• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.647-655
• /
• 2021

The IMO (International Maritime Organization) is discussing the improvement of energy ef iciency of ships in order to reduce greenhouse gas emissions from ships. Currently, by applying an ORC power generation system using waste heat generated from ships, high energy conversion efficiency can be expected from ships. This technology uses an organic medium based on Freon or hydrocarbons as the working fluid, which evaporates at a lower temperature range than water. Through this, it is possible to generate steam (gas) and generate power at a low and low temperature relatively. In this study, the analysis of heat flow between the refrigerant and waste heat in the ORC power generation system, which is an organic Rankine cycle, is analyzed using 3D simulation techniques to determine the temperature change, velocity change, pressure change, and mass change of the fluid flowing of the WHRU (Waste Heat Recovery Unit) inside and the outside the structure. The purpose of this study is to analyze how the mass change affects the structure, and this study analyzed the heat transfer of the heat exchanger from the refrigerant and the exhaust gas of the ship's main engine in the ORC power generation system using this technique.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.5
• /
• pp.324-333
• /
• 2013

Recently, rudder erosion due to cavitation has been frequently reported on a semi-spade rudder of a high-speed large ship. This problem raises economic and safety issues when operating ships. The semi-spade rudders have a gap between the horn/pintle and the movable wing part. Due to this gap, a discontinuous surface, cavitation phenomenon arises and results in unresolved problems such as rudder erosion. In this study, we made a rudder model for 2-D experiments using the NACA0020 and also manufactured gap flow blocking devices to insert to the gap of the model. In order to study the gap flow characteristics at various rudder deflection angles($5^{\circ}$, $10^{\circ}$, $35^{\circ}$) and the effect of the gap flow blocking devices, we carried out the velocity measurements using PIV(Particle Image Velocimetry) techniques and cavitation observation using high speed camera in Seoul National University cavitation tunnel. To observe the gap cavitation on a semi-spade rudder, we slowly lowered the inside pressure of the cavitation tunnel until cavitation occurred near the gap and then captured it using high-speed camera with the frame rate of 4300 fps(frame per second). During this procedure, cavitation numbers and the generated location were recorded, and these experimental data were compared with CFD results calculated by commercial code, Fluent. When we use gap flow blocking device to block the gap, it showed a different flow character compared with previous observation without the device. With the device blocking the gap, the flow velocity increases on the suction side, while it decreases on the pressure side. Therefore, we can conclude that the gap flow blocking device results in a high lift-force effect. And we can also observe that the cavitation inception is delayed.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.39 no.3
• /
• pp.1-9
• /
• 2016

NSS (Navigation satellite system) provides the information for determining the position, velocity and time of users in real time using satellite-networking, and is classified into GNSS (Global NSS) and RNSS (Regional NSS). Although GNSS services for global users, the exactitude of provided information is dissatisfied with the degree required in modern systems such as unmanned system, autonomous navigation system for aircraft, ship and others, air-traffic control system. Especially, due to concern about the monopoly status of the countries operating it, some other countries have already considered establishing RNSS. The RNSS services for users within a specific area, however, it not only gives more precise information than those from GNSS, but also can be operated independently from the NSS of other countries. Thus, for Korean RNSS, this paper suggests the methodology to design the satellite constellation considering the regional features of Korean Peninsula. It intends to determine the orbits and the arrangement of navigation satellites for minimizing PDOP (Position dilution of precision). PGA (Parallel Genetic Algorithm) geared to solve this nonlinear optimization problem is proposed and STK (System tool kit) software is used for simulating their space flight. The PGA is composed of several GAs and iterates the process that they search the solution for a problem during the pre-specified generations, and then mutually exchange the superior solutions investigated by each GA. Numerical experiments were performed with increasing from four to seven satellites for Korean RNSS. When the RNSS was established by seven satellites, the time ratio that PDOP was measured to less than 5 (i.e. better than 'Good' level on the meaning of the PDOP value) was found to 94.3% and PDOP was always kept at 10 or less (i.e. better than 'Moderate' level).

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.4
• /
• pp.29-45
• /
• 1991

Lip type stern tube sealing systems have used in almost all the middle or large ships which are being constructed in these days. It seems that the pressure fluctuation of the seal ring interspace, the cross-section profile and the materials quality of the seal rings have great effects on the sealing fuction of this sealing system. In this paper, the mechanical movement of lip seal ring which plays the most important role in stern tube sealing system and the possibility of leakage caused by pressure fluctuation are studied by theory and experiment. Using the finite element method for the axi-symetric object which receives the torsional load, the displacement and stress analysis of the seal rings, and also the possibility of crack occurance is checked by theoretical analysis. If the force which seal ring lip periphery receives is too small, there will be the possibility of leakage caused by the pressure fluctuation of the seal ring interspace, and if this force is too large, the frictional force between the seal ring and the liner will become problematical. The possibility of leakage caused by hardening of seal ring materials and creep phenomena of tested seal rings are also examined. The trial seal rings were designed and manufactured using the program of displacement and stress analysis developed in this study and the experimental apparatus to test the trial seal rings was also designed and manufactured. This trial seal rings were fitted in the experimental apparatus which was made in the same form as an actual stern tube. The one side of this apparatus was filled with sea water and the other side of it was filled with the lubricating oil. The leakage of oil and sea water was checked and the temperature was measured, rotating the propeller shaft at the constant velocity by D.C. motor. It was proved that the trial seal rings made in Viton rubber functioned excellenty but the trial seal rings made in N.B.R. rubber had problem in its durability.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.4
• /
• pp.339-345
• /
• 2008

The stratified flow can be seen in the oil and gas pipelines as well as pipelines related to ship's fluid machineries. Numerous theories and correlations have also been proposed in the past for the prediction of stratified flow in horizontal or slightly inclined pipe. The previous researches are mostly about the effects of physical properties, viscosity, phases densities and pipe geometries on the stratified flow. Very few study outcomes exist on the effect of gravity magnitude and large slop angle of pipe inclinations on the occurring condition of stratified flow. In this study, therefore, analytical procedures were conducted about the effect of both the change in the gravity magnitude and pipe inclinations on the stratified flow occurring conditions. From the analytical results, it was found that stratified flow occurred at the vertical upward inclination and at very low liquid phase flowrates in 0.17g and 0.33g conditions.

• Proceedings of KOSOMES biannual meeting
• /
• 2006.11a
• /
• pp.217-219
• /
• 2006

This study focused an water quality response to land-based pollution loads and the appropriate pollutant load reduction in Chinhae Bay using an eco-hydrodynamic model. Land-based discharge foam urban areas, industrial complex and sewage treatment plant was the greatest contributor to cause red-tide blooms and summer hypoxia. Tidal currents velocity af the ebb tide was about 10 cm/s stronger than that of the flood tide. A residual current was simulated to. have a slightly complicated pattern with ranging from 0.1 to. 2.7 cm/s. In Masan Bay, pollutant materials cannot flaw from the inner to the outer bay easily because af residual currents flaw southward at surface and northward at the bottom. The simulation results of COD distribution showedhigh concentrations aver 3 mg/L in the inner part of Masan Bay related pollutant discharge, and charge, and lower levels less than 1.5mg/L in the central part of Chinhae Bay. For improvement water quality in Chinhae Bay, it is necessary to reduce the organic and inorganic loads from paint sources by mare than 50% and ameliorate severe polluted sediment.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.1
• /
• pp.17-23
• /
• 2020

In this study, the behaviors of a vessel and the ground during the vessel impacting an underwater slope that is part of an artificial protective island are analyzed using the coupled Eulerian-Lagrangian scheme. To consider the large deformation including the shear failure of soil, the Eulerian domain is used to model the ground and water, while the impacting objects are modeled as the Lagrangian domain. For efficiency, the mass scaling scheme is applied to the modeling of the impacting objects, and the ground is modeled by setting the Eulerian volume fraction values. To verify the applicability of the constructed model, a dynamic penetration anchor problem is analyzed. The impacting vessel is modeled using solid elements following the external shape of a container ship, and an analysis of a collision on the slope is performed. As a result, collision behaviors such as displacement, velocity, and dissipation energy are estimated, and the necessity of a parametric study as further research is established.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.2
• /
• pp.1-10
• /
• 2002

Hull-propeller-rudder interactions are studied by the iterative computational procedures. Hull effects on the propeller are reflected through the effective velocities computed by the vortex ring method which used the measured nominal wake as input data. A potential based panel method has been developed to solve the propeller-rudder interactions using the obtained effective velocities. Steady flow characteristics around the rudder surface can be obtained by computing the induced velocities on the rudder by the propeller and vice versa are computed by the iterative manner until the converged solutions are obtained. Flow characteristics around the propeller and the rudder are measured by Laser Doppler Velocimetry(L.D.V.) in large cavitation tunnel at Samsung Heavy industries. The gap flow model is adopted to solve the characteristics of the horn rudder. Numerical results are compared with the experimental values and the computed velocity fields and pressure distributions with rudder angle on the horn rudder surface show good agreement with measured ones in large cavitation tunnel.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.209-217
• /
• 2013

This paper presents an optimal design of a magnetorheological(MR) fluid-based mount(MR mount) that can be used for to vibration control in diesel engines of ships. In this work, a mount that uses mixed-modes(squeeze mode, flow mode, and shear mode) is proposed and designed. To determine the actuating damping force of the MR mount required for efficient vibration control, the excitation force from a diesel engine is analyzed. In this analysis, a model of a V-type engine is considered. The relationship between the velocity and pressure of gas in terms of the torque acting on the piston is derived. Subsequently, by integrating the field-dependent rheological properties of commercially available MR fluid with the excitation force, the appropriate size of the MR mount is designed. In addition, to achieve the maximum actuating force under geometric constraints, design optimization is undertaken using the ANSYS parametric design language software. Through magnetic density analysis, optimal design parameters such as the bottom gap and radius of coil are determined.

• Journal of the Korean Institute of Navigation
• /
• v.13 no.2
• /
• pp.23-36
• /
• 1989

Marine casualities in the high sea are mainly classified into the breakage of hull and capsize , of which the latter occurs frequently to a small craft and container vessels by extreme rolling. The aim of this study is to develop shiphandling techniques for the prevention of ship's large rolling by way of evaluating dangerous degree of rolling in heavy weather. In this study, rolling motion is analized by using statistical method as follow : (1) 8 sample ships is presented for calculation. (2) Analized sea state are Beaufort scale 7 and 10 (wind velocity 30kts and 50kts respectively) and significant wave height is put as 5.2m and 11.2m. (3) The formula recommended by International Towing Tank Conference (ITTC) is used to calculated the wave spectrum. The results of this study are as follow : The results of this study are as follow : (1) Most of the vessels with beam of 20 meters or less was found to be capized in the waves abeam under the sea condition of Bearfort scale7(30kts). (2) For the vessels range 20m to 30m was found safe under the sea conditions of Bearfort scale 7(30kts) and imminent danger under the sea condition of Beaufort scale 11(50kts). (3) It is proved that any vessel could be capsized by heavy rolling regardless of vessel's size whenever the motion is synchronized with waves abeam. This study concludes that the navigator, especially at night , must anticipate the exact wave direction, referring to the wether report and coastaline, not to lay the vessel in the serial wave abeam.