• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.256-261
• /
• 2007

The purpose of this study is to investigate the effect of shot peening on the fatigue strength and fatigue life of two kinds of aluminum alloys. The fatigue strength behavior of aluminum alloys were estimated by the stress ratio and shot velocities. The fatigue life and strength increased with increasing the test shot velocity. However, at the shot velocity range between 50m/s and 70m/s, the compressive residual stress phenomena were observed in test conditions of different shot velocity. The optimal shot velocity is acquired by considering the peak values of the compressive residual stress, dislocations, brittle striation, slip, and fisheye on the fracture surface of test specimen. It was observed from the SEM observation on the deformed specimen that the brittle striation, fisheye were showed in the intergranular fracture structure boundaries at the this velocities. Therefore, fatigue strength and fatigue life would be considered that shot velocity has close relationship with the compressive residual stress.

• 한국기계기술학회지
• /
• 제20권6호
• /
• pp.844-851
• /
• 2018

In this study, the regression equation was suggested to predict of the shot ball velocity according to blade shapes based on discrete element (DE) analysis. First, the flat type blade DE model was used in the analysis, the validity of the DE model was verified by giving that the velocity of the shot ball almost equal to the theoretical one. Next, the DE analyses for curved and combined blade models was accomplished, and their analytical velocities of shot ball were compared with the theoretical one. The velocity of combined blade model was greatest. From this, the regression equation for velocity of shot ball according to the blade shape based on the DE analysis was derived. Additionally, the wind speed measurement experiment was carried out, and the experimental result and analytical one were the same. Ultimately, it was confirmed that the prediction method of the velocity of shot ball based on DE analysis was effective.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.341-346
• /
• 2002

In this study, an effect that compressive residual stress formed by shot-peening the surface of spring steel(JISG SUP-9) at each shot velocity(1800, 2200, 2600, 3000rpm) on the fatigue crack growth property and threshold stress intensity factor, ${\Delta}K_{th}$, was examined. Followings are the result (1) Compressive residual stress on surface of specimen was determined at each -601 MPa(1800rpm), -638 MPa(2200rpm), -587 MPa (2600rpm), -550 MPa(3000rpm) by shot velocity of shot peening and threshold stress intensity factor, ${\Delta}K_{th}$, fatigue crack growth rate, da/dN, on fatigue crack growth is obstructed by the compressive residual stress was determined at each $5.619\;MPa\sqrt{m}$(Un-peening), $8.319\;MPa\sqrt{m}$(1800rpm), $8.797\;MPa\sqrt{m}$(2200rpm), $7.835\;MPa\sqrt{m}$(2600rpm), $7.352\;MPa\sqrt{m}$(3000rpm) (2) Existing compressive residual stress by effect of shot velocity of shot-peening on relation of crack length. a, and number of cycle, N, was 2 times progressed in case of 2200rpm than specimen of Un-peening on fatigue life. And fatigue life was 1.6 times progressed incase of 3000rpm by Over peening. (3) Fatigue life of Material on Paris' law, $da/dN=C({\Delta}K)^m$, that effect of material constant, C, and fatigue crack growth exponent, m, was influenced by effect of. C and m.

• 한국콘텐츠학회논문지
• /
• 제13권10호
• /
• pp.523-532
• /
• 2013

Fat shot은 골프에서 공보다 뒤땅을 먼저 치게 되는 샷의 공식 용어이다. 본 연구에서는 fat shot과 정상적인 샷의 동작을 비교 분석하였다. K 대학교 교원 5명을 연구대상자로 선정하였으며, 개인별 fat shot이 최소 5개 체크될 때까지, 샷을 계속하게 하였다. AD, MBS, TBS, MDS, IMP, MF를 분석 시점으로 설정하였고, 구간 소요시간, 지면반력 패턴, 백스윙 크기, 팔꿈치 각도, 코킹 각도, 골반과 몸통의 회전, 골반 선속도 각속도 등을 분석하였다. 변인별 차이를 확인하기 위해 대응표본 검증을 실시하였다. Fat shot의 주요 원인으로 간주되는 다운스윙에서의 빠른 코킹 풀림, 다운스윙 초기의 오른 팔꿈치 신전, 뒷발에 체중을 실은 채로 하는 스윙 등의 형태는 나타나지 않았다. 백스윙 크기와 X-Factor 크기, 골반과 몸통의 회전각도, 골반의 회전각속도에서도 두 샷 간 차이가 나지 않았다. 그러나 정상적인 샷에 비해 Fat shot은 다운스윙 초반이 아닌, 후반부 임팩트 바로 직전의 다소 급격한 체중 이동 형태와 다운스윙 과정 중 골반의 타겟 방향으로의 급격한 가 감속, 그리고 골반의 수직 상방으로의 다소 작고 늦은 타이밍의 움직임 속도패턴을 나타내었다.

• 한국운동역학회지
• /
• 제21권5호
• /
• pp.631-638
• /
• 2011

This study had two purposes. The first was to analyze the period of the final record set by the male shot-putters in the IAAF World Championships, Daegu 2011 from the point of view of kinematics. The other was to identify an efficient movement for shot putting based on the analysis. The research used the eight finalists of in the championship as subjects. We analyzed the seven most important kinematic factors in shot putting based on the type of technique: the execution time of the delivery phase, release velocity, release angle, release, center of mass (COM) velocity, and shot trajectories. The analytical results showed the following average figures for the record 12 meters: execution time of the delivery phase: (0.19 s), release height: (2.06 m), release angle: ($34.68^{\circ}$), release velocity: (13.25 m/s), angular velocity of shoulder: ($922.38^{\circ}/s$), and angular velocity of pelvis: ($479.50^{\circ}/s$). Further, the results showed that the highest COM velocity was 2.25 m/s and the shot trajectories were close to a straight line in the release phase.

• 한국운동역학회지
• /
• 제20권1호
• /
• pp.49-55
• /
• 2010

The purpose of the study was to analyze kinetic factors required to the three-point jump shot of the basketball games through 3-D analysis and ground reaction force(GRF) analysis. Six university male players participated in this study. The results of the study were showed that (1) resultant velocity in the center of mass(COM) was $0.84{\pm}0.27\;m/s$ since a player didn't shot a ball in the highest peak and shot ball at the moment of going up forward and vertical movement. Therefore, it is necessary to find a proper timing to shot a ball; (2) the angular velocity was largely increased in upper arm and fore arm out of the upper-limb segments and the hands had the largest angular velocity since the body is in a fixed situation and angular speed is rapidly increased by the wrist' snap with the rapid movement of upper arm and forearm at the time of release a ball; (3) it is judged that a player can shot a ball at the accurate and high release point when the player collects power vertically to the maximum by keeping GRF to the right and the rear in a proper way and by keeping the body's balance so that a large power may not be dispersed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.328-333
• /
• 2003

The purpose of this study is to analyze the impact of shot peening angle on residual stress distribution. From the residual stress analysis of perpendicular shot peening, it could be known that the residual stress in the case of high velocity is larger than low velocity, but the amount of shot size has little effect on the magnitude of compressive residual stress. The centroidal residual stress is not greatly affected by the inclined shot peening but mainly related to the unstable conditions of surface residual stress field. Therefore, this tendency may lead to reduce fatigue life of treated material.

• 한국해양공학회지
• /
• 제17권2호
• /
• pp.47-53
• /
• 2003

The development of new materials with light weight and high strength has become vital to the machinery, aircraft and auto industries. However, there are a lot of problems with developing such materials that require such expensive tools, as well as a great deal of time and effort. Therefore, the improvement of fatigue life through, the adoption of residual stress, is the main focus. The compressive residual stress was imposed on the surface according to each shot velocity(1800, 2200, 2600, 3000rpm) based on Shot-peening, which is the method of improving fatigue life and strength. By using the methose mentioned above, we arrived at the following conclusions; 1. The fatigue crack growth rate(da/dN) of the Shot-peened material was lower than that of the Un-peened material. In stage I, $\Delta$K$_{th}$, the threshold stress intensity factor, of the shot-peen processed material is high in critical parts, unlike the Un-peened material. Also m, fatigue crack growth exponent and number of cycle of the Shot-peened material was higher than of the Un-peened material. That is concluded from effect of da/dN. 2. Fatigue life shows more improvement in the Shot-peened material than in the Un-peened material. Compressive residual stress of the surface on the Shot-peen processed operate resistance force of fatigue crack propagation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권4호
• /
• pp.426-435
• /
• 2005

The lightness of components required in automobile and machinery industries is requiring high strength of components. Therefore this requirement is accomplished as the process of shot-peening method that the compressive residual stress is made on the metal surface as one of various improvement methods. Special research is, therefore, needed about compressive residual stress on the metal surface in the process of shot-peening method. Therefore, in this paper the effect of compressive residual stress of spring steel(JISG SUP-9) by shot-peening on fatigue crack growth characteristics in environmental condition(temperature) and mechanical condition(shot velocity, stress ratio) was investigated with considering fracture mechanics. By using the methods mentioned above, the following conclusions have been drawn. (1) The fatigue crack growth rate(da/dN) of the shot-peened material was lower than that of the un-peened one. In high temperature range. fatigue crack growth rate decreased with increasing temperature range, while fatigue crack growth rate increased by decreasing temperature in low temperature. (2) Fatigue life shows more improvement in the shot-peened material than in the un-peened material. And compressive residual stress of surface on the shot-peen processed operate resistance force of fatigue crack propagation.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.196-202
• /
• 2004

The development of new materials with light weight and high strength has become vital to the machinery, aircraft and auto industries. However, there are a lot of problems with developing such materials that require expensive tools, and a great deal of time and effort. Therefore, the improvement of fatigue strength and fatigue life are mainly focused on adopting residual stress(in this thesis). The compressive residual stress was imposed on the surface according to each shot velocity(57, 70, 83, 96 m/sec) based on Shot-peening, which is the method of improving fatigue life and strength. By using the methods mentioned above, the following conclusions have been drawn. 1. The fatigue crack growth rate(da/dN) of the Shot-peened material was lower than that of the Un-peened material. And in stage I, ΔKth, the threshold stress intensity factor, of the shot-peen processed material is high in critical parts unlike the Un-peened material. Also m, fatigue crack growth exponent and number of cycle of the Shot-peened material was higher than that of the Un-peened material. That is concluded from effect of da/dN. 2. Fatigue life shows more improvement in the Shot-peened material than in the Un-peened material. And compressive residual stress of surface on the Shot-peen processed operate resistance force of fatigue crack propagation.