• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.15-21
• /
• 2002

We investigated effects of electrical, physical, and chemical parameters on energy transfer, NO conversion, and light emission in the dielectric barrier discharge (DBD) process. As gap distance between electrodes increased, discharge onset voltage increased. However, as gap distance between electrodes increased, electric field which initiates discharge showed approximately the same value, 30kV/cm. The discharge onset voltage of the coarse surface electrode was lower than that of the smooth surface electrode. And, energy transfer was slightly enhanced in the coarse electrode condition. However, NO conversion rate decreased with the coarse surface electrode because more uniform discharge can be obtained on the smooth surface electrode. The NO conversion rate increased with decreasing the initial concentration, so the DBD process is more feasible in the lower concentration condition. The variation of gas residence time tested at the same energy density in the experiment did not affect on the NO conversion. The result shows that the NO conversion rate mainly depends on the energy density. The DBD process is able to adjust on plasma-photocatalyst process because it emits the short wavelength light in the range of ultraviolet. The intensity of light emission increased with the increase of the energy transfer to the reactor and the gas flow rate.

• Nuclear Engineering and Technology
• /
• v.33 no.3
• /
• pp.298-306
• /
• 2001

As fuel burnup proceeds, thermal gradients, differential swelling, and inter-assembly loading may induce assembly duct bowing. Since duct bowing affects the reactivity, such as long or short term power-reactivity-decrement variations, handling problem, caused by top end deflection of the bowed assembly duct, and the integrity of the assembly duct itself. Assembly duct bowing were first observed at EBR-ll in 1965, and then several designs of assembly ducts and core restraint system were used to accommodate this problem. In this study, NUBOW-2D KMOD was used to analyze the bowing behavior of the assembly duct under the KALIMER(Korea Advanced Liquid MEtal Reactor) core restraint system conditions. The mechanical behavior of assembly ducts related to several design parameters are evaluated. ACLP(Above Core Load Pad) positions, the gap distance between the ducts, and the gap distance between the duct and restraint ring were selected as the sensitivity parameter for the evaluation of duct deflection.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.1
• /
• pp.50-58
• /
• 2000

The purpose of this study was to investigate the causes of food impaction and to explore solutions as well. For this study, 39 patients with food impaction were selected. 77 contact areas in these patients were investigated mobility, tightness of contact area, gingival index, plaque index, attachment loss, alveolar bone loss, proximal caries, marginal ridge distance and occlusal relationships. The results were as follows ; 1. Teeth without distal support were found to be the most frequent site of food impaction (41.6%). Food impaction was found to be more frequent in the upper teeth (65.2%) than the lower teeth (33.8%). 2. Food impaction was found in tight contact cases (71.4%). Alveolar bone loss was not found in the early stage of food impaction (83.1%) 3. The distance between the marginal ridges of food impaction sites (mean=0.48mm) was short-er than that of the control group. (mean=0.77mm) (p<0.001) 4. In 18.2% of the cases, proximal carries were found at the food impaction site. 5. Food impaction affected patient's occlusion with the following frequencies, cusp to marginal ridge relationship (72.7%), cusp to fossa relationship (3.9%) and stepped relationship (23.4%).

• Journal of the Korean Society for Railway
• /
• v.4 no.3
• /
• pp.102-109
• /
• 2001

In this paper, it has a proposal of the RFID reader antenna design that expand the dedicated short-range communication distance between a static object on the ground and a mobile object attached on the moving article. The static reader equipped with micro-processor makes it possible to have a serial communication with a main system, so that much data can be transfer to the main system. An antenna is adjusted in order to a communication, the scale is designed by results values of simulation using matlab. It is achieved to systematically manage logistics, person resource and security system by grasping the information and location of mobile object on the basis that this system receives the information between a static reader and a mobile object tag at 134.2kHz band on real time, also to make it possible the main system to process. Therefore, the reader antenna scale is controlled on the foundation of a magnetic field theory in order to expand a recognition distance of reader and tag, so that can be optimistically recognized with minimizing the direction influence of reader and tag.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.985-990
• /
• 2004

Leak noise is a good source to identify the exact location of a leak point of underground water pipelines. Water leak generates broadband noise from a leak location and can be propagated to both directions of water pipes. This sound propagation due to leak in water pipelines is not a non-dispersive wave any more because of the surrounding pipes and soil. However, the necessity of long-range detection of this leak location makes to identify low-frequency acoustic waves rather than high frequency ones. Acoustic wave propagation coupled with surrounding boundaries including cast iron pipes is theoretically analyzed and the wave velocity was confirmed with experiment. The leak locations were identified both by the acoustic emission (AE) method and the cross-correlation method. In a short-range distance, both the AE method and cross-correlation method are effective to detect leak position. However, the detection for a long-range distance required a lower frequency range accelerometers only because higher frequency waves were attenuated very quickly with the increase of propagation paths. Two algorithms for the cross-correlation function were suggested, and a long-range detection has been achieved at real underground water pipelines longer than 300m.

• Journal of Korean Institute of Industrial Engineers
• /
• v.33 no.2
• /
• pp.265-272
• /
• 2007

The purpose of Vehicle Routing Problem (VRP) is to design the least costly (distance, time) routes for a fleet of identically capacitated vehicles to serve geographically scattered customers. There may be some restrictions such as the maximal capacity for each vehicle, maximal distance for each vehicle, time window to visit the specific customers, and so forth. This paper is concerned with VRP to minimize the sum of elapsed time from departure, where the elapsed time is defined as the time taken in a moving vehicle from the depot to each customer. It is important to control the time taken from departure in the delivery of perishable products or foods, whose freshness may deteriorate during the delivery time. An integer linear programming formulation is suggested and a heuristic for practical use is constructed. The heuristic is based on the set partitioning problem whose performances are compared with those of ILOG dispatcher. It is shown that the suggested heuristic gave good solutions within a short computation time by computational experiments.

• Explosives and Blasting
• /
• v.25 no.2
• /
• pp.23-33
• /
• 2007

It is difficult to measure a blast noise in the vicinity of tunnel blasting works and the effect of lowering noise changes very highly with types of soundproof materials. So, the main interest of this study focuses on the materials of a soundproof facilities and the method of noise forecast in a near distance. 20 types of the soundproof facilities are established and blast noise is generated using firecracker in a Hume concrete pipe. To analyze the variations of magnitudes of noise and frequency with the soundproof materials and types, the noise and frequency is measured in a short distance next to blast area.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.5
• /
• pp.141-149
• /
• 2006

Ubiquitous computing environment means the computing environment that has taken its position so closely with the ordinary living so much like air or water. In building up the U-Korea, one of the important issues is the social issue from the drasticincrease of senior population. The contemporary society has its distinct trend in increase of senior household following the nuclear family orientation, increase of working parents with the advancement of women in society, unable to support seniors for long distance or short distance of business trip and other reasons that the need of senior welfare has been ever more felt. Accordingly, the Ministry of Government Affairs and Home Administration has developed the wireless paging system to make prompt response system for 119 Rescue when the single senior is encountered with emergency situation that is has been widely provided for the socially neglected people such as single senior, the disabled persons and others. Currently, the wireless paging system is operated as the sub-system for emergency rescue informationsystem, but due to the lack of reliability of product, problems of terminal portable transmitter, receptor and others, rejection of beneficiary and lack of knowledge in use, insufficient management and supervision of managing officers, the efficiency has been declined that there is a need of development for the system. Therefore, this study proposes the context aware information structure of the subject of ubiquitous wireless paging system required forthe development of the wireless paging system model of ubiquitous environment that improved the problems of currently operated wireless paging system.

• Journal of the East Asian Society of Dietary Life
• /
• v.16 no.1
• /
• pp.46-53
• /
• 2006

This study examined the dietary life by residence type of 409 university students (198 male and 211 female) in Chungnam They were divided into five groups according their residence: living in the family home a short distance from the university, living in the family home a long distance from the university, boarding house, self-boarding house, and university dormitory. In this study, the intake of food and nutrients and health, and dietary behaviors of each group were investigated through two-week questionnaire. The average age, height, weight, and BMI were 21.4, 175.3 cm, 68.9 kg, 22.3 in males, and 19.9, 162.3 cm, 53.3 kg, 20.2 in females, respectively. Dietary attitude of the students living in home was higher than that of the other student groups. The rate of breakfast intake and the frequency of eating 10 food items of subjects except processed food of self-boarding house group were lower than those of the other 4 student groups. These results suggest that university students of self-boarding house might have low ability of meal management and more reasonable nutrition education is needed for desirable food behaviors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.733-734
• /
• 2017

Ultrasonic, infrared, and CCD cameras are typically used to obtain location information, but the error range is large depending on the surrounding environment. However, IR-UWB can be used for distance and location measurement both indoors and outdoors, Technology. It is possible to determine the existence and distance of an object by emitting a short signal width in units of 1 ns and using a reflected signal and a time delay. It is also possible to measure the exact position within the cm error irrespective of the environmental conditions. Since it processes a large number of reflection signals, we try to measure three-dimensional spatial coordinates by improving the noise by using the mean value of the signal, the band pass filter and the FFT.