• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1791-1796
• /
• 2011

An optical fiber short period grating of 0.7 nm as a 3 dB wavelength linewidth was fabricated using a Gaussian distributed KrF Eximer laser and a phase mask. This grating has temperature dependancy of 0.01 nm/$^{\circ}C$ over the range of -10 $^{\circ}C$ ~ 70 $^{\circ}C$and no difference between temperature directions. An optical fiber long period grating of 14.22 nm as a 3 dB linewidth was also fabricated using a amplitude mask and has dependancy of 0.01 nm/$^{\circ}C$ over the same range.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.981-982
• /
• 1998

We fabricated sampled fiber grating by double-exposure method. First, a short-period grating was written into the hydrogen-loaded single mode fiber and then the refractive index was modulated over it by an amplitude mask. It was observed that several transmission dips appear due to the index modulation. The thermal and strain responses were measured over $40-180^{\circ}C$ and $0-1800\mu\varepsilon,$ respectively. The dips have the same and linear sensitivity to both physical quantities over the range of measurement.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.11-19
• /
• 2016

By incorporating a polarization-diversity loop configuration, we have demonstrated the inline switching of transmission and reflection spectra of one of two short-period fiber gratings (SPFGs) with different resonance wavelengths without reconfiguring the filter structure. The proposed filtering apparatus consists of a fiber-pigtailed polarization beam splitter, two SPFGs, and three quarter-wave plates (QWPs). The proposed filter can independently choose the transmission or reflection spectrum of each SPFG through the appropriate adjustment of the orientation angles of the QWPs within the filter without additional optical switches and couplers. The average insertion loss, band rejection ratio, and side-mode suppression ratio of the fabricated filter were measured as ~4.59, ~17.88, and ~19.67dB, respectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.232-236
• /
• 1990

Optical waveguide was fabricated in the soda lime glass substrate using rapid thermal method. A chirped grating having period variation of 0.41 - 0.51${\mu}{\textrm}{m}$ on this waveguide for WDM was made. And then, arranging input and output optical fiber, wavelength division multiplexer with 5 channels in short wavelength region was realized. Experiment result of this WDM showed that wavelength spacing, 3 dB bandwidth, insertion loss and crosstalk were 5nm, 4nm, 40dB and less than -10dB, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.17-26
• /
• 2011

Ground anchor method is one of the most popular reinforcing technology in Korea. For the sound monitoring of slope reinforced by permanent anchor for a long period, monitoring the tension force of ground anchor is very important. However, special technology except conventional load cell has not been developed for this purpose. In this paper, a new method is described to replace the conventional strain gauge and V.W. type load cell which has been commonly used as a prestress force monitoring tool for a short-term and long-term. Four 11.5 m long strain detectable tension type anchors were made using FBG sensor embedded tendon since FBG sensor is smaller than strain gauge type load cell and does not have noise from electromagnetic wave. Each two set strain detectable tension type anchors were installed into the different ground conditions, i.e., soft rock and weathered granite soil. Prestress force of ground anchor was monitored during the loading-unloading step from in-situ pullout test using proposed FBG sensor embedded in the tendon and the conventional load cell Test results show that the prestress force monitored from FBG sensor may well be used practically, for it almost matches with that measured from expensive load cell.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.5
• /
• pp.13-25
• /
• 2012

Ground anchor method is one of the most popular reinforcing technology for slope in Korea. For the health monitoring of slope which is reinforced by permanent anchor for a long period, monitoring of the tension force of ground anchor is very important. However, since electromechanical sensors such as strain gauge and V/W type load cell are also subject to long-term risk as well as suffering from noise during long distance transmission and immunity to electromagnetic interference (EMI), optical FBG sensors embedded tendon was developed to measure strain of 7-wire strand by embedding FBG sensor into the center king cable of 7-wire strand. This FBG sensors embedded tendon has been successfully applied to measuring the short-term anchor force. But to adopt this tendon to long-term monitoring, temperature compensation of the FBG sensors embedded tendon should be done. In this paper, we described how to compensate the effect in compliance with the change of underground temperature during long-term tension force monitoring of ground anchors by using optical fiber sensors (FBG: Fiber Bragg Grating). The model test was carried out to determine the temperature sensitivity coefficient (${\beta}^{\prime}$) of FBG sensors embedded tendon. The determined temperature sensitivity coefficient ${\beta}^{\prime}=2.0{\times}10^{-5}/^{\circ}C$ was verified by comparing the ground temperatures predicted from the proposed sensor using ${\beta}^{\prime}$ with ground temperatures measured from ground thermometer. Finally, temperature compensations were carried out based on ${\beta}^{\prime}$ value and ground temperature measurement from KMA for the tension force monitoring results of tension type and compression type anchors, which had been installed more than 1 year before at the test site. Temperature compensated tension forces are compared with those measured from conventional load cell during the same measuring time. Test results show that determined temperature sensitivity coefficient (${\beta}^{\prime}$) of FBG sensors embedded tendon is valid and proposed temperature compensation method is also appropriate from the fact that the temperature compensated tension forces are not dependent on the change of ground temperature and are consistent with the tension forces measured from the conventional load cell.