• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.71-76
• /
• 2001

This paper describes a research work of developing system for conceptual die design system for Fine blanking. The method of approaching to the system is based on the knowledge-based rules. Knowledge for the system is formulated from experimental results and the empirical knowledge of field experts. This system has been written in VisualLISP on the AutoCAD using a personal computer and in Microsoft Visual Basic ver.6.0. Transference of data is accomplished by DXF (Drawing Exchange Format) method. This system consists of six modules, which are cognition of a drawing, cognition of shear length, calculation of shear force, materials properties database, determination of degree of difficulty of the product, determination of approximate life of punch and die modules. Results carried out in each module will provide efficiency to the designer and the manufacturer of die for Fine blanking. But the main focus of this system is the design of die for Fine blanking in the level of general concept. In order to use powerful tool in this field, developed system will be studied continuously.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.74-80
• /
• 2014

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from their devices and system. Especially, reliability issue of lead-free solder joint is increasing in car electronics due to ELV (End-of-Life Vehicle) banning from 2016. We have prepared engine control unit (ECU) modules soldered with Sn-40Pb and Sn-3.0Ag-0.5Cu (SAC305) solders, respectively. Degradation characteristics of solder joint strength were compared with various conditions of automobile environment such as cabin and engine room. Thermal cycle test (TC, $-40^{\circ}C$ ~ ($85^{\circ}C$ and $125^{\circ}C$), 1500 cycles) were conducted with automotive company standard. To compare shear strength degradation rate with eutectic and Pb-free solder alloy, we measured shear strength of chip components and its size from cabin and engine ECU modules. Based on the TC test results, finally, we have known the difference of degradation level with solder alloys and use environmental conditions. Solder joints degradation rate of engine room ECU is superior to cabin ECU due to large CTE (coefficient of thermal expansion) mismatch in field condition. Degradation rate of engine room ECU is 50~60% larger than cabin room electronics.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.391-398
• /
• 1999

Dynamic properties of hydraulic mechanically stabilized slag(HMS25) was studied for utilizing it as a roadbed material. HMS25 is a by product material during pig iron production process. It has a very good potential application as a roadbed material. Therefore, the resonant column and torsional shear tests were carried out to evaluate the dynamic properties of HMS25 which are necessary for designing roadbed of railroad track. As a result, it was found that HMS25 has excellent dynamic properties required for roadbed material used in railroad track.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.3
• /
• pp.185-192
• /
• 2003

This study consolidation undrain Triaxial Compression Tests using constant confining pressure in clay that receive preconsolidation stress that is different and, void ratio, pore water pressure coefficient, shear strength compare with another thing theory and studied analyzing change relation of elastic modules. The summary of analysis is follows: If preconsolidation stress increases in same confining stress in relation of preconsolidation stress and deviator stress, deviator stress is proportional and increased. Can know that excess void pressure is proportional and decreases in size of preconsolidation stress in same confining stress state if preconsolidation stress increases preconsolidation stress and relation of excess void pressure. Also, over consolidated state can assume that this is thing by Dilatancy's effect though excess void pressure decreased remarkably. Preconsolidation stress and relation of stress path can know that shear strength degree increases preconsolidation stress increases, and specially, preconsolidation stress was appear in stress path form of overconsolidated state case of clay that receive at 300, 400, 500kPa in 100, 150kPa's deviator stress.

• Steel and Composite Structures
• /
• v.37 no.6
• /
• pp.733-740
• /
• 2020

The subject of the paper pertains to simply supported beams with bisymmetrical cross sections under three-point bending with consideration of the shear effect. The deformation of a planar cross section of the beam is described taking into account the assumed nonlinear hypothesis-theory. Two differential equations of equilibrium are obtained based on the principle of stationary potential energy. This system is analytically solved and the shear coefficients and deflections of the beams are derived. Moreover, the Young's modules of the materials and deflections of the beams are experimentally determined on a test stand. The results of the studies are specified in tables and compared.

• International Journal of Concrete Structures and Materials
• /
• v.10 no.3
• /
• pp.297-306
• /
• 2016

This paper developed an analytical software, called Simulation of Concrete Structures (SCS), which is used for numerical analysis of shear-critical prestressed steel fiber concrete structures. Based on the previous research at the University of Houston (UH), SCS has been derived from an object-oriented software framework called Open System for Earthquake Engineering Simulation (OpenSees). OpenSees was originally developed at the University of California, Berkeley. New module has been created for steel fiber concrete under prestress based on the constitutive relationships of this material developed at UH. This new material module has been integrated with the existing material modules in OpenSees. SCS thus developed has been used for predicting the behavior of the prestressed steel fiber concrete I-beams and Box-beams tested earlier in this research. The analysis could well predict the entire behavior of the beams including the elastic stiffness, yield point, post-yield stiffness, and maximum load for both web shear and flexure shear failure modes.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.126-133
• /
• 2017

This paper presents the shear capacities of hollow slab with plate and octagonal pillar type hollow sphere. Recently, the interest in precast hollow slab system for buildings is growing up according to the demand for high quality control and the increase in slab thickness. A hollow slab system is widely known as one of the effective slab system which can reduce self-weight of slab. However, hollow slabs are vulnerable to the deterioration in the shear strength due to the decrease of concrete at slab web which resists shear. Especially, in case of precast hollow slabs, it has joint surface between precast concrete slab modules along transverse axis of slab, and shear failure, that is caused by cracks at joints, has to be prevented. Therefore, in this study, shear capacity of the I-slab system is evaluated by 3-points-supported shear test along the longitudinal and transverse axis of slab specimen. Test results showed that I-slab had enough shear strength compared to theoretical shear strength even if it included the joint surfaces.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.571-578
• /
• 2022

Modularization in a high-rise building is different from a small building, as it is exposed to more lateral forces like wind and earthquakes. The integrity, robustness, and overall stability of the modules and their performance is based on the joining techniques and strong structural systems. High lateral stiff construction structures like concrete shear walls and frames, braced steel frames, and steel moment frames are used for the stability of high-rise modular buildings. Similarly, high-rise stick-built buildings have concrete cores and perimeter frames for lateral load strength and stiffness. Methods for general steel-concrete connections are available in many works of literature. However, there are few modular-related papers describing this connection system in modular buildings. This paper aims to review the various research and practice adopted for steel-to-concrete connections in construction and compare the methods between stick-built buildings and modular buildings. The literature review shows that the practice of steel module-to-concrete core connection in high-rise modular buildings is like outrigger beams-to-concrete core connection in stick-built framed buildings. This paper concludes that further studies are needed in developing proper guidelines for a steel module-to-concrete core connection system in high-rise modular buildings.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.61-68
• /
• 2023

In this study, Sn-3.5Ag-15.0Fe composite solder was manufactured and applied to TLP bonding to change the entire joint into a Sn-Fe IMC(intermetallic compound), thereby applying it as a high-temperature solder. The FeSn₂ IMC formed during the bonding process has a high melting point of 513℃, so it can be stably applied to power modules for power semiconductors where the temperature rises up to 280℃ during use. As a result of applying ENIG surface treatment to both the chip and substrate, a multi-layer IMC structure of Ni₃Sn₄/FeSn₂/Ni₃Sn₄ was formed at the joint. During the shear test, the fracture path showed that cracks developed at the Ni₃Sn₄/FeSn₂ interface and then propagated into FeSn₂. After 2hours of the TLP joining process, a shear strength of over 30 MPa was obtained, and in particular, there was no decrease in strength at all even in a shear test at 200℃. The results of this study can be expected to lead to materials and processes that can be applied to power modules for electric vehicles, which are being actively researched recently.

• Membrane Journal
• /
• v.25 no.3
• /
• pp.268-275
• /
• 2015

Effects of aeration intensity on local fouling were investigated in submerged membrane modules. Higher liquid velocities were observed at the section with the lower fiber packing density. The liquid velocity is increased with increasing the gas-liquid injection factor. The high shear stress coincided with the high liquid velocity. The shear stress increases with the increasing of gas-liquid injection factor and the liquid velocity improves with the increasing of gas-liquid injection factor. Irreversible fouling resistance ($R_{ir}$) of the fiber position is significant in a local region of high suction pressure near the suction point of the fiber (position 1). The ratio of $R_{ir}/R_m$ and $R_{ir}/R_r$ of position 1 was highest compared to the position 2 and 3. Irreversible fouling resistances results confirmed the preferential deposition of foulants near the suction part of the fiber where the local suction pressure is the highest and correspondingly, more particles are accumulated to the membrane surface. The effects of local fouling along the fiber length are significant factors to optimize the design of submerged modules.