• 한국지반공학회논문집
• /
• 제18권3호
• /
• pp.126-126
• /
• 2002

지진에 의한 지반거동 및 지반-구조물 상호작용 등 지반동역학적 문제분석을 위해서는 정확한 동적 토질전단탄성계수의 획득이 필수적이다. 본 연구에서는 기존의 자료를 조사분석하여 어떤 변형율에서도 활용할 수 있는 사질토 전단탄성계수 감소곡선을 위한 경험식을 제안하였다. 비소성 토질의 전단탄성계수 감소곡선의 위치와 모양은 평균유효구속압에 주로 영향을 받으므로 본 연구에서는 이 영향요소 및 최대전단탄성계수를 이용하여 변형을 증가에 의한 전단탄성계수 감소를 산정할 수 있는 방정식을 형성하였다. 최대전단탄성계수가 측정되면 제안된 식을 이용하여 특정 변형을 및 구속압에서 감소된 전단탄성계수를 산출할 수 있을 것이다.

• 한국지반공학회논문집
• /
• 제18권3호
• /
• pp.127-138
• /
• 2002

지진에 의한 지반거동 및 지반-구조물 상호작용 등 지반동역학적 문제분석을 위해서는 정확한 동적 토질전단탄성계수의 획득이 필수적이다. 본 연구에서는 기존의 자료를 조사분석하여 어떤 변형율에서도 활용할 수 있는 사질토 전단탄성계수 감소곡선을 위한 경험식을 제안하였다. 비소성 토질의 전단탄성계수 감소곡선의 위치와 모양은 평균유효구속압에 주로 영향을 받으므로 본 연구에서는 이 영향요소 및 최대전단탄성계수를 이용하여 변형을 증가에 의한 전단탄성계수 감소를 산정할 수 있는 방정식을 형성하였다. 최대전단탄성계수가 측정되면 제안된 식을 이용하여 특정 변형을 및 구속압에서 감소된 전단탄성계수를 산출할 수 있을 것이다.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.519-533
• /
• 2024

Many materials including cementitious concrete-type materials undergo material property changes during high-rate loading. There is a wealth of research regarding this phenomenon for concrete in compression and tension. However, there is minimal knowledge about how mortar material used in concrete masonry unit (CMU) construction behaves in high-rate shear loading. A series of experiments was conducted to examine the bond strength of mortar bonded to CMU units under high-rate shear loading. A novel experimental setup using a shock tube and dynamic ram were used to load specially constructed shear triplets in a double lap shear configuration with no pre-compression. The Finite Element Method was leveraged in conjunction with data from the experimental investigation to establish if the shear bond between concrete masonry units and mortar exhibits any rate dependency. An increase in shear bond strength was observed when loaded at a high strain rate. This data indicates that the CMU-mortar bond exhibits a rate dependent strength change and illustrates the need for further study of the CMU-mortar interface characteristics at high strain rates.

• Steel and Composite Structures
• /
• 제21권6호
• /
• pp.1265-1285
• /
• 2016

This paper presents experimental results of advanced investigation carried out on the beams reinforced with Glass Fiber Reinforced Polymer (GFRP) rebar and stirrups. Twelve beams reinforced with GFRP and one beam with steel reinforcement of size $230{\times}300{\times}2000mm$ were investigated. Longitudinal reinforcement, shear span and spacing of stirrups were the main variables to form the set. In advanced testing three types of strain gauges for steel, composite and concrete surface were applied to observe strain/stress development against the applied load. Live data were recorded from four strain gauges applied on stirrups, one at center on longitudinal reinforcement, two on the concrete surface and central deflection during the test. Although the focus of the paper was mainly on the behavior of GFRP shear reinforcement, other parallel data were observed for the completeness of the test. Design recommendations of ISIS Canada Design Manual (2007), Japan Society of Civil Engineers (1997) and American Concrete Institute (ACI-440.1R-06) were reviewed. Shear design predictions were compared with experimental results in which it was observed that all the three standards provided conservative predictions. However, ACI found most efficient compare to other two there is room to improve the efficiency of the recommendations.

• 한국해양공학회지
• /
• 제30권6호
• /
• pp.468-473
• /
• 2016

This paper focuses on the estimation of local ice loads exerted from ship-ice interaction processes. The Korean IBRV ARAON was used to perform field ice trials during her 2015 Arctic voyage. During ARAON's general ice transit, a total of 72 channels of data from both strain gauges on the inner hull plates and those installed on the transverse frames of the ARAON's bow section structures were analyzed to calculate the local ice loads. The local ice loads estimated from the analysis of the shear strain data measured on the side frames were compared to those from the hull plate pressures.

• Journal of Pharmaceutical Investigation
• /
• 제39권3호
• /
• pp.185-199
• /
• 2009

Using a strain-controlled rheometer [Advanced Rheometric Expansion System (ARES)], the steady shear flow properties and the dynamic viscoelastic properties of $Antiphlamine-S^{(R)}$ lotion have been measured at $20^{\circ}C$ (storage temperature) and $37^{\circ}C$ (body temperature). In this article, the temperature dependence of the linear viscoelastic behavior was firstly reported from the experimental data obtained from a temperature-sweep test. The steady shear flow behavior was secondly reported and then the effect of shear rate on this behavior was discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters. The angular frequency dependence of the linear viscoelastic behavior was nextly explained and quantitatively predicted using a fractional derivative model. Finally, the strain amplitude dependence of the dynamic viscoelastic behavior was discussed in full to elucidate a nonlinear rheological behavior in large amplitude oscillatory shear flow fields. Main findings obtained from this study can be summarized as follows : (1) The linear viscoelastic behavior is almostly independent of temperature over a temperature range of $15{\sim}40^{circ}C$. (2) The steady shear viscosity is sharply decreased as an increase in shear rate, demonstrating a pronounced Non-Newtonian shear-thinning flow behavior. (3) The shear stress tends to approach a limiting constant value as a decrease in shear rate, exhibiting an existence of a yield stress. (4) The Herschel-Bulkley, Mizrahi-Berk and Heinz-Casson models are all applicable and have an equivalent validity to quantitatively describe the steady shear flow behavior of $Antiphlamine-S^{(R)}$ lotion whereas both the Bingham and Casson models do not give a good applicability. (5) In small amplitude oscillatory shear flow fields, the storage modulus is always greater than the loss modulus over an entire range of angular frequencies tested and both moduli show a slight dependence on angular frequency. This means that the linear viscoelastic behavior of $Antiphlamine-S^{(R)}$ lotion is dominated by an elastic nature rather than a viscous feature and that a gel-like structure is present in this system. (6) In large amplitude oscillatory shear flow fields, the storage modulus shows a nonlinear strain-thinning behavior at strain amplitude range larger than 10 % while the loss modulus exhibits a weak strain-overshoot behavior up to a strain amplitude of 50 % beyond which followed by a decrease in loss modulus with an increase in strain amplitude. (7) At sufficiently large strain amplitude range (${\gamma}_0$>100 %), the loss modulus is found to be greater than the storage modulus, indicating that a viscous property becomes superior to an elastic character in large shear deformations.

• 콘크리트학회논문집
• /
• 제12권4호
• /
• pp.23-30
• /
• 2000

The purpose of this paper is to study on the shear strength of high strength concrete beams with steel fibrous. In general, the shear strength of reinforced concrete beams is affected by the compressive strengths of concrete( c), the shear span-depth ratio(a/d), the longitudinal steel ratio($\rho$ $\omega$), and shear reinforcement. An experimental investigation of the shear strength of high strength concrete beams with steel fibrous was conducted. In each series the shear span-depth ratio(a/d) was held constant at 1.5, 2.8, or 3.6, while concrete strengths were varied from 320 to 520, to 800kgf/$\textrm{cm}^2$. To verify the proposed equations the experimental results were compared with those from other researches such as equation of ACI code 318-95 or equation of Zsutty. To deduce equation for shear strength from experimental data carried out MINITAP program. According to the experimental results, the addition of steel fibrous has increased the deflection and strain at failure load, improving the brittleness of the high strength concrete.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권3호
• /
• pp.421-425
• /
• 2018

The icebreaking research vessel ARAON performed ice field tests during her 2016 Arctic voyage. The ship is subjected to ice loads through ice-ship interaction processes. Local ice load acting on ARAON's bow section was measured by using stain gauges installed on the inner hull plates and transverse frames of bow section. In this paper the local ice loads at transverse frames estimated from shear strain data were compared to ice loads from hull plate pressures by using the influence coefficient method. In addition to the analysis of local ice loads, the characteristics of peak ice loads with the ship speed is also discussed. It is recommended that the local ice loads estimated by calculating shear forces acting on transverse frames may be useful in estimating local ice loads on the hull of ship.

• 한국지반신소재학회논문집
• /
• 제2권1호
• /
• pp.57-68
• /
• 2003

Strain-softening model is developed to characterize the interface behavior of geomembrane with geotextile and geosynthetic clay liner(GCL). The model proposed in this research is calibrated by using data from direct shear tests conducted on smooth and textured geomembrane. The research is divided into two regions, pre-peak and post-peak, to take into account of strain-softening effect. Although slight difference between measured and back calculated data is observed under high normal stress, good agreements, in general, are found from back calculations. Especially, good consistency is observed in the case of low normal stress. Based on the results, it can be concluded that the proposed model can be a reasonable constitutive law to figure out the behavior of strain-softening between interfaces of geomembrane. In addition, DSC(Disturbed State Concept) model is also presented for further application in geosynthetic interfaces.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1521-1528
• /
• 2011

자동차용 고무부품에 대한 유한요소 해석의 신뢰 향상을 위하여 고무소재 물성치에 대한 연구를 수행하였다. 마운트 설계를 위하여 수백 종의 고무 물성치를 모두 측정하는 것은 현실적으로 어렵다. 그래서 시험 값을 대신하는 순수전단 시험 데이타의 변환 방법을 제시하여 유효성을 확인하였다. 순수전단시험의 응력-변형 관계의 변환은 단순인장시험 데이터와 주 연신률의 함수로 정의한 푸아송의 비를 사용하였다. 카본 충진 고무의 변환 순수전단시험 데이터는 100%변형까지 시험 데이터와 상당히 유사하다. 단순인장시험 데이타와 함께, 순수전단시험의 변환 데이타와 시험 데이터를 각각 사용한 허브베어링 씰의 접촉력에 대한 유한요소해석 결과들은 시험 데이터와 거의 일치하였다. 해석에 사용된 재료상수는 Ogden 상수이다.