• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.159-169
• /
• 2014

This study generalizes the lateral load-displacement relationship of reinforced concrete shear walls from the section analysis for moment-curvature response to straightforwardly evaluate the flexural capacity and ductility of such members. Moment and curvature at different selected points including the first flexural crack, yielding of tensile reinforcing bar, maximum strength, 80% of the maximum strength at descending branch, and fracture of tensile reinforcing bar are calculated based on the strain compatibility and equilibrium of internal forces. The strain at extreme compressive fiber to determine the curvature at the descending branch is formulated as a function of reduction factor of maximum stress of concrete and volumetric index of lateral reinforcement using the stress-strain model of confined concrete proposed by Razvi and Saatcioglu. The moment prediction models are simply formulated as a function of tensile reinforcement index, vertical reinforcement index, and axial load index from an extensive parametric study. Lateral displacement is calculated by using the moment area method of idealized curvature distribution along the wall height. The generalized lateral load-displacement relationship is in good agreement with test result, even at the descending branch after ultimate strength of shear walls.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.19-24
• /
• 2010

Generally, slope behavior is analyzed by 2-dimensional creep model. Creep behavior shows the deformation variation as time goes by without stress increment. Convention 2-dimensional creep analysis does not have the term of stress variation, it means creep analysis could not figure out the relationship of shear strength variation according to the stress variation and displacement. The slope weight and shear strength is directly related and interlocked to the safety variation and displacement of slope, therefore, this phenomenon could be treated and analyzed as combining the hysteresis and creep, the iteration of this process will result in the slope safety. Furthermore, the combined analysis will be the slope analysis considering shear stress, displacement and shear strength with time variation. In real case, because the variation of shear stress and strength happen at the same time, they should be changed into safety factor which is function of them. This paper shows the 3-dimensional variation of unit weight of soil with hybrid analysis considering creep and hysteresis on the seepage and drainage of rainfall, futhermore variations of shear stress and strength which make the safety factor change.

• Ocean and Polar Research
• /
• v.36 no.4
• /
• pp.495-503
• /
• 2014

This paper focuses on the dynamic responses of a tracked vehicle crawling on extremely cohesive soft soil, each side of which is composed of two parallel tracks. The tracked vehicle consisted of 2 bodies. One body is the tracked vehicle body, which is assumed to be a rigid body with 6 DOFs. The other body is the buoy body. The two bodies are connected by a revolute joint. In order to evaluate the travelling performance of a 7 DOFs vehicle, a dynamic analysis program for the tracked vehicle was developed using Newmark's method and the incremental-iterative method. The effects of road wheels on the track and soil are not taken into account. A terra-mechanics model of extremely cohesive soft soil is implemented in form of relationships: normal pressure to sinkage, shear resistance to shear displacement, and dynamic sinkage to shear displacement. Pressure-sinkage relationship and shear displacement-stress relationship should represent the non-linear characteristics of extremely soft soil. Especially, since the shear resistance of soft soil is very sensitive to shear displacement, spatial distribution of shear displacement occurring at the contact area of the tracks should be calculated precisely. The proposed program is developed in FORTRAN.

• Geomechanics and Engineering
• /
• v.14 no.3
• /
• pp.233-240
• /
• 2018

Pullout tests are usually employed to determine the ultimate bearing capacity of reinforced soil, and the load-displacement curve can be obtained easily. This paper presents an analytical solution for predicting the full-range mechanical behavior of a buried planar reinforcement subjected to pullout based on a bi-linear bond-slip model. The full-range behavior consists of three consecutive stages: elastic stage, elastic-plastic stage and debonding stage. For each stage, closed-form solutions for the load-displacement relationship, the interfacial slip distribution, the interfacial shear stress distribution and the axial stress distribution along the planar reinforcement were derived. The ultimate load and the effective bond length were also obtained. Then the analytical model was calibrated and validated against three pullout experimental tests. The predicted load-displacement curves as well as the internal displacement distribution are in closed agreement with test results. Moreover, a parametric study on the effect of anchorage length, reinforcement axial stiffness, interfacial shear stiffness and interfacial shear strength is also presented, providing insights into the pullout behaviour of planar reinforcements of MSE structures.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.2
• /
• pp.177-187
• /
• 2016

To evaluate the tractive performance of tracked trencher on seafloor surface, a new shear stress-displacement empirical model was proposed for saturated soft-plastic soil (SSP model). To validate the SSP model, a test platform, where track segment shear test can be performed in seafloor soil simulacrum (bentonite water mixture), was built. Series shear tests were carried out. Test results indicate that the SSP model can describe the mechanical behavior of track segment with good approximation in seafloor soil simulacrum. Through analyzing the main external forces applied to seafloor tracked trencher during the uniform linear trenching process, a drawbar pull prediction model was deduced with the SSP model. A tracked walking mechanism of the seafloor tracked trencher prototype was built, and verification tests were carried out. Test results indicate that this prediction model was feasible and effective; moreover, from another side, this conclusion also proved that the SSP model was effective.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.1
• /
• pp.173-180
• /
• 2003

In spite of its potential importance in the assessment of geosynthetic-related dynamic problems, no serious attempt has yet been made to investigate a probable dependence of dynamic friction resistance of the geosynthetic interface on shear displacement rate. Hence, an experimental study of geosynthetics was carried out on a shaking table, and the relationship between dynamic friction resistance and shear displacement rate of geosynthetic interfaces was investigated. A cyclic, displacement rate-controlled experimental setup was used. The subsequent multiple rate tests showed that interfaces that involve geotextiles have such unique shearing characteristics that shear strengths tend to increase with displacement rate. In contrast, once submerged with water, the shear strength appears to be no longer dependent on the displacement rate, partly due to lubrication effect of water trapped inside the interface. The results of the experimental study can be used in the seismic safety assessment of a landfill cover and slope where the geosynthetic materials are exposed to a relatively low normal stress.

• Transactions of Materials Processing
• /
• v.19 no.4
• /
• pp.217-223
• /
• 2010

The objective of this study is to propose the FE model for mechanical clinched joint using cohesive zone model to analyze its failure behavior under impact loading. Cohesive zone model (CZM) is two-parameter failure criteria approach, which could describe the failure behavior of joint using critical stress and fracture toughness. In this study, the relationship between failure behavior of mechanical clinched joint and fracture parameters is investigated by FE analysis with CZM. Using this relationship, the critical stress and fracture toughness for tensile and shear mode are determined by H-type tensile test and lap shear test, which were made of 5052 aluminum alloy. The fracture parameters were applied to the tophat impact test to evaluate the crashworthiness. Compared penetration depth and energy absorption at the point where 50% of total displacement in result of FE analysis and experiment test for impact test, those has shown similar crashworthiness.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.4
• /
• pp.53-59
• /
• 2022

In this study, an enhanced first-order shear deformation theory is proposed to efficiently and accurately predict the thermo-mechanical-viscoelastic coupled behavior of laminated composite structures. To this end, transverse shearstress and displacement fields are independently assumed, and the strain-energy relationship between these fields issystematically established using the mixed variational theorem (MVT). In MVT, the transverse shear stress fields are obtained from the third-order zigzag model, whereas the displacement fields of the conventional first-order model are considered to amplify the benefits of numerical efficiency. Additionally, a transverse displacement field with a smooth parabolic distribution is introduced to accurately predict the thermal behavior of composite structures. Furthermore, the concept of Laplace transformation is newly employed to simplify the viscoelastic problem, similar to the linear-elastic problem. To demonstrate the performance of the proposed theory, the numerical results obtained herein were compared with those available in the literature.

• Structural Engineering and Mechanics
• /
• v.73 no.2
• /
• pp.123-132
• /
• 2020

Steel spherical hinged bearings have high loading capacity, reliable load transfer, flexible rotation with universal hinge and allowance of large displacement and rotation angle. However, bearings are in complex forced states subject to various load combinations, which lead to the significant influence on integral structural safety. Taking the large-tonnage complex steel spherical hinged bearings of Terminal 2 of Guangzhou Baiyun International Airport as an example, full-scale rotation and shear behaviour tests of the bearings subject to axial tensile load are carried out, and the corresponding finite element simulation analyses are conducted. The results of experiments and finite element simulations are in good agreement with the coincident development tendency of stress and deformation. In addition, the measured rotational moment is less than the calculated moment prescriptive by the code, and the relationship between horizontal displacement and horizontal shear force is linear. Finally, based on these results, the rotation and shear stiffness models of bearings subject to axial tensile load are proposed for the refinement analysis of integral structure.

• Computers and Concrete
• /
• v.13 no.2
• /
• pp.221-234
• /
• 2014

A nonlinear finite element analysis using ANSYS is used to evaluate the seismic behavior of reinforced concrete exterior beam-column joints. The behavior of the finite element models under cyclic loading is compared with the experimental results. Two beam-column joint specimens (SH and SHD) with square hoop confinement in joint and throughout the column with detailing as per IS 13920 are studied. The specimen SHD was provided with additional diagonal bars from column to beam to relocate the plastic hinge formation from beam-column interface. The load-displacement relationship, joint shear stress and strain in beam obtained from numerical study showed good agreement with the experimental results. This investigation proves that seismic behaviour of reinforced concrete beam-column joints under reversed cyclic loading can be evaluated successfully using finite element modeling and analysis.