• 지구물리와물리탐사
• /
• 제23권1호
• /
• pp.1-12
• /
• 2020

섭입 및 열개와 같이 대변형을 수반하는 지구동역학적 현상 발생은 암석권의 국지적인 약대의 발달이 필요하다. 이러한 약화 기작 중 하나인 전단열은 암석권의 온도를 국부적으로 높여 강도를 낮추는 역할을 하여 암석권 파괴를 촉진시킬 수 있다. 본 연구에서는 전단열에 대한 정량적인 분석을 위하여 2차원 탄소성 인장 분지 모형을 제작하여 기존 수치 모사 연구를 벤치마크하였다. 암석권의 항복강도, 인장 속도, 변형량- 및 온도-의존성 약화 현상 등을 조절하여 전단열 발생량에 미치는 영향을 분석하였다. 실험 결과, 약화를 고려하지 않은 경우 전단열의 발생량은 암석권의 항복강도 및 인장 속도와 양의 상관관계가 있는 것으로 나타났다. 기준 모형인 항복강도 100 MPa, 인장 속도 2 cm/yr로 설정된 경우, 총 20 km 인장된 시점(0.025의 변형률)에서 ~ 50 K의 온도 상승을 보여주었다. 소성 변형 및 온도에 따른 약화가 포함된 경우에는, 더 효율적인 약화 기작이 더 강한 전단열의 생성으로 이어지는데 이러한 현상은 약화 기작과 전단열 발생 사이에 양성되먹임이 작용함을 지시한다. 또한 변형 초기에 급격한 전단열 발생량을 보여주지만, 변형이 지속되어 암석권의 강도가 약화되면 전단열 발생 속도가 최대 ~ 80% 감소했다. 이는 약화 기작이 포함된 경우 전단열은 비교적 손상되지 않은 상태인 암석권의 강도에 큰 영향을 미침을 시사한다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.86-88
• /
• 2003

The characteristic of induction heating solder bump(solder ball: Sn-37Pb, Sn-3.5Ag, Sn-3.0Ag-0.5Cu) has analyzed in this paper. The initial condition of induction heating depends on the time and current. The shape of lead-free solder bump is better than lead solder. The shear strength of lead solder bump has decreased with aging time. The average of shear strength of solder bump is about 10N, 11N, and 11N respectively. The lead-free solder bump's shear strength is better than lead solder and varies irregularly with aging time.

• 한국식품영양학회지
• /
• 제32권4호
• /
• pp.304-311
• /
• 2019

Ohmic heating is a heating method based on the principle when an electrical current passes through food. Since this method is internal, electrical current damage occurred during heating treatment. The results of ohmic heated starch's external structure, X-ray diffraction, DSC analysis and RVA were differed from those of conventional heating at the same temperature. Several starches changed more rigid by structure re-aggregation. This change in starch was caused by change of physical, chemical, rheological property. The rheology of ohmic heated potato and corn starch of different heated methods were compared with chemically modified starch. After gelatinization, sample starch suspension (2%, 3%) measured flow curves by rheometer. Cross-linked chemically modified starch's shear stress was decreased with degree of substitution reversibly. Ohmic heated more dramatic, at $60^{\circ}C$. Potato starch's shear stress was less than commercial high cross-linked modified starch. Flow curves of potato starches measured at $4^{\circ}C$, $10^{\circ}C$, $20^{\circ}C$. Showed that Ohmic heated potato starch's shear stress ranging between $4^{\circ}C$ and $20^{\circ}C$ was narrower than modified starch. According to this study, ohmic heated potato starch can be used by decreasing viscosity agent like cross-linked modified starch.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• 한국지진공학회논문집
• /
• 제20권5호
• /
• pp.311-318
• /
• 2016

The lead-rubber bearing (LRB) dissipates seismic energy through plastic deformation of lead core. Under large-displacement cyclic motion, the temperature increases in the lead core. The shear strength of a lead-rubber bearing is reduced due to the heating effect of the lead core. In this study, the seismic responses such as displacement increasing, shear strength and vertical stiffness degradations of LRB due to the heating effect are evaluated for design basis earthquake (DBE) and beyond design basis earthquake (150% DBE, 167% DBE, 200% DBE).

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.181-183
• /
• 2006

This paper studies the mechanical behaviors of Sn-3.5Ag solder joint against substrate(such as Au/Ni/Cu, Au/cu, Ni/Cu and Cu pad) after induction heating, a new soldering method. It was found that the solder bump formation depends on the time and current of the induction heating system. Also the heating value of the solder bump were found to vary with respect to the thermal conductivity of the pads on the substrate. In case of Au/Ni/Cu pad and Au/Cu pad, solder bump's shear strength were high for the heating time of $1.5{\sim}2sec$. For Ni/Cu pad, solder bump's shear strength were found to increase with time increment.

• 한국건축시공학회지
• /
• 제12권5호
• /
• pp.539-547
• /
• 2012

To manufacture laminated wood with improved mechanical properties by providing uniform adhesiveness, the adhesive was applied and the plate adhesive was laminated on the wood surface. Then, after laminating the wood on the top part of the adhesivebond, it was heated and dried while the adhesive was stiffened using microwaves, and the test piece was manufactured by compressing it with the press machine for thirty minutes. The temperature and the water content were examined according to the heating time of the wood heated with the microwave, and testing was conducted on the shear strength and flexural strength of the wood. In addition, the microstructure of the adhesive bond between the wood was recorded to confirm the penetrabilityinto the wood structure for the adhesive. After the test was conducted, it was found that the test piece manufactured with wood that has its water content leveled with the microwave heating showed improved shear strength and bending strength compared to the standard test piece. With regard to adhesives, liquefied polyvinyl acetate resin and plate's PVB resin were found to have superior adhesive strength. Also, after filming the cellular microstructure, it was found that when the laminated wood is heated with microwaves, the infiltration of the adhesive into the inside of the wood becomes easy, which makes it effective for improving adhesiveness.

• 대한기계학회논문집A
• /
• 제40권3호
• /
• pp.245-252
• /
• 2016

본 논문은 벤드(bend)부의 노후 문제를 경감시키기 위한 대안으로 폼패드를 없앤 이중보온관의 형상 설계를 제안하였다. 전 관경에 대해 유한요소해석을 수행하였으며, 이를 토대로 전단제어링 형상을 결정하였다. 제안된 전단제어링 사양 강화이형관에 대한 현장 시공 시험은 진행하였으며, 온도와 응력 데이터를 취득 및 분석하였다. 강화이형관의 제작과 현장 시범시공을 통하여 강화이형관이 폼패드를 시공하지 않으면서도 강관의 열응력이 허용치 기준내에 있음을 확인하였다. 특히 보온재의 전단강도가 강화되어 폼패드를 적용한 기존 벤드보다 낮은 최대 전단응력이 발생함을 확인함으로써, 강화이형관 적용에 따른 구조 안전성 향상 효과를 확인하였다.

• 한국전산유체공학회지
• /
• 제9권3호
• /
• pp.18-25
• /
• 2004

Multi plume effects on the base heating have been Investigated with a CFD program. As the flight altitude increases, the plume expansion angle increases regardless of the single or clustered engine. The plume interaction of the clustered engine makes a high temperature thermal shear in the center of four plumes. At low altitude, the high temperature shear flow stays in the center of plumes, but it increases up to engine base with the increasing altitude. At high altitude, the flow from plume to base and the flow from base into outer free stream are supersonic, which transfers the high heat in the center of plumes to the base region. The radiative heat of the clustered engine varies from 220 kW/m² to 469 kW/m² with increasing altitude while those of the single engine are 10 kW/m² and 43.7 kW/m². And the base temperature of the clustered engine varies from 985K to 1223K, and those of the single engine are 483K and 726K. This big radiative heat of clustered engine can be explained by the active high temperature base flow and strong plume interactions.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2008년도 춘계학술논문발표회 논문집
• /
• pp.48-51
• /
• 2008

Shear connector is the element which resist in the horizontal shear force between steel and concrete of composite members and the stud bolt is often used because of its constructional convenience and serviceability. Although the push-out test is the most common method to evaluate shear slip behaviour, it is suitable for only room temperature conditions. In this study, we investigated about shear force, temperature distribution and slip displacement of shear connector in high temperature through the modified push-out test with electronic furnace invented for steel part heating.