• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.2
• /
• pp.179-185
• /
• 2014

A use of Asbestos onboard was banned by the provisions of SOLAS since 1 January 2011. And this provision was also implemented by the Rule for Ship's Facilities in Korea. However, these provisions were only declaration and there were no detailed measures for detect, removal and confirmation. In this study, by reviewing the Ship Recycling Convention, IMO circulars and Asbestos Safe Management Act, the following strategies for each concerned parties were proposed. The administration and class society should establish the provisions for appointment of subject vessel which to be inspected for asbestos, criteria for asbestos management and appointment of handling expert. The shipbuilder and equipment manufacturer should make written confirmation that asbestos was not used in their product. And shipowner and ship manager should establish procedure for onboard control of asbestos in the ship's safe management system.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.50-59
• /
• 1997

Shipbuilder checks the status of main engine and propeller operation before sea trial. Generally these tests are carried out at a quay during fitting out of the ship. For these tests the operator has to estimate the maximum RPM with permissible torque and thrust to ensure the safety of the mooring line and ship. In this paper, the propeller characteristics according to the draft variation for a moored ship is inveatigated. From these tests, it is shown that shaft submergence is a dominant parameter in the propeller performance at shallow shaft submergence and that the propeller performance is dependent upon the propeller RPM when the shaft submergence is kept unchanged. In this study, a simple formula of the required thrust for a given propeller shaft submergence and propeller RPM is derived. 1be propeller thrust, which is calculated by another formula in case of dtep draft, is compared with results of bollard pull test for FPSO.

• Journal of Environmental Health Sciences
• /
• v.42 no.2
• /
• pp.85-91
• /
• 2016

Objectives: The objective of this study was to assess heat stress, compare heat stress indices, and evaluate the usefulness of wet bulb globe temperature (WBGT) among outdoor workers exposed to heat during the summer season. Methods: WBGT, dry temperature, and heat index were measured using WBGT measurers (QUESTemp 32 model and QUESTemp 34 model, QUEST, WI, USA) by industrial hygienists from August 27 to September 16, 2015. Heat stress indices were measured at the workplaces of a shipbuilder in Ulsan and a construction site in Daegu. The dry temperature observed by the Automated Synoptic Observing System (ASOS) of the Korea Meteorological Administration was also compared. Results: Dry temperature measured by WBGT is different from that by ASOS. The temperature obtained from ASOS was less than $33^{\circ}C$, above which point a heat wave is forecast by the Korea Meteorological Administration. A heat index above $32.8^{\circ}C$ as a moderate risk was not observed during measurement. WBGT was consistently higher than $22^{\circ}C$, above which the risk of heat-related illness is increased in unacclimated workers involved in work with a high metabolic rate. WBGT was sometimes higher than $28^{\circ}C$, above which the risk of heat-related illness is increased in acclimated workers involved in work with a moderate metabolic rate in September. Conclusion: According to the measurement of heat stress indices, WBGT was more sensitive than heat index and temperature. Thus, general measures to prevent heat-related diseases should be implemented in workplaces during the summer season according to WBGT.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.10 no.3
• /
• pp.133-146
• /
• 2015

This study is to investigate the causal relationship between exchange hedge and the net income of the shipbuilder through the unit root test and co-integration and vector autoregressive model(Vector Autoregressive Model: VAR). First, quarter net income of shipbuilders to order a unit root tests from 2000 to 2013 was used as a value after the Johnson transformation. In the same period, the return on bond futures(KTBF), three years bond yield(KTB3Y), America-Korea exchange differences are weekly data for each quarterly difference in value was converted by utilization, shipbuilding shares after log transformation which it was used. Also, structural change point investigation analysis to verify that looked to take advantage of the structural changes occur in the exchange hedge strategies affecting net income in the shipbuilding industry. Between the exchange hedge and net income of shipbuilders in structural change points detection and analysis showed that structural changes occur starting in 2004. In other words, strategy of shipbuilders about exchange hedge has occurred from "passive exchange hedge" to "active exchange hedge". The exchange hedge of the Korea shipbuilders through the estimation of the VAR was able to grasp that affect the profitability of mutual shipbuilders. Macroeconomic variables and stock prices could also check to see that affected the net income of the shipbuilding industry.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.1
• /
• pp.64-75
• /
• 2009

The shipbuilder's requirement for a higher power output rating has led to the development of a super large two stroke low speed diesel engines. Usually a large-sized bore engine ranging from $8{\sim}14$ cylinders, this engine group is capable of delivering power output of more than 100,000 bhp at maximum continuous rating(mcr). Other positive aspects of this engine type include higher thermal efficiency, reliability, durability and mobility. This plays a vital role in meeting the propulsion requirement of vessels, specifically for large container ships, of which speed is a primary concern to become more competitive. Consequently, this also resulted in the modification of engine parameters and new component designs to meet the consequential higher mean effective pressure and higher maximum combustion pressure. Even though the fundamental excitation mechanisms unchanged, torsional vibration stresses in the propulsion shafting are subsequently perceived to be higher. As such, one important viewpoint in the initial engine design is the resulting vibration characteristic expected to prevail on the propulsion shafting system(PSS). This paper investigated the torsional vibration characteristics of these super large engines. For the two node torsional vibration with a nodal point on the crankshaft, a tuning damper is necessary to reduce the torsional stresses on the crankshaft. Hence, the tuning torsional vibration damper design and compatibility to the shafting system was similarly reviewed and analyzed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1259-1266
• /
• 2022

Recently, due to the specialization of structural design standards and evaluation methods, the classification rules are being integrated. A good example is the common international rules (CSR). However, detailed regulations are presented only for the cargo hold area where the longitudinal load is greatly applied, and no specific evaluation guidelines exist for the bow and stern structures. Structural design of the mentioned area is carried out depending on the design experience of the shipbuilder, and because no clear standard exists even in the classification, determining the root cause is difficult even if a structural damage problem occurs. In this study, an engineering-based solution was presented to identify the root cause of representative cases of buckling damage that occurs mainly in the stern. Buckling may occur at the panel wall owing to hull girder bending moment acting on the stern structure, and the plate thickness must be increased or vertical stiffeners must be added to increase the buckling rigidity. For structural strength verification based on finite element analysis modeling, reasonable solutions for load conditions, boundary conditions, modeling methods, and evaluation criteria were presented. This result is expected to be helpful in examining the structural strength of the stern part of similar carriers in the future.