• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.555-560
• /
• 2000

This paper describes the macroscopic behavior and atomization characteristics of the high-pressure gasoline injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. The atomization characteristics of gasoline spray such as mean diameter and mean velocity of droplet were measured by the phase Doppler particle analyzer system. In order to obtain the influence of fuel injection pressure, the macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 3,5 and 7 MPa of injection pressure under different surrounding pressure in the spray chamber. The results of this work show that the fuel injection pressure of gasoline injector in GDl engine has influence upon the mean droplet diameter, mean velocity of spray droplet, the spray tip penetration, and spray width under the elevated ambient pressure.

• 대한조선학회논문집
• /
• 제53권4호
• /
• pp.300-306
• /
• 2016

The gas ventilated by supercavitation splits into smaller bubbles and follows the water passage of the cavitation tunnel. The bubbles quickly return to the test section by rather high speed flow, and interrupt the observation of the supercavitation. To secure clear observation in the test section, the bubble collecting section(settling chamber) of large volume is prepared to collect bubbles in the water passage ahead of the test section. The bubble collecting section should provide enough buoyancy effect to the bubbles for proper bubble collecting. However, rather high-speed oncoming flow produces non-uniform velocity distribution and deteriorates buoyancy effect in the bubble collecting section. In the present study, the bubble collecting space and three porous plates are designed and analyzed through numerical methods, and the bubble collecting function is experimentally validated by 1/10-scaled model in terms of the formation of uniformly low velocity distribution in the bubble collecting section.

• 한국분무공학회지
• /
• 제6권2호
• /
• pp.16-21
• /
• 2001

This paper describes the macroscopic behavior and atomization characteristics of the high-pressure gasoline swirl injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. The atomization characteristics of gasoline spray such as mean diameter and mean velocity of droplets were measured by the phase Doppler particle analyzer system. The macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 7 and 10 MPa of injection pressure under different spray cone angle. The results of this work show that the geometry of injector was more dominant over the macroscopic characteristics of spray than the fuel injection pressure and injection duration. As for the atomization characteristics, the increase of injection pressure resulted in the decrease of fuel droplet diameter and the atomization characteristics differed as to the spray cone angle. The most droplets had under $25{\mu}m$ diameter and for the large droplets(upper $40{\mu}m$) as the spray grew the atomization presses were very slow. Comparison results between the measured droplet distribution and the droplet distribution functions revealed that the measured droplet distribution is very closed to the Normal distribution function and Nukiyama-Tanasawa's function.

• 한국분무공학회지
• /
• 제10권4호
• /
• pp.47-53
• /
• 2005

This paper presents the effects of ambient pressure on atomization characteristics of high-Pressure injector in a direct injection gasoline engine both experimentally and numerically. The atomization characteristics such as mean droplet size, mean velocity, and velocity distribution were measured by phase Doppler particle analyzer. The spray development, spray penetration, and global spray structure were visualized using a shadowgraph technique. In order to investigate the atomization process numerically, the LISA-DDB hybrid model was utilized. This breakup model assumes that the primary breakup occurs when the amplitude of the unstable waves is equal to the radius of the ligament of liquid sheet near the nozzle and the droplet deformation induces the secondary breakup. The results provide the effect of ambient pressure on the macroscopic and microscopic behaviors such as spray development, spray penetration, mean droplet size, and mean velocity distribution. It is also revealed that the accuracy of prediction of LISA-DDB hybrid model is pretty good in terms of spray developing process, spray tip penetration, and SMD distribution.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.304-313
• /
• 1987

본 논문에서는 하부가열식 실험용 태양연못을 제작하여 열유속과 초기의 소금 농도구배를 변화시켜 가면서 실험을 수행하였다.실험을 통하여 측정한 각 층안의 온도와 소금농도구배 및 하부혼합층의 성장율 등을 바탕으로 지배방정식과 가정을 세 운뒤 이들 방정식을 풀어 실험테이터와 비교하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.486-491
• /
• 2008

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomizer internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD(Sauter Mean Diameters) distribution by using PLLIF(Planar Liquid Laser Induced Fluorescence) technique. The objectives of this research are getting a droplet distribution and drop size measurement of each condition and compare with the other flows effect. As the result, This research have been showed the droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects and normalized distance from the injector exit length.(x/d, y/d)There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.

• 한국해양공학회지
• /
• 제30권1호
• /
• pp.44-50
• /
• 2016

An experimental study was performed to investigate the behavior of green water on a structure with a rectangular cross section under wave conditions, along with the flow characteristics in bubbly water flow. An experiment was conducted in a two-dimensional wave flume using an acrylic model (1/125) of FPSO BW Pioneer operating in the Gulf of Mexico under its design wave condition. The occurrence of green water, including its development, in front of the model was captured using a high-speed Charge Coupled Device (CCD) camera with the shadowgraph technique. Using consecutive images, the generation procedure for green water on the model was divided into five phases: flip through, air entrapment, wave run-up, wave overturning, and water shipping. In addition, the distinct water elevations of the green water were defined as the height of flip through, height of splashing jet, and height of freeboard exceedance, and showed a linear relationship with the incoming wave height.

• 대한조선학회논문집
• /
• 제55권4호
• /
• pp.330-340
• /
• 2018

In the present works, the High-speed Cavitation Tunnel (HCT) has been designed and manufactured to have the large test section to conduct various supercavitation experiments. The large amount of air ventilated behind a cavitator produces lots of tiny bubbles, which prevent clear observation of supercavitation at the test section. To collect small bubbles effectively, a bubble collecting section of large volume is equipped upstream of the test section. HCT has the test section dimension of $0.3^H{\times}0.3^W{\times}3.0^L\;m^3$ and provides maximum flow speed of 20.4 m/s at the test section. The blockage and Froude effects on the ventilated supercavitation are investigated successfully at the test section. The basic studies such as the supercavitation evolution, drag measurements and cavity shape extraction with air flow rate are also carried out in HCT.

• 한국항공우주학회지
• /
• 제48권9호
• /
• pp.711-716
• /
• 2020

탄화수소계열 연료를 기반으로 혼합모사추진제를 사용하여 액적을 생성하고 열에너지를 가하면서 초임계 환경으로 분무되는 거동을 가시화하였다. 혼합모사추진제는 임계압력과 임계온도가 상이한 데칸과 메틸사이클로헥산을 선정하였다. 초임계 환경으로 분무되는 유동은 Rayleigh 분열로 액적을 생성하며 Oh 수와 Re 수를 구하여 Rayleigh 분열영역임을 확인하였다. 혼합모사추진제의 온도는 Tr=0.49에서 Tr=1.34까지 변화를 주었다. 유량은 0.7~0.8 g/s로 유지하였다. 액적은 열에너지를 가할수록 분열 길이가 짧아지며 덩어리진 형태로 떨어진다. 액체 상을 가시화하는 장치에서 2차 액적(second droplet)이 형성되는 것을 확인하였고 Tr=1.34일 때 부분적으로 불안정한 상태의 초임계 상태로 액상이 보이지 않는다.

• 한국추진공학회지
• /
• 제12권6호
• /
• pp.38-47
• /
• 2008

횡방향으로 유입되는 공기유동에서 연료 제트의 액주 및 액적영역의 궤적에 관한 연구를 수행하였다. 실험방법으로는 직접사진촬영방법과 평면레이저유도형광 기법을 사용하여 분석하였다. 본 연구의 목적은 공기유동 방향에 수직으로 분사되는 분무와 분사각도의 분무에서 궤적에 대한 경험식을 도출하여 기존 연구결과와 비교분석하고, 대향분사에서의 궤적에 대한 경험식을 도출하는데 있다. 실험을 통하여 액주 및 액적 영역의 궤적은 연료분사차압, 공기의 유속, 분사기 지름 크기, 분사각도에 의하여 결정되며, 정방향의 분무와 대향분사 결과에 있어서는 실험식 상수의 차이가 있음을 확인하였다.