• Journal of Welding and Joining
• /
• v.16 no.2
• /
• pp.93-99
• /
• 1998

The effects of welding conditions of gas metal arc welding on the elements loss of solid wire, oxygen content and impact toughness of weld metals were studied. Deoxidizing elements loss was increased with increase of arc voltage in both short-circuit transfer mode and globular transfer mode. It is believed that increase of arc voltage results in increase of reaction time between elements in the droplet and surrounding gas at the end of wire and in the arc column. Based on the thermodynamic equilibrium model, the oxygen content of weld metal can be predicted with the content of silicon and manganese as following : [%O] = $K([%Si][%Mn])^{-0.25}$, K = -15518/T+6.01. The equilibrium temperature was dependent on shielding gas, and it was 187$0^{\circ}C$ for $CO_2$ gas and 180$0^{\circ}C$ for 20%$CO_2$-80%Ar gas. The oxygen content of weld metal which shows maximum impact toughness was varied with deoxidizing alloy system of wires, 0.041 wt% for Si-Mn type wire and 0.026 wt% for Si-Mn-Ti type wire.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.298-307
• /
• 2019

Two types of CaO-Al₂O₃-SiO₂ (CAS) glass powder applied spray coating on the surface of sintered Al₂O₃ were researched for sintering behavior; (1) Si-rich, glass containing high content SiO₂, (2) Ca-rich, containing high content CaO. Foaming of bubbles remaining inside the Ca-rich glass was produced at a viscosity of approximately 10⁷~10⁹ poise, resulting in decreasing shrinkage (interfering with sintering) and increasing surface roughness. In case of Si-rich glass, there was no serious foaming bubbles phenomenon like Ca-rich below 1000℃, however cristobalite crystals with low density occurred at 1200℃ and then produced re-foaming of bubbles, resulting in abnormal sintering behavior. These phenomenon is considered to be a decrease in viscosity due to an increase in the Ca content of the glass according to the formation of low-density cristobalite crystals. Therefore, in case of CAS glass, it is necessary to consider the increase of surface roughness and the sintering interference because of foaming bubbles phenomenon at low temperature sintering. Especially, when containing high SiO₂ content, abnormal foaming phenomenon due to crystallization at high temperature should be predicted.

• Journal of Powder Materials
• /
• v.21 no.6
• /
• pp.460-466
• /
• 2014

Al-Si-SiC composite powders with intra-granular SiC particles were prepared by a gas atomization process. The composite powders were mixed with Al-Zn-Mg alloy powders as a function of weight percent. Those mixture powders were compacted with the pressure of 700 MPa and then sintered at the temperature of $565-585^{\circ}C$. T6 heat treatment was conducted to increase their mechanical properties by solid-solution precipitates. Each relative density according to the optimized sintering temperature of those powders were determined as 96% at $580^{\circ}C$ for Al-Zn-Mg powders (composition A), 97.9% at $575^{\circ}C$ for Al-Zn-Mg powders with 5 wt.% of Al-Si-SiC powders (composition B), and 98.2% at $570^{\circ}C$ for Al-Zn-Mg powders with 10 wt.% of Al-Si-SiC powders (composition C), respectively. Each hardness, tensile strength, and wear resistance test of those sintered samples was conducted. As the content of Al-Si-SiC powders increased, both hardness and tensile strength were decreased. However, wear resistance was increased by the increase of Al-Si-SiC powders. From these results, it was confirmed that Al-Si-SiC/Al-Zn-Mg composite could be highly densified by the sintering process, and thus the composite could have high wear resistance and tensile strength when the content of Al-Si-SiC composite powders were optimized.

• Composites Research
• /
• v.30 no.2
• /
• pp.77-83
• /
• 2017

Liquid silicon infiltration, which is one of the methods of producing fiber reinforced ceramic composites, has several advantages such as low fabrication cost and good shape formability. In order to confirm LSI process feasibility of SiC fiber, $SiC_f/SiC$ composites were fabricated using three types of SiC fibers (Tyranno SA, LoxM, Tyranno S) which have different crystallinity and oxygen content. Composites that were fabricated with LSI process were well densified by less than 2% of porosity, but showed an obvious difference in 3-point bending strength according to crystallinity and oxygen content. When composites in LSI process was exposed to a high temperature, crystallization and micro structural changes were occurred in amorphous SiOC phase in SiC fiber. Fiber shrinkage also observed during LSI process that caused from reaction in fiber and between fiber and matrix. These were confirmed with changes of process temperature by SEM, XRD and TEM analysis.

• The Korean Journal of Ceramics
• /
• v.5 no.4
• /
• pp.324-330
• /
• 1999

$Si_3N_4$-$TiB_2$ with 2 wt% $Al_2O_3$ and 4 wt% $Y_2O_3$ additives was hot pressed in a flowing $N_2$ environment with varying $TiB_2$ content from 10 to 50 vol%. Variations of mechanical (hardness, fracture toughness, and flexual strength), and tribological properties as a function of $TiB_2$ content were investigated. As the content of $TiB_2$ increased, relative density decreased due to the chemical reaction of $TiB_2$in $N_2$ environment. The reduction of density causes mechanical properties to be degraded with an increase of $TiB_2$ in $Si_3N_4$. Tribological properties were dependent of microstructure as well as mechanical properties, however, they were degraded strongly by the chemical reaction of $Si_3N_4$-$TiB_2$ during hot pressing in $N_2$ environment. SEM and TEM observations, and X-ray diffraction analysis that the chemical reaction products at the interface are TiCN, Si, and $SiO_2$. Also, the comparison of XRD patterns of the $Si_3N_4$-40 vol% $TiB_2$ composites hot pressed at $1,750^{\circ}C$ for 1 hour between in $N_2$ and in Ar gas was made. The XRD peaks of Si and $SiO_2$ were not found in Ar, but still a weak peak of TiCN was presented.

• Journal of the Korean Ceramic Society
• /
• v.38 no.5
• /
• pp.405-411
• /
• 2001

Compacts of a mixture of fine $\alpha$-Si$_3$N$_4$powders, 6% $Y_2$O$_3$and 1% $Al_2$O$_3$were attrition milled time on phase and microstructural development in silicon nitride ceramics. The sintered surface and the interior showed different behaviors in phase and microstructral developments. Increased oxygen content with increased milling time of powder mixture leads to the formation of Si$_2$$N_2$O phase at temperatures as low as 155$0^{\circ}C$. Si$_2$$N_2$O is stable in the interior of the samples but unstable in the surface region of the specimen sintered at higher temperature. This results in a duplex structure where the interior consists of Si$_2$$N_2$O grains dispersed in $\beta$-Si$_3$N$_4$matrix and a surface which contains only $\beta$-Si$_3$N$_4$. The alpha to beta phase transformation and the microstructural development are shown to be influenced by the formation and decomposition of the Si$_2$$N_2$O.

• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.593-600
• /
• 1992

Through sol-gel processing, Inorganic-organic composite was obtained. The influence of water content used in hydrolysis on the bonding state, microstructure, strength, and elongation into IR, NMR, Tg, etc. As the water content was increased, the bonds between inorganic Si-(OH) and organic Si-(OH) increased, and relatively denser microstructure was formed. Tensile strength and elongation decreased with amount of water content.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1361-1363
• /
• 1997

Zinc oxide-based MOV was fabricated with $SiO_2$ additive ranging from 0.5 to 4.0 mol%, and the microstructure and electrical characteristics were investigated. $Zn_2SiO_4$ phase formed by $SiO_2$ additive was distributed at ZnO grains, grain boundaries, and multiple grain junctions. As the content of $SiO_2$ additive increases, average grain size decreased from 40.6 to $26.9{\mu}m$ due to the Pinning effect by $Zn_2SiO_4$ at grain boundaries Breakdown voltage and nonlinear exponent increased, and leakage current decreased in the range of $11.2{\sim}6.14{\mu}A$ with an increasing $SiO_2$. Donor concentration and interface state density decreased, and barrier height increased in the range of $0.71{\sim}1.04eV$ with an increasing $SiO_2$. While, as the content of $SiO_2$ additive, apparent dielectric constant decreased, peak frequency of dissipation factor decreased in the range of $6.45{\times}10^5{\sim}3.00{\times}10^5Hz$, and dissipation peak was $0.31{\sim}0.22$ at Peak frequency.

• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.88-93
• /
• 2011

This study produced hypereutectic Al-Si clad layer on 1050 Al alloy by a novel laser cladding method. Pure Si powder was mixed with organic binder to make fluid paste which could be screen-printed on the 1050 Al alloy plate. Pulsed Nd:YAG laser was irradiated on the Si paste layer to melt and alloy with Al substrate. Different laser power of 99 W, 179 W and 261 W, was used to see the difference of the microstructure, composition and hardness of the clad layers. When laser power of 179 W was used, the clad layer had overall Si content of 38wt% and composed of fine primary Si particles and fine eutectic phase. At laser power of 261 W, the clad layer had overall Si content of 24wt% and composed of mainly fine eutectic phase. Vickers hardness of HV176.7 and HV150.3 on the clad layer was obtained at laser power of 179 W and 261 W, respectively.

• Journal of the Korean Ceramic Society
• /
• v.44 no.7
• /
• pp.349-353
• /
• 2007

2D SiC fiber-SiC (SiC/SiC) composites were fabricated via slurry infiltration and a stacking process. The effects of the additive composition and content in SiC slurries and the effect of the sintering time on the sintered density and strength of SiC/SiC composites were investigated. A slurry containing $Al_2O_3-Y_2O_3-MgO$ (AYM) additives led to a higher strength compared to a slurry containing $Al_2O_3-Y_2O_3-CaO$ (AYC) additives. The sintered density increased as the sintering time increased and showed a maximum (>98%) at 4 h. In contrast, the flexural strength increased as the sintering time increased and showed a maximum (615 MPa) at 6 h. The relative density and flexural strength increased as the additive content increased.