textrm}{m}$ thickness and 100~400${\mu}{\textrm}{m}$ one-side length were fabricated successfully by applying optimum Si etching conditions of TMAH/AP solutions.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.4
• /
• pp.19-22
• /
• 2003

In this paper, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ammonium persulfate (AP) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-uniformity exists on the etched surface because of formation of hillocks on the <100> surface. With the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square diaphragms of 20$\mu\textrm{m}$ thickness and 100-400 $\mu\textrm{m}$ one-side length were fabricated successfully by adding AP of (5/6)g to 800 ml TMAH solution every 10 minutes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.162-163
• /
• 2007

The dry etching of Si was investigated using direct dc biasing to the Si substrate. The TCP type etching system with a feed-through for applying a dc bias was used in the etching. The applied dc bias and ICP power was varied to examine the effect on the etching at the fixed chamber pressure and $SF_6$ flow rate of 10 mTorr and 10 sccm during. When the plasma was generated at ICP power of 100 W, the etch rate of Si was increased with the bias for the biased samples. However, the etching of Si for the non-biased sample was enhanced for the increased ICP power.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1428-1430
• /
• 1995

In this study we fabricate Knife type Si-tip array using (110) Si wafer. We can fabricate vertical structure by anisotropic etching using EPW and observe it by SEM. After the step, we perform isotropic etching and oxidation sharpening of the structure and also observe it by SEM, respectively. The purpose of isotropic etching is to reduce the oxidation time. We attain a optimal tip whose radius is about $100{\AA}$ after anisotropic etching 2.25 min.+isotropic etching 5 min.+oxidation 1 hour and 23 min.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1686-1690
• /
• 1989

Using the anisotropic etching characteristics of N2H4-H2O solutions, Si diaphragm was fabricated for the integrated sensors. The optimal composition and temperature of the etching solution in (100) Si etching process was established to be 50mol% N2H4 in H2O at 105\ulcorner\ulcorner for both higher etch rate (=2.6\ulcorner/min) and better surface quality of etched (100) planes. Based on the above optimal etching condition, the electrochemical etch-stop technique was employed to form n-type Si diaphragm having a thickness of 20\ulcorner and the thickness of diapragm could exactly be controlled to 20\ulcorner\ulcorner.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.516-521
• /
• 2001

Dry etching of Si wafer and $SiO_2$ layers was performed using He/Cl$_2$ mixture plasma by diode-type reactive ion etcher (RIE) system. For Si etching, the Cl molecules react with the Si molecules on the surface and become chemically stable, indicating that the reactants need energetic ion bombardment. During the ion assisted desorption, energetic ions would damage the photoresist (PR) and produce the bad etch Si-profile. Moreover, we have examined the characteristics of the Cl-Si reaction system, and developed the new fabrication procedures with a $Cl_2$/He mixture for Si and $SiO_2$-etching. The developed novel fabrication procedure allows the RIE to be unexpensive and useful a Si deep etching system. Since the etch rate was proved to increase linearly with fHe and the selectivity of Si to $SiO_2$ etch rate was observed to be inversely proportional to fHe.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.63-69
• /
• 1999

The characteristic parameters of high density plasma source (Helical Resonator) have been measured with Langmuir probe to get the plasma density electron temperature, ion current density, etc. Optical emission spectra of Si and SiCl have been analyzed in $Cl_2$$/poly-Si system to elucidate etching mechanism. In this system, the main reaction to remove silicon atoms on the surface is proceeding mostly through chemical reaction, not pure physical reaction. The emission intensity of SiCl (chemical etching product) increases much faster than Si (pure physical etching product) with increasing the concentration of impurities (P). This is due to the electron transfer from substrate to the surface via Si-Cl bond. As a result, Si-Cl bond becomes more ionic and mobile, therefore the Cl-containing etchant forms $SiCl_x$ with surface more easily. Consequently, for the removal of Si atom from poly silicon surface, the chemical etching is more favorable than physical etching with increasing P concentrations.

• Journal of Powder Materials
• /
• v.22 no.1
• /
• pp.15-20
• /
• 2015

The composite of porous silicon (Si) and amorphous carbon (C) is prepared by pyrolysis of a nano-porous Si + pitch mixture. The nano-porous Si is prepared by mechanical milling of magnesium powder with silicon monoxide (SiO) followed by removal of MgO with hydrochloric acid (etching process). The Brunauer-Emmett-Teller (BET) surface area of porous Si ($64.52m^2g^{-1}$) is much higher than that before etching Si/MgO ($4.28m^2g^{-1}$) which indicates pores are formed in Si after the etching process. Cycling stability is examined for the nano-porous Si + C composite and the result is compared with the composite of nonporous Si + C. The capacity retention of the former composite is 59.6% after 50 charge/discharge cycles while the latter shows only 28.0%. The pores of Si formed after the etching process is believed to accommodate large volumetric change of Si during charging and discharging process.