• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1014-1017
• /
• 2007

Sound focusing technologies has been studied for various purposes from early 1990s. As a result, these technologies make us possible to apply in many uses. For example, we can treat tumors using focused ultrasonic waves without surgical knife and communicate in the ocean using time reversal array. Also applications for personal audio system become issues. Recently, as technologies are developing, in some applications, needs for regional focusing become increasing because previously suggested focusing methods, such as phase conjugation, time reversal and inverse filtering, were all about a point focusing. Therefore, studies on regional focusing method are essentially needed. Regional focusing method was firstly mentioned by Choi and Kim in 2002: acoustic contrast control. However, in regional focusing, physical interpretations between control variables and results are still not easy because of its complexity. In this regard, we tried to understand the relations between control variables and results in wavenumber domain and suggested a solution method for regional focusing: wavenumber spectrum matching. We also showed how to make spatially focused sound shape using the suggested method from the simplest case: line focusing.

• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.202-206
• /
• 2012

Marking is a process that engraves letters or a pattern onto the surface of sheet metal. During marking, it is important to set the proper working conditions for clarity of the letters. In this study a simple case for forming circular protrusions by half-piercing and embossing was initially attempted to determine the working conditions which gave good results with respect to shape accuracy. Corner-radius and flatness of circular protrusions made under several experimental conditions were measured and compared. It is shown that the precision of protrusions by half-piercing is superior to that of embossing, and the clearance between punch and die exerts a strong influence on the shape accuracy rather than the penetration percentage into the thickness of the sheet metal. The marking dies for "SNUT" letters, as an example, by applying the above results were manufactured with four different clearances. The working variables for the experiment were clearance and marking depth. For the very shallow depth of 0.1mm the letters were not clearly read. Letters marked under other conditions were easily distinguished with increasing marking depth. It was confirmed that the half-piercing technique with proper values of the working variables gives good quality for the marking of sheet metal.

• Korean Journal of Human Ecology
• /
• v.18 no.1
• /
• pp.259-273
• /
• 2009

The goal of this study is to analyze male college students' awareness and behaviors toward appearance management, and expenditure for appearance management. Male subjects' appearance management behaviors were focused on hair, skin, cosmetic surgery, fashion and body shape. A chi-square test, t-test, one-way ANOVA, Pearson's correlation analysis, multiple regression analysis were used. The major findings were as follows: (1) The mean of male college students' 'awareness toward appearance management' is 30.01(out of a possible 50). (2) The variables that significantly influenced their awareness toward appearance management are 'an allowance amount per month' and 'household income'. (3) Subjects' most preferred behavior is a variable of 'fashion care' in the appearance management(29.9%). (4) Appearance management behavior is different, according to demographic variables and awareness toward appearance management. (5) The mean of 'monthly expenditure for appearance management' is 247,194won. Consequently, the study shows that there is a most significant relation of 'awareness toward appearance management' to 'expenditure for appearance management'

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1314-1319
• /
• 2004

In this study, parameter optimization of micro-static mixer with a cantilever beam was accomplished for maximizing the mixing efficiency by using successive response surface approximations. Variables were chosen as the length of cantilever beam and the angle between horizontal and the cantilever beam. Sequential approximate optimization method was used to deal with both highly nonlinear and non-smooth characteristics of flow field in a micro-static mixer. Shape optimization problem of a micro-static mixer can be divided into a series of simple subproblems. Approximation to solve the subproblems was performed by response surface approximation, which does not require the sensitivity analysis. To verify the reliability of approximated objective function and the accuracy of it, ANOVA analysis and variables selection method were implemented, respectively. It was verified that successive response surface approximation worked very well and the mixing efficiency was improved very much comparing with the initial shape of a micro-static mixer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.55-58
• /
• 2003

Many researches have been already done on the issues of high temperature deformation and the microstructural evolution. The information has been very useful for the plasticity industry, especially successful for the extrusion. However, the parts made with forging usually have a complex shape. It is difficult to control the distribution of the variables like strain, strain rate and temperature rise due to the working heat during a hot-forging process. Consequently, the microstructural variation could be occurred depending on the plastic deformation history that the forged part would get during a hot forging. In the present study, the microstructural characteristic of a hot-forged 6061 aluminum alloy has been discussed on the aspect of grain size evolution. A forging of 6061 aluminum alloy has been carried out for a complex shape with a dimensional variation. Also, finite element analysis has been done to understand how the deformation variables such as strain, strain rate give an influence on the microstructure of a hot forged aluminum product.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.954-964
• /
• 1999

The effect of fabrication variables and microstructures on the compressive strength of open cell alumina zirconia and silicon nitride ceramics fabricated by polymeric sponge method was investigated. Bulk density and compressive strength of open cell ceramics were mainly affected by coating characteristics of ceramic slurry on polymeric sponge that controlled a shape thickness and defect of the struts. Sintering temperature was optimized for enhancement of strut strength and compressive strength of open cell ceramics. Relative density and compressive strength behaviors were relatively well matched with the predicted values. Open cell ceramics of lower relative density below 0.1 prepared by first relatively well matched with the predicted values. Open cell ceramics of lower relative density below 0.1 prepared by first coating of ceramic slurry had thin triangular prismatic struts that were often broken or longitudinally cracked. With an application of second coating of slurry shape of struts was transformed into thickner cylindrical one and defects in struts were healed but the relative density increased over 0.2 Open cell zirconia had both the highest bulk density and compressive strength and alumina had the lowest compressive strength while silicon nitrides showed relatively high compressive strength and the lowest density. Based upon the analysis open cell silicon nitride was expected to be one of potential structural ceramics with light weight.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1084-1092
• /
• 2006

Shape optimization of airfoil in WIG craft has been performed by considering the ground effect. The WIG craft should satisfy various aerodynamic characteristics such as lift, lift to drag ratio, and static height stability. However, they show a strong trade-off phenomenon so that it is difficult to satisfy aerodynamic properties simultaneously. Optimization is carried out through the multi-objective genetic algorithm. A multi-objective optimization means that each objective is considered separately instead of weighting. Due to the trade-off, pareto sets and non-dominated solutions can be obtained instead of the unique solution. NACA0015 airfoil is considered as a baseline model, shapes of airfoil are parameterized and rebuilt with four-Bezier curves. There are eighteen design variables and three objective functions. The range of design variables and their resolutions are two primary keys for the successful optimization. By two preliminary optimizations, the variation can be reduced effectively. After thirty evolutions, the non-dominated pareto individuals of twenty seven are obtained. Pareto sets are all the set of possible and excellent solution across the design space. At any selections of the pareto set, these are no better solutions in all design space.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.308-312
• /
• 1999

Developed the model equations which calculate roll force, roll power during hot rolling in real time. The variables which mainly effect on the roll force, roll power are shape factor, reduction, roll diameter, roll velocity, strip inlet temperature, carbon content of strip and strip-roll contact friction coefficient. Among these variables roll diameter, roll velocity, inlet temperature, carbon content and friction coefficient can be excluded in interpolated model equation by introducing equation of die force(F'), power(p') of the frictionless uniform plane strain compression which can be calculated without iteration. At the case of coulomb friction coefficient of 0.3, we evaluated coefficient of polynomial equations of {{{{ { F} over {F' } }}}}, {{{{ { Pf} over {Pd }, { Pd} over {P' } }}}} from the result of finite element analysis using interpolation. It was found that the change of values of {{{{ { F} over {F' }, { P} over {P' } }}}} with the friction coefficient tend to straight line which slope depend only on shape factor. With these properties, developed model equations could be extended to other values of coulomb friction coefficient. To verify developed roll force, roll power model equation we compared the results from these model equation with the results from these model equation with the results from finite element analysis in factory process condition.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.829-836
• /
• 2009

3-Dimensional flow which is represented by horseshoe vortex is generated as a type of secondary flow about the main flow. As well, it causes the flow loss. The present study deals with the leading edge fence shape on a wing-body junction to decrease a horseshoe vortex, one of the main factors to generate the secondary flow losses. The shape of leading-edge fence was optimized with the design variables of the installed height, length, width, and thickness of the fence as the design variables. Approximate optimization design method is used as the optimization. The study was investigated using $FLUENT^{TM}$ and $iSIGHT^{TM}$. Total pressure coefficient of the optimized design case was decreased about 7.5 % compare to the baseline case.

• Journal of the Korean Home Economics Association
• /
• v.38 no.10
• /
• pp.27-43
• /
• 2000

The CDP in Korea has been enforced for conserving resources and reducing environmental pollution since March, 1999. Therefore this thesis aims to investigate the degrees of consumer participation(CP), recognition and support, and to analysis of demographic variables, consumers' psychology, and attitudes which may influence the degrees of CP recognition, and support for the CDP. The results were as follows: First, the time of surrey was found to be statistically significant in consumer recognition and support. The degree of recognition was the lowest in first time. And the degree of consumer support was the highest in first time. Second, education, employment status and house shape were found to be statistically significant. The degree of consumer recognition was the highest among junior college graduates. The employed group was found to be the highest in the degree of participation. Third, the significant factors which influenced the degree of recognition was the time of survey, the perceived difficulty, effectiveness of the Consumer Deposit Program. The perceived difficulty, the time of survey were found to be related with the degree of consumer support. The most influential variables which influenced the degree of consumer participation were house shape, the perceived effectiveness, the degree of resource recycling, job and the degree of consumer recognition.