• Smart Structures and Systems
• /
• 제30권3호
• /
• pp.245-253
• /
• 2022

A two-layer beam consisting of an elastoplastic layer and a functional layer made of shape memory alloy (SMA) TiNi is considered. Constitutive relations for SMA are set by a microstructural model capable to calculate strain increment produced by arbitrary increments of stress and temperature. This model exploits the approximation of small strains. The equations to calculate the variations of the strain and the internal variables are based on the experimentally registered temperature kinetics of the martensitic transformations with an account of the crystallographic features of the transformation and the laws of equilibrium thermodynamics. Stress and phase distributions over the beam height are calculated by steps, by solving on each step the boundary-value problem for given increments of the bending moment (or curvature) and the tensile force (or relative elongation). Simplifying Bernoulli's hypotheses are applied. The temperature is considered homogeneous. The first stage of the numerical experiment is modeling of preliminary deformation of the beam by bending or stretching at a temperature corresponding to the martensitic state of the SMA layer. The second stage simulates heating and subsequent cooling across the temperature interval of the martensitic transformation. The curvature variation depends both on the total thickness of the beam and on the ratio of the layer's thicknesses.

• Corrosion Science and Technology
• /
• 제22권1호
• /
• pp.64-72
• /
• 2023

Ni-Ti shape memory alloy for dental nerve treatment devices was prepared by adding Mo to Ni-Ti alloy to improve flexibility and fatigue fracture characteristics and simultaneously increase corrosion resistance. Surface properties of the alloy were evaluated. Microstructure analysis of the Ni-Ti-xMo alloy revealed that the amount of needle-like structure increased with increasing Mo content. The shape of the precipitate showed a pattern in which a long needle-like structure gradually disappeared and changed into a small spherical shape. As a result of XRD analysis of the Ni-Ti-xMo alloy, R-phase structure appeared as Mo was added. R-phase and B2 structure were mainly observed. As a result of DSC analysis, phase transformation of the Ti-Ni-Mo alloy showed a two-step phase change of B2-R-B19' transformation with two exothermic peaks and one endothermic peak. As Mo content increased, R-phase formation temperature gradually decreased. As a result of measuring surface hardness of the Ti-Ni-Mo alloy, change in hardness value due to the phase change tended to decrease with increasing Mo content. As a result of the corrosion test, the corrosion potential and pitting potential increased while the current density tended to decrease with increasing Mo content.

• 대한건축학회논문집:계획계
• /
• 제35권8호
• /
• pp.3-14
• /
• 2019

The research is to track the morphological transformation of residential towers of apartment complexes in Busan. Though apartment is one of the most important components in Korean society, it has not drawn enough attention from academia as well as the public, especially regarding its shape. In result, its morphological change has barely been recognized. Instead, negative, but superficial, evaluation has become dominant tendency to deal with the shape of apartment tower. There are numerous 'partial' evidences to inform the morphological change of apartment plan type, and understanding the change is critical since morphological resultant reflects culture, politics, economy of a society. The research has been done on the 261 apartment complexes built through 2016 in Busan. The analysis shows that $I^0$ type, to represent 'typical boring architectural shape' of Korean apartments, has been dominant until the year 2000. However, its portion has become drastically decreased since the mid-2000. Composite plan type, the geometrical precedents of which had never been existent, emerged in the mid-2000, and this phenomenon may symbolize the change of morphology of apartment. When tower plan types are grouped together according to geometrical shape, three types, I-type, L-type and Y-type, take the most of residential towers, explaining 97% of the total. As expected, I-type is the most dominant, but its influence has decreased as time passes. Y-type might become one of the most important type in the period V. L-type has become the leading type in the Period VI to exceed I-type by 12 percent.

• 열처리공학회지
• /
• 제3권1호
• /
• pp.34-41
• /
• 1990

Effects of grain size and cold rolling degree on shape memory ability and transformation temperature were studied in Fe-35% Mn-6% Si shape memory alloy. Md point of the alloy was determined by variation of yield stress with test temperature. The Md point measured in this way was linearly increased with increasing grain size. Shape memory ability of the alloy was decreased with increasing grain size, showing a minimum value at around $63{\mu}m$, and then increased with increasing grain size. From this result, it was concluded that the shape memory ability in the grain size smaller than a critical value is controlled by amount of retained ${\gamma}$ and prior ${\varepsilon}$ phase, but that the shape memory ability in the grain size greater than the critical value is mainly dominated by grain boundary area in unit volume of parent phase. The shape memory ability was decreased with increasing deformation degree. This was because the ${\gamma}$ content being available for the formation of ${\varepsilon}$ martensite during bending was decreased with increasing deformation degree.

• Composites Research
• /
• 제17권5호
• /
• pp.54-60
• /
• 2004

복합재의 사전변형률과 형상기억합금의 형상기억효과를 유발하는 형상기억합금의 상변화량과의 관계를 예측하기 위하여 Eshelby의 등가개재물법과 Mori-Tanaka의 평균장이론을 이용한 새로운 3차원 모델을 제안하였다. 복합재 모델은 가공경화 현상을 갖는 알루미늄을 모재로, 단섬유 TiNi 형상기억합금을 강화재로 사용하였다. 모델 해석에 의하면 사전 변형률이 지극히 작은 영역에서는 사전변형률이 모두 강화재의 형상기억 효과를 유발하고, 이 보다 큰 영역에서 사전 변형률은 강화재의 형상기억 효과와 모재의 소성변형에 의한 것으로 나타났다. 이러한 복합재의 강화기구는 모재의 가공경화 현상과 형상기억 효과에 의한 항복응력 증가를 분리하여 제시되어야 한다.

• 한국세라믹학회지
• /
• 제33권4호
• /
• pp.448-454
• /
• 1996

BaTiO3 세라믹스의 입방정과 육방정간의 상전이에 따른 미세조직 변화를 관찰하였다. 입방정을 육방정영역에서 열처리하는 경우, 시편 표면부터 육방정상이 생성되었고 반대로 육방정을 입방정역에서 열처리하여 상전이 시킬때는 입방정상이 시편이 중심부에서부터 생성되었다. 또한 이러한 상전이 과정 중에는 빠른 입성장과 더불어 불규칙적인 입계형태를 나타내었다. 그 외 낮은 성형압으로 소결체의 밀도가 낮은 육방정 시편을 제조한 경우에는 상대적으로 입방정으로의 상전이가 억제되었다. 이러한 결과들은 육방정의 표면에너지가 입방정보다 상대적으로 낮기 때문으로 해석되었다.

• 한국안전학회지
• /
• 제19권4호
• /
• pp.1-7
• /
• 2004

This study investigated the effects of aging on the transformation behavior of $Ti-50.1at\%$ Ni alloy by means of differential scanning calorimetry. It was found that aging in the temperature range of $350^{\circ}C\~550^{\circ}C$ induced complex transformation behavior, involving the R-phase and multiple-stage martensitic transformation. Usually aged Ni-rich NiTi alloys undergo martensitic transformation on cooling from high temperatures in two step : B2 to R and then R to Bl9'(normal behavior). But under certain ageing conditions, the transformation can also occur in three or more step(unusual multiple step behavior). In the present study we use differential seaming calorimetry(DSC) for a systematic investigation of the evolution of transformation behavior with ageing temperature and time.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.191-191
• /
• 1990

• 정보처리학회논문지B
• /
• 제12B권5호
• /
• pp.527-534
• /
• 2005

영상에 회전이나 크기 변형이 가해지면 영상을 구성하는 점들의 좌표값들이 변경되어 형태 기술 및 인식이 어렵게 된다. 그러나 영상을 구성하는 점들 간의 위치관계나 무게중심과의 위치 관계는 변하지 않는다. 따라서 x-y 좌표계로 기술되는 영상 공간의 점들을 회전 및 크기 변형에 불변하는 새로운 좌표계로 사상할 수 있다면, 형태 기술 및 인식의 문제는 보다 수월해진다. 본 논문에서는 영상 공간의 점들을 회전 및 크기 변형에 무관한 새로운 특징 공간으로 사상하여 형태를 기술하는 방법을 제안한다. 특징 공간을 나타내는 새로운 좌표계는 무게중심으로부터의 상대거리와 윤곽선 세그먼트 곡률을 두 축으로 하는 직교 좌표계이다. 상대거리는 윤곽선 상의 임의의 한 점이 무게중심에서 얼마나 멀리 벗어나 있는지를 나타내는 값이고, 윤곽선 세그먼트 곡률은 세그먼트의 굴곡도를 나타내는 값이다. 특징 공간에 사상된 점들의 형태 기술은 메쉬 특징을 통해 이루어진다. 실험을 통해 제안된 형태 기술 방법이 회전 및 크기 변형에 강건함을 확인하였다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(2)
• /
• pp.842-845
• /
• 2005

A method for the numerical simulation of two-dimensional free-surface flow resulting from the propagation of regular gravity waves over topography with arbitrary bottom shape is presented. The method is based on the numerical solution of the Euler equations subject to the fully nonlinear free-surface boundary conditions and the appropriate bottom, inflow and outflow conditions using a hybrid finite-differences and spectral-method scheme. The formulation includes a boundary-fitted transformation, and is suitable for extension to incorporate large-eddy simulation (LES) and large-wave simulation (LWS) terms for turbulence and breaking wave modeling, respectively. Results are presented for the simulation of the free-surface flow over two different bottom topographies, with constant slope values of 1:10 and 1:20, two different inflow wave lengths and two different inflow wave heights. An absorption outflow zone is utilized and the results indicate minimum wave reflection from the outflow boundary. Over the bottom slope, lengths of waves in the linear regime are modified according to linear theory dispersion, while wave heights remain more or less unchanged. For waves in the nonlinear regime, wave lengths are becoming shorter, while the free surface elevation deviates from its initial sinusoidal shape.