• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.257-262
• /
• 2008

In this paper, we study the electric characteristics of shading effects in photovoltaic module in case of outdoor operation. When fabricating PV module, solar cells are connected serially to obtain the high voltage because of its low open circuit voltage. And total current is determined by lowest current among solar cells. When the shading happens on PV module's surface, the current of shaded solar cell determine the total current flow. Because of this, generally by-pass diode is installed on junction box. The bypass diode operate when revered and shaded solar cell's voltage is over 0.6 voltage. The reverse-biased solar cell gives reduced maximum power of PV module and might give negative effect on durability. So, adequate by-pass installation and selection is needed.

• 조명전기설비학회논문지
• /
• 제26권5호
• /
• pp.21-33
• /
• 2012

This paper presents the new maximum power point tracking(MPPT) control of the photovoltaic(PV) module integrated converter(MIC) system considering the shadow influence. The output characteristics of the solar cell is a nonlinear and affected by a temperature, the solar radiation and influence of a shadow. Particularly, MIC system is very sensitive to the shadow influence because the capacity is very small. In order to increase an output and efficiency of the solar power generation, the maximum power point(MPP) obeying control are necessary. Conventional perturbation and observation(PO) and Incremental conductance(IC) are the method finding MPP by the continued self-excitation vibration. The MPPT control is unable to be performed by rapid output change affected by the shadow. To solve this problem, the new control algorithm of the multi-level in which the step value changes by output change is presented. In case there are the solar radiation, a temperature and shadow influence, the presented algorithm treats and compares the conventional control algorithm and output error. In addition, the validity of the algorithm is proved. through the output error response characteristics.

• 한국농림기상학회지
• /
• 제23권4호
• /
• pp.283-294
• /
• 2021

경사면일사량은 수평면일사량과 해당위치 지형경사도 간의 기하학적 관계인 일사수광비율을 통해 추정할 수 있다. 그러나 이렇게 추정한 일사량은 주변에 햇빛을 차단하는 장애물이 없다는 것을 가정하기 때문에 만약 실제 농사를 짓고 있는 농장 등에 이를 적용할 경우에 지형으로 인한 차광 등의 영향을 충분히 반영하지 못한다. 음영기복도는 태양의 위치와 지형의 기복으로 인한 직달일사의 변이를 밝기(휘도)로 수치화한 격자 형태의 자료로서, 하나의 격자는 가장 어두운 값 0에서 가장 밝은 값 255까지의 값을 갖는다. 본 연구에서는 지형으로 인한 차광효과를 모의하기 위해 30m 해상도의 DEM을 이용하여 연구지역의 음영기복도를 제작하고 휘도 분석을 수행하였다. 연구지역에 설치된 AWS 22개 지점의 기상자료를 수집하여 일조율 80% 이상인 날을 선별하고, 관측일사량과 각 지점의 휘도를 비교하여 휘도가 지형으로 인한 차광효과를 설명할 수 있는지 확인하였다. 분석결과 휘도와 일사량 간에 상관관계가 있는 것을 확인하였으며, 지형의 영향이 큰 지점에서의 직달일사가 시작되는 시점과 끝나는 시점은 태양고도 보다는 휘도와 잘 부합하는 것으로 나타났다. 추가적인 연구를 통해 주변 지형의 영향을 반영한 휘도를 이용한 상세한 일사량 추정이 가능할 것으로 기대된다.

• 한국약용작물학회지
• /
• 제15권3호
• /
• pp.152-156
• /
• 2007

차광처리가 더덕의 생육 및 광합성에 미치는 영향을 구명하기 위하여 본 실험을 수행하였던 바, 그 결과는 다음과 같다. 1. 차광처리에 의하여 만장과 엽면적은 증가하였으나, 덩굴 및 잎의 건물증은 감소하였다. 2. 차광처리에 의하여 엽록소함량 및 비엽면적은 증가하였으나, 엽위별 일정한 경향이 없었고 상위엽보다는 하위엽에서그 증가 정도가 컸다. 3. 광합성속도와 기공전도도는 광 강도가 강할수록 또 차광일수가 경과할수록 증가하는 경향이었으며 그 증가 정도는 대체로 하위엽에서 크게 나타났다.

• 대한치과기공학회지
• /
• 제41권3호
• /
• pp.167-175
• /
• 2019

Purpose: This study was investigated the effect of multi-layer zirconia block type and design location on the mechanical properties of zirconia copings. Methods: Three kinds of multi-layered zirconia blocks (Snow princess multi layered block, Multi cherry, Dental zirconia pre-shaded blank) were used to identify the effects of the kinds of multi-layered zirconia blocks, design locations on mechanical characteristics of zirconia copings. 150 Zirconia copings were fabricated and fracture strength, hardness and microstructure were compared and evaluated. Results: Dental zirconia pre-shaded blank(2,256.9N) had the highest fracture strength of zirconia copings on all the design locations, and it was followed by Snow princess multi layered block(2,107.5N) and Multi cherry(917.0N). Snow princess multi layered block(1,949.7Hv) had the highest hardness of zirconia copings on all the design locations, and it was followed by Dental zirconia pre-shaded blank(1,671.7Hv) and Multi cherry(1,383.7Hv). The cervical layer had the highest fracture strength and hardness of zirconia copings in all the blocks, and it was followed by the cervical+gradation layer, the enamel layer, the enamel+gradation layer, and the gradation layer. Conclusion: It was found that the fracture strength and hardness were different according to the kinds of multilayer zirconia block and design location, and it was confirmed that it is lower than the fracture strength of white zirconia.

• Restorative Dentistry and Endodontics
• /
• 제48권1호
• /
• pp.7.1-7.10
• /
• 2023

Objectives: This study aimed to evaluate the surrounding and underlying shades' effect on the color adjustment potential (CAP) of a single-shade composite used in a thin layer. Materials and Methods: Cylinder specimens (1.0 mm thick) were built with the Vittra APS Unique composite, surrounded (dual specimens) or not (simple specimens) by a control composite (shade A1, A2, or A3). Simple specimens were also built only with the control composites. Each specimen's color was measured against white and black backgrounds or the simple control specimens with a spectrophotometer (CIELAB system). The whiteness index for dentistry (WI_D) and translucency parameters (TP₀₀) were calculated for simple specimens. Differences (ΔE₀₀) in color between the simple/dual specimens and the controls were calculated. The CAP was calculated based on the ratios between data from simple and dual specimens. Results: The Vittra APS Unique composite showed higher WID and TP₀₀ values than the controls. The highest values of ΔE₀₀ were observed among simple specimens. The color measurements of Vittra APS Unique (simple or dual) against the control specimens presented the lowest color differences. Only surrounding the single-shade composite with a shaded composite barely impacted the ΔE₀₀. The highest CAP values were obtained using a shaded composite under simple or dual specimens. Conclusions: The CAP of Vittra APS Unique was strongly affected by the underlying shade, while surrounding this composite with a shaded one barely affected its color adjustment.

• The Journal of Advanced Prosthodontics
• /
• 제6권5호
• /
• pp.415-422
• /
• 2014

PURPOSE. The purpose of this study was to evaluate and compare the translucency of shaded zirconia allceramic systems. MATERIALS AND METHODS. Translucency of 3 different zirconia all-ceramic systems colored by different techniques was compared with a lithium disilicate glass-ceramic (IPS e.max Press). Square-shaped specimens with 0.5 mm thickness were fabricated from In-Ceram YZ, ICE Zirkon and Katana systems in A1, A2 and A3.5 shades according to Vitapan Classical shade tab (n=11). Specimens were then veneered and glazed with corresponding veneer ceramic recommended by each zirconia system manufacturer and the total thickness was set to 1.5 mm. Translucency measurements were performed with VITA Easyshade Compact spectrophotometer after each stage and translucency parameter was calculated. Data were statistically analyzed with repeated measures ANOVA and Tukey multiple comparison test. RESULTS. The control group was significantly more translucent than the zirconia systems (P<.05). ICE Zirkon cores showed the least translucency; neither In-Ceram YZ nor Katana systems were superior to each other in terms of translucency. Translucency of all specimens was decreased after veneering, and the translucency rankings were changed. CONCLUSION. Coloring technique did not have a significant effect on translucency of zirconia cores. Although zirconia systems were less translucent than lithium disilicate glass ceramic, they had partial translucency and there were translucency differences among the zirconia systems. Chroma affected the translucency of precolored zirconia cores.

• Journal of Microbiology and Biotechnology
• /
• 제24권8호
• /
• pp.1034-1043
• /
• 2014

This study determined the effect of light intensity and photoperiod on the dry cell weight and total amount of carotenoids in four isolates of purple non-sulfur bacteria obtained from shaded and exposed microhabitats of a mangrove ecosystem in Kota Kinabalu, Sabah, Malaysia. The initial isolation of the bacteria was carried out using synthetic 112 medium under anaerobic conditions (2.5 klx) at $30{\pm}2^{\circ}C$. On the basis of colony appearance, cell morphology, gram staining, motility test, and 16S rRNA gene sequencing analyses, all four bacteria were identified as Afifella marina. One of the bacterial isolates, designated as Af. marina strain ME, which was extracted from an exposed mud habitat within the mangrove ecosystem, showed the highest yield in dry cell weight ($4.32{\pm}0.03g/l$) as well as total carotenoids ($0.783{\pm}0.002mg/g$ dry cell weight). These values were significantly higher than those for dry cell weight ($3.77{\pm}0.02g/l$) and total carotenoid content ($0.706{\pm}0.008mg/g$) produced by the isolates from shaded habitats. Further analysis of the effect of 10 levels of light intensity on the growth characteristics of Af. marina strain ME showed that the optimum production of dry cell weight and total carotenoids was achieved at different light intensities and incubation periods. The bacterium produced the highest dry cell weight of 4.98 g/l at 3 klx in 72 h incubation, but the carotenoid production of 0.783 mg/g was achieved at 2.5 klx in 48 h incubation. Subsequent analysis of the effect of photoperiod on the production of dry cell weight and total carotenoids at optimum light intensities (3 and 2.5 klx, respectively) revealed that 18 and 24 h were the optimum photoperiods for the production of dry cell weight and total carotenoids, respectively. The unique growth characteristics of the Af. marina strain ME can be exploited for biotechnology applications.

• Journal of Ginseng Research
• /
• 제21권2호
• /
• pp.115-118
• /
• 1997

Stratified American ginseng(Panax quinquefoilium L.) seeds were planted in a shaded greenhouse at four depths and in four different soil types to observe effects on emergence rate and root size. Seeding depth affected seedling emergence rates and the number of days required to complete emergence. The shape of the roots was affected by the texture of soil, especially percentage of sand.

• 아시안잔디학회지
• /
• 제20권1호
• /
• pp.25-31
• /
• 2006

'Meyer' zoysiagrass(Zoysia iaponica Steud.)는 일반적으로 미국 중부지역에서 골프장 페어 웨이 또는 티에 일반적으로 많이 쓰이는 잔디로 적은 시비와 관수와 함께 좋은 플래이를 제공한다. 하지만 그늘 지역에서의 생육이 저하되어 품질을 떨어뜨린다. 감소되어진 광량은 잔디 잎의 웃자람을 일으키며 밀도가 저하되고 약한 잔디 생육과 함께 답압이나 디보트에 따른 재생을 저하시킨다. 이 실험의 목적은 TE의 처리가 그늘 지역에서의 잔디의 웃자람을 억제하고 품질을 향상 시키는가를 알아보기 위함에 있다. 이 실험에서 두 가지 처리는 차광 조건(0%, 79%, 92% 차광막) 과 TE [0, 48(0.5x), $96g{\cdot}ha^{-1}\;a.i(1x)$]로 적용하였다. 무 차광 처리 시, 0.5x-비율로 TE처리에서 4 주후 무 처리구에 비해 18%의 잔디 예초물의 감소를 보였고 1x-비율의 TE 처리는 $30{\sim}38%$의 예초물 감소를 보였다. 매달 1x-비율의 TE 처리 시 무 차광 처리와 79% 차광에서 zosiagrass의 밀도를 증가 시켰다. 무 처리에 비해 두 TE 비율의 처리가 잔디의 웃자람을 감소시켰으며 1x-비율로 TE 처리 시 79% 차광에서 잔디 품질이 저하되는 것이 지연되었다. 이 실험에서 그늘진 지역에서의 TE 처리가 zoysiagrass 의 웃자람을 줄이고 잔디 품질을 향상 시킨다는 것을 알 수 있었다.