• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.55-63
• /
• 2003

In a diesel engine, air-fuel mixture formation and ignition delay period have great influence on the performance of engine. Their main factors are combustion chamber shape, fuel injection system. air volume, air flow and so on. So, the combustion process in the cylinder is complex because of many factors which have direct and indirect effects on it. In this study, we take into consideration of scavenging pressure and scavenging temperature that are hewn as the main factor to the combustion process of two-stroke D.1. diesel engine. It is taken a picture of the combustion flame process for combustion chamber of re-entrant type and cylindrical type. So, it is applied to the basis data of combustion chamber design from an image analysis.

• Journal of ILASS-Korea
• /
• v.22 no.3
• /
• pp.116-121
• /
• 2017

Pre-combustion chamber type indirect diesel engines have different combustion characteristics compared with those of common rail direct injection engine. The CONVERGE, specific engine CFD program, was used to simulate hollow cone spray model and combustion. The air-fuel mixture flow propagating from pre-combustion chamber to cylinder was concentrated at top half and center of the pre-combustion chamber throat. Stronger mixture flow was formed at smaller and longer throat cases. As a result, thermal efficiency and fuel consumption were improved for modified throat shape and the soot emission was also reduced.

• Journal of Power System Engineering
• /
• v.2 no.2
• /
• pp.27-34
• /
• 1998

The purpose of this study is to investigate the performance of swirl combustion chamber diesel engine by changing the jet passage area and its angle, the depth and shape of the piston top cavity(main chamber). The performance of diesel engine with newly changed swirl combustion chamber was tested through the experimental conditions as engine speed, load and injection timing etc. The test results were compared and analyzed. The rate of fuel consumption was affected significantly by the jet passage area at the high speed and load, by the depth of the piston top cavity at the low speed and load. The exhaust smoke density and exhaust gas temperature depended sensitively on variation of the injection timing rather than the shape of the combustion chamber within the experimental conditions.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.1
• /
• pp.121-130
• /
• 1999

It is necessary to measure pressure, temperature, chemical equilibrium and the shape of flame in order to understand the combustion process in a combustion chamber. In particular, the flame formulation and combustion process of divided combustion chamber are different from those of a single chamber, And the variable diameter of a jet hole can effect not only physical properties like ejection velocity, temperature and time of combustion but also a chemical property like the reaction mechanism. Accordingly temperature is one of the most important factors which influence the combustion mechanism. This paper observed shape of flame by using the schlieren photographs and measured the pressure in a combustion chamber and the reaching time of the flame by ion probe By doing these, we investigation the formulation of the flame and the process of propagation. These measurement methods can be advanced in understanding the combustion process and process and propagation of flame.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.40-45
• /
• 1996

This Paper addresses to spray characteristics in w-shaped diesel engine combustion chamber which has impingement parts for 4 sprays injected from an injector. The two-dimensional shapes have been chosen to avoid the difficulties for analysing the spray dynamics in the real chamber. The simple shapes are reproduced with same geometries in vertical or horizontal sections through the impingement lands. The spray developments are visualized with a high speed drum camera and shadowgraphy optical system, and the droplet sizes are measured by Malvern system. The detailed discussions m made for the two different combustion chamber shapes, which are new w-shape using spray wall impaction and general w-shape. The results show that the spray characteristics of the new shape are superior to those of the general w-shape.

• Journal of ILASS-Korea
• /
• v.2 no.2
• /
• pp.8-15
• /
• 1997

Combustion chamber systems using spray impinged on walls have been studied for improving combustion characteristics in high speed direct injection diesel engines. The fuel spray injected in a small combustion chamber may be easily impinged and deposited on the wall. The fuel deposit has been considered as the cause for unburned emission due to difficulty of fuel-air mixing. In this paper w-shaped combustion chamber which has four raised pips on the side wall is introduced and discussed by comparing with conventional chamber with no pips. The computer code employing new spray-wall interaction model in general non-orthogonal grids is used in here. The model is applied into the new chamber shape with raised pips. In this chamber system four-hole nozzle is used, and the sprays injected from the each hole impact on lands raised from the chamber wall surface. After impacting, the sprays break up into much smaller drops and distribute over all the chamber space, instead of distributing just near the wall surface in conventional omega-shape. The results showed the potential of the w-shaped chamber employing pips for dispersing droplets so as tn avoid the fuel deposit regions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.220-231
• /
• 1996

In this research, we use IDI type constant volume combustion chamber which may make up stratified combustion to construct the design back data of lean-burn engine. Some experiments are conducted by the passagehole angle in the adapter of main chamber and sub-chamber. The effects on the combustion characteristics according to the ignition timing are investigated. The used fuel is methanol prospective for alternative fuel. Fuel is injected under 10.78MPa using solenoid and accumulator. As the results of the experiment, combustion characteristics reveals that ignition timing, passagehole angle and shape greatly effects on. Lean inflammability limit is extended to 0.45 in equivalence ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.99-106
• /
• 1999

The present study deals with the effect of combustion chamber shape on in-cylinder soot oxidation characteristics of a D.I . diesel engine. The analysed combustion chambers were a toroidal and a reentrant with a projection(Complex). The two-color method was used to measure in-cylinder flame temperature and KL value which is approximately proportional to the soot amount along the optical path. In addition, heat release rate was calculated from the in-cylinder pressure data. From these investigations , the soot oxidation of the reentrant and the complex which were strengthen squish flows went worse in late combustion period under heavy-load operation compared to that of the toroidal at retarded fuel injection timing . It might be the cause of the flame holding that squish lip depress the outflow of flame from the bowl to the entire combustion space.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.67-75
• /
• 2002

A study to investigate the influence of combustion chamber shape, especially piston top face configuration, on the combustion stability is presented with CFD analysis and single cylinder GDI engine test. Initial configuration of the piston bowl was designed with CFD analysis and further parametric studies of the design factors on the piston top face were carried out through the single cylinder GDI engine test. It was found that both the geometry of piston top face and the compression ratio have great influences on the combustion stability. Of interest is that the design factors of the GDI piston to prevent mixture diffusion out of the piston bowl have important roles for the stable combustion at the stratified mixture condition. Also the relationship between spray impingement and flow pattern in a GDI piston bowl should be considered to design an optimal bowl configuration for stable stratified combustion.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.328-340
• /
• 1991

The combustion process in the combustion chamber has been investigated by taking pressure, temperature, chemical equilibrium and the shape of flame. To predict temperature of a flame in a combustion chamber is one of very important problems in the field of combustion and the temperature is a important factor of ignition and counteraction to inflammation. In this paper, the flame temperature was determined by the method of the Rayleigh scattering of Ar-Ion Laser (514.5nm). The Rayleigh scattering has been got considerably attention because of its strong cattering intensity. As a result, it is shown that I can measure the shape of flame by schlieren photography and that I can get the flame temperature variation in constant volume combustion chamber by Laser Rayleigh Scattering.