• 한국의류산업학회지
• /
• 제1권3호
• /
• pp.288-295
• /
• 1999

This study was conducted to examine the fatigue phenomenon of mechanical properties in tencel fabrics by repeated washing & shear and tensile deformation. The obtained results are as follows. After performing repeated shear tensile deformation, RT of tencel showed higher increase rate than that of cotton and rayon, whereas its WT and EM was a smaller decrease rate than that of them. This means that tencel's resistance to tensile deformation was the greatest. In the repeated washing and shear tensile deformation, tencel's 2HB, 2HG and 2HG5 showed a remarkable increase rate. In terms of deformation frequency, the greatest change rate appeared at the time of 1000 cycles of repeated shear tensile deformation and 15 times of repeated washing. In the hand value and THV, KOSHI showed a higher increase rate for tencel than for cotton and rayon in both repeated washing and shear tensile deformation, and NUMERI showed a higher increase rate. In the THV the change rate of rayon and cotton could be rarely seen but for tencel, it decreased. tencel's change rate of thermal insulation value by materials was 1.08%, and it increased as the washing frequency increased, compared to the grey fabrics, whereas the change rates of cotton and rayon were 0.74% and 0.22%, respectively. The qmax decreased in the order of cotton>tencel>rayon as the washing frequency increased.

• 한국의류학회지
• /
• 제20권6호
• /
• pp.975-982
• /
• 1996

This study was conducted to examine the fatigue phenomenon of mechanical properites in denim fabrics for slacks during repeated shear and tensile deformation by analysing the change in the basic dynamic properties of fabrics on the basic of experiments to obtain the basic data necessary to measure their fatigue. In addition, this study was carried out by allowing these denim fabrics at market to go through the repeated deformation under such different loads as 500 gf/cm2 and 1000 gf/cm2 by using a simulated fatigue tester, by calculating both dynamic properties and hand value (HV) of these fabrics with KES-F system and then by obtaining the THV through these calculated properties. The results are as follows: 1 The fatigue phenomenon of dynamic properties was remarkably shown by the repeated shear and tensile deformation, while the increase of hysterical plastic substances was also remarkable in these shearing and bending properties. 2. The elasticity values of tensile, bending and compression properties, such as, B and G were reduced: whereas RT and RC values increased. It was shown, then, that those fabrics lost their elasticity and became flexible and soft with the increase of fatigue. 3. The fatigue phenomenon of hand value also showed that those fabrics became soft in relation with the change of all dynamic properties, and that their performance was also change to flexible hand value. 4. TRhe degree of fatigue was also shown by the loads given to the repeated deformation. It was shown that the fatigue was higher for the tensile load of 1000 gf/cm3 than did the standard load of 500 gf/cm3 It is necessary, therefore, to consider the load in accordance with their usage when examining the fatigue phenomenon with respect to the dynamic properties of clothing materials. 5. The loads were nearly not influenced by the change in the general hand value tended to show a little of increase with the increase of fatigue, Based on those results, it seems that the fatigue phenomonon is related to the loads given to the repeated deformation.

• 한국의류학회지
• /
• 제11권3호
• /
• pp.79-88
• /
• 1987

In order to investigate the hand values and mechanical properties such as tensile, shearing, bending, compression, surface and thickness & weight of the women's summer fabrics were measured by KES-F system. Sorts of 78 commercial fabrics of women's summer cloth were classfied into 43 silk and 35 polyester fabrics according to materials. The experimental results were analysed statistically to relate the hand values and the mechanical properties and concerning to formation of weared clothes and transformation behavior were investigated. The main results are summarized as follows; 1. Polyester fabrics show higher tensile deformation than those of silk fabric. And also polyster fabric has a easy to shape-less and makes a silhouette which goes along with the body. 2. Silk fabrics is superior to polyester fabrics in formation and shear elasticity building box-shaped silhouette. 3. Polyester fabrics show sufficient ability to recover from tending deformation and drapability On the other hand, the compressibility and bending rigidity of silk fabrics were superior to polyester fabrics. 4. Regardless of materials, the bending properties is closely assocsiated with stiffness, anti-drape stiffness and flexibility with soft feeling. Fullness & softness and crispness is primarily influenced by surface properties. There is substantive relationship between scrooping and sheaing properties.

• Composites Research
• /
• 제23권5호
• /
• pp.8-14
• /
• 2010

서로 다른 길이비를 갖는 세 종류의 유리 직물 복합재료(평직, 균형능직, 비균형능직)의 면내 전단 물성 평가를 위해 편향인장 시험을 실시하였다. 직물 복합재료의 전단각을 결정하기 위하여 인장 변형량과 직물의 크기에 기인한 이론식, 직접측정법 및 이미지 분석법등을 이용하여 서로의 장단점을 비교하여 보았으며, 편향 인장 시험의 기하구조를 이용하여 유도된 식을 통해 면내 전단력을 계산하였다. 또한 트렐리스 시험(trellis-frame test)에 의한 결과와의 비교를 통해 편향 인장 시험에 의한 전단 물성 측정법의 정확도를 평가하였다. 실험 결과, 이론식에 의한 전단각 계산법은 전단각이 30도 이내일 경우에 이미지를 통한 직접 측정의 결과와 유사하였으며, 면내 전단력은 평직이나 균형 능직과 같은 등방형 직물의 경우에만 측정 샘플의 길이비에 무관한 균일한 결과를 보였다. 또한 편향 인장 시험과 트렐리스 시험 모두 비등방성이 큰 직물에 대한 전단 평가를 수행하는 데 있어서 많은 편차를 나타내었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.3-14
• /
• 2000

Anisotropic consolidation, shear, a transportational component during or after deposition each may produce anisotropic fabrics, which result in the anisotropic properties of soils. Nevertheless, the isotropically consolidated compression triaxial tests are commonly used in practice to determine the strength of the anisotropically consolidated soils because of their practicality and simplicity. In this paper the effects of anisotropic consolidation on the strength properties of soils are discussed. For the sandy soils consolidated under a constant vertical consolidation pressure, the deformation modulus decreases with decreasing consolidation pressure ratio($\sigma$$\sub$3c/'/$\sigma$ sub 1c/'), but the liquefaction resistance increases. For the saturated cohesive soils, both the undrained shear strength and undrained creep strength decrese with decreasing the consolidation pressure ratio. When the in-situ strength properties of the anisotropically and normally consolidated soils are determined by the isotropically consolidated tests, the undrained shear strength and creep strength of saturated cohesive soils as well as the deformation modulus of sandy soils are measured to be higher than the rear in-situ values. This, therefore, could lead to a dangerous judgement in stability analysis

• 패션비즈니스
• /
• 제17권6호
• /
• pp.28-43
• /
• 2013

Recent trends toward the collaborations among various sectors of academia and research areas have brought interests and significances in new activities especially in the fashion and textile areas. One of the collaboration examples is the recent research projects on 3D virtual clothing systems based on the 3D CAD software. The 3D virtual clothing systems provide simulated apparels with high degrees of fidelity in terms of color, texture, and structural details. However, since real fabrics exhibit strong nonlinearity, anisotropy, viscoelasticity, and hysteresis, the 3D virtual clothing systems need fine tuning parameters for the simulation process. In this study, characteristics of silk fabrics, which are woven by using degummed silk and raw silk yarns, are being analyzed and compared. Anisotropic properties may be measured as warp and filling direction properties separately in woven fabrics, such as warp tensile stress or filling bending rigidity. Hysteretic properties may be measured as bending hysteresis or shear hysteresis by using KES measurements. These data provide deformation-force relationships of the fabric specimen. Three-dimensional effects obtained when using these characteristic fabrics are also analyzed. The methods to control the three-dimensional appearance of the sewn fabric specimens when utilizing a programmable microprocessor-based motor device, as prepared in this study, are presented. Based on the physical and mechanical properties measured when using the KES equipment, the property parameters are being into a 3-dimensional virtual digital clothing system, in order to generate a virtual clothing product based on the measured silk fabric properties.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.99-102
• /
• 2003

This paper aims to observe the micro-mechanical behaviour of tow geometry during deformation of dry woven carbon-fiber fabric. With the increment of shear angle fabric experiences 'lock-up'phenomenon. In this paper, deformation of micro-mechanical parameters such as tow interval, change in tow amplitude and wavelength are investigated. To observe the micro-deformation of the fabric structure, appropriate specimens from bias extension and biaxial tests are sectioned and observed under the microscope. It was found that different loading conditions cause geometric deferences in the tow architecture.

• 자원환경지질
• /
• 제23권4호
• /
• pp.453-463
• /
• 1990

주향이동운동(走向移動運動)에 의해 발달된 예천(醴泉) 전단대(剪斷帶)는 쥬라기 구조운동(構造運動)과 동시(同時)에 화강암류(花崗岩類)가 정치(定置)된 후，비교적 고온상태(高溫狀態)에서 생성(生成)되었다. 전단대(剪斷帶)가 화강암류(花崗岩類) 정치(定置)후 발달(發達)하였음은 화강암체(花崗岩體) 내외(內外)에서 엽리(葉理)와 선구조(線構造)의 운결성(運結性), 분쇄질(粉碎質) 구조(構造)의 발달(發達)，페그마타이트와 규장암맥(硅長岩脈)의 변형작용(變形作用)，모암(母岩)에서 반장변정(班狀變晶)들의 구조전(構造前)(Pretectonic)성장(成長) 등에 의해 확인된다. 전단대(剪斷帶)의 다양한 전단감각(剪斷感覺) 지시자(指時者)들은 대부분 전단대(剪斷帶) 중심부(中心部)의 강변형암(强變形岩)에서 잘 관찰된다. 이들은 전단감각(剪斷感覺)이 S-C fabric, 형태(形態) 선택배향(選擇配向)，비대칭(非對稱) Porphyroclast system, Mica fish, 비대칭(非對稱) 신장구조(伸張構造)，결정축(結晶軸) 선택배향(選擇配向)둥에 의해 일관성(一貫性) 있게 우수향(右手向)(Dextral)임을 보여준다.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.316-320
• /
• 2004

Waterproof fabrics are seamed and sealed by waterproof sealing tape to prevent water from penetrating through the stitch holes. As this process may change the mechanical properties of breathable waterproof fabric related to its deformation with human body, the changes in mechanical properties were investigated. In both of parallel and perpendicular directions, tensile characteristics were remarkably changed with seaming and sealing processes. The increase of LT and WT means that the clothing sealed by waterproofing tape may produce somewhat discomfort feeling. On the other hand, the bridge of the sewing thread seemed to be reinforced by waterproofing tape. Shear characteristics such as G, 2HG, and 2HG5 gradually increased with seaming and sealing processes in parallel direction. However, they decreased with sealing process in perpendicular direction because the seam line would work as an axis located at the center of the testing range.

• Composites Research
• /
• 제20권3호
• /
• pp.1-7
• /
• 2007

본 연구는 전단농화유체(STF)가 함침된 Kevlar 복합재료(STF-Kevlar composite)의 제조 및 방탄성능 평가에 관한 내용이다. 전단농화유체는 fumed silica와 구형 silica를 에틸렌글리콜에 혼합하여 제조하였고 이 유체를 Kevlar직물에 함침시켜 액체방탄재료를 제작하였다. 전단농화거동을 조사한 결과 사용된 STF는 모두 전단농화거동이 발현됨을 확인하였다. 그리고 방탄시험 결과 구형silica STF-Kevlar 복합재료가 보다 우수한 방탄특성을 나타내었다. 한편 방탄시험 시 neat Kevlar 시험편에서는 탄자가 섬유를 pull-out하면서 관통하는 현상이 발생하였으나 LBA시험편에서는 섬유의 pull-out 대신 원주방향으로 섬유가 변형되면서 방탄재료가 변형되는 거동을 보여 서로 다른 변형거동을 각각 나타내는 것으로 관찰되었다.