• Journal of computational fluids engineering
• /
• v.20 no.4
• /
• pp.7-13
• /
• 2015

Vortex tube is a thermal static device that separates compressed air into hot and cold streams. In general, the cooling efficiency of vortex tubes is lower than that of traditional air conditioning equipment and vortex tubes are mainly used for industrial spot cooling applications because of their quick responses. In this study, conical frustums are employed in the nozzle chamber to improve the cooling performance. Conical frustums can be used to decrease the ineffective mass fraction that directly passes through the cold exit without energy separation. The shape optimization of conical frustums has been performed using full factorial design. It is found that the height of frustums has the largest main effects on the cooling performance. Computational results show that the cooling performance can be increased by about 10% within the considered range of the design parameters. This is because the ineffective mass fraction toward the cold exit is decreased by about 20%.

• Archives of Plastic Surgery
• /
• v.32 no.6
• /
• pp.791-795
• /
• 2005

A symmetric approach, using external rhinoplasty, is presented to aid the plastic surgeon in obtaining improved aesthetic and functional results in patients with postoperative nasal deformities. The external approach yields a full visualization of the underlying nasal framework and intraoperative evaluation of the deformities to be corrected subsequently. The nasal septal cartilage is unequivocally one of the best graft sources for reconstruction of the dorsum, columella or tip. It has fairly even surface and pliability in carving and shaping the graft. The graft can be obtained during the surgery with less morbidity and prepared easily for need of the shape. The only real disadvantage is the limited amount of cartilage that can be obtained from the septum. The dorsal and caudal rims, one or more cm in width, of the nasal septum should not be disturbed to maintain the nasal frame during harvesting the septal graft. Authors invented novel instruments, J & D knife and Flat (Spatula) suction tip, and have employed the devices for harvesting the septal cartilage. We were unable to gain enough amount of the cartilage by using a swivel knife or cartilage scissors. The septal cartilage can be resected as much as needed with newly invented instruments which facilitate a separation(method) technique.

• 한국해양학회지
• /
• v.28 no.1
• /
• pp.17-23
• /
• 1993

A right cylindrical tank with sloping bottom and top (${\beta}-effect$) is filled with two-layered fluid and is put on the rotating table. External fluid of same density as the lower-layer fluid is continuously injected to drive the lower-layer current. By minimizing the interfacial stress between two layers the motion in the lower-layer deformed the shape of interface such that the upper-layer adjust itself to the variations of the interface in terms of its direction of flow patterns .The most significant parameter is the internal Froude Number($F_1$) and when $F_1$ is greater than 6 two-cellular circulation of the upper-layer changes its direction, there by creates a separation of Western boundary current. The separation position moves to the most northward when $F_1$ equals to 6.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.261-264
• /
• 2010

Dual Pulse Rocket Motor is a solid rocket motor with two grains separated by a bulkhead and rupture disc. The elasto-plastic explicit dynamic analysis of rupture disc was conducted by the finite element method. The effect of the slit geometry of rupture disc with radial slit was parametrically analyzed in terms of rupture time and shape. The results can be used to control the rupture pressure by changing the slit geometry of rupture disc.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.105-112
• /
• 2010

Dual Pulse Rocket Motor is a solid rocket motor with two grains separated by a bulkhead and rupture disc. The elasto-plastic explicit dynamic analysis of rupture disc was conducted by finite element method. The effect of the slit geometry of a rupture disc was analyzed for rupture time and shape by the parametric study. The results can be used to control the rupture pressure by the change the slit geometry of a rupture disc.

• The Journal of Korea Robotics Society
• /
• v.11 no.2
• /
• pp.100-107
• /
• 2016

To realize a robot hand interacting like a human hand, there are many tactile sensors sensing normal force, shear force, torque, shape, roughness and temperature. This sensing signal is essential to manipulate object accurately with robot hand. In particular, slip sensors make manipulation more accurate and breakless to object. Up to now several slip sensors were developed and applied to robot hand. Many of them used complicate algorithm and signal processing with vibration data. In this paper, we developed novel principle slip sensor using separation layer. These two layers are moved from each other when slip occur. Developed sensor can sense slip signal by measuring this relative displacement between two layers. Also our principle makes slip signal decoupled from normal force and shear force without other sensors. The sensor was fabricated using the NBR(acrylo-nitrile butadiene rubber) and the Ecoflex as substrate and a paper as dielectric. To verify our sensor, slip experiment and normal force decoupling test were conducted.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.168-172
• /
• 2008

Three different geometry shapes of the blade leading edge in a centrifugal compressor were investigated in this paper. Numerical simulation was done to analyze the effect of the leading edge shape on the performance of the centrifugal compressor. The result shows that compared to the blunt leading edge, the circular leading edge will raise the chocking mass flow. The pressure ratio and efficiency will increase obviously. Using elliptical leading edge will get a further improvement on the performance than circular leading edge. The analysis of the flow field shows that the leading edge often causes flow separation near the inlet; using circular leading edge and elliptical leading edge will reduce the separation. What's more, using circular and elliptical leading edge will also reduce the wake loss near the outlet of the impeller. In a centrifugal compressor, using circular or elliptical leading edge on the splitter will improve the pressure loading distribution of main blade near the position of the splitter leading, which will increase the pressure ratio.

• Membrane Journal
• /
• v.29 no.4
• /
• pp.202-215
• /
• 2019

Molecular sieve membranes separate molecules based on their size and/or shape and have been of high interest, due to their potentially high energy efficiency and high selectivity. Zeolite MFI membrane is one of the most-studied molecular sieve membranes and has affected following studies on other molecular sieve membranes. This review discusses the technical developments on the control of morphology, microstructure, and defect of MFI membranes, which have significantly improved xylene isomer separation performances. These include crystal morphology control, effective secondary growth, seed coating method, crystal orientation control, heteroatom doping, and defect healing method.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.3
• /
• pp.275-284
• /
• 2022

Linear Shaped Charge(LSC) is widely used as a separation system in the field of weapon system. However, there are some disadvantages that are charging lots of explosives due to lack of uniformity and having difficulties of the design of liner and explosives because of manufacturing process. In order to solve these problems, Precision Linear Shaped Charge(PLSC) that can design a liner independently and charge explosives uniformly has been developed. In this study, PLSC was designed to have a proper liner shape and amount of explosives, and the penetration test of PLSC with different stand-off distance from liner to target was conducted. On the basis of the penetration test results of PLSC, the numerical analysis method using AUTODYN was established and verified. The penetrative mechanism and characteristics of PLSC with targets of different materials was analyzed from experimental and numerical results.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.5.2-5.2
• /
• 2009

From 10 years ago, the development of nano-devices endeavored to achieve reconstruction of information technology (IT) and nano technology (NT) industry. Among the many materials for the IT and NT industry, zinc oxide (ZnO) is a very promising candidate material for the research of nano-device development. Nano-structures of ZnO-based materials were grown easily via various methods and it attracts huge attention because of their superior electrical and optical properties for optoelectronic devices. Recently, among the various growth methods, MOCVD has attracted considerable attention because it is suitable process with benefits such as large area growth, vertical alignment, and accurate doping for nano-device fabrication. However, ZnO based nanowires grown by MOCVD process were had the principal problems of 1st interfacial layers between substrate and nanowire, 2nd a broad diameter (about 100 nm), and 3rd high density, and 4th critical evaporation temperature of Zinc precursors. In particular, the growth of high performance nanowire for high efficiency nano-devices must be formed at high temperature growth, but zinc precursors were evaporated at high temperature.These problems should be repaired for materialization of ultra high performance quantum devices with quantum effect. For this reason, we firstly proposed the growth method of vertical aligned slim MgZnO nanowires (< 10 nm) without interfacial layers using self-phase separation by introduced Mg at critical evaporation temperature of Zinc precursors ($500^{\circ}C$). Here, the self-phase separation was reported that MgO-rich and the ZnO-rich phases were spontaneously formed by additionally introduced Mg precursors. In the growth of nanowires, the nanowires were only grown on the wurzite single crystal seeds as ZnO-rich phases with relatively low Mg composition (~36 at %). In this study, we investigated the microstructural behaviors of self-phase separation with increasing the Mg fluxes in the growth of MZO NWs, in order to secure drastic control engineering of density,diameter, and shape of nanowires.