• Journal of Korean Institute of Industrial Engineers
• /
• v.15 no.2
• /
• pp.1-10
• /
• 1989

This paper deals with a single-facility multiproduction model concerning the basic cyclic scheduling. The aim is to obtain the production order of each product in a cycle and the cycle frequency for minimizing the setup costs and inventory carrying costs of all products. The problem is formulated by LP and it shows that the optimal solution derived dominates the solution of non-cyclic scheduling model on some conditions.

• International Journal of Reliability and Applications
• /
• v.17 no.1
• /
• pp.51-63
• /
• 2016

Stress function of ball bearing is function of multiple stochastic factors and this system is so complex that analytical expression for reliability is difficult to obtain. To address this pressing problem, in this article, we have made an attempt to approximate system reliability of this important item based on reliability bounds under the stress strength setup. This article also provides level of error of this item. Numerical analysis has been adopted to show the closeness between the upper and lower bounds of this item.

• Journal of KIISE:Computer Systems and Theory
• /
• v.26 no.12
• /
• pp.1529-1538
• /
• 1999

광대역 액세스 망은 B-ISDN 환경에서 다양한 유형의 가입자들을 서비스 노드로 집선하는 기능을 수행한다. ITU-T의 SG13에서는 광대역 액세스 망과 서비스 노드 사이에서 ATM 자원의 동적인 할당 및 해제를 위하여 연결 제어 프로토콜의 표준화를 수행하고 있다. ATM 연결의 설정을 위한 연결 제어 프로토콜과 신호 프로토콜의 연동 기능은 서비스 노드에서 수행되며, ITU-T에서는 순차적 연동 모델을 채택하고 있다. 순차적 연동 모델은 SN에서 각 프로토콜의 절차가 순차적 방식으로 연동되므로 연결 지연이 크다. 본 논문에서는 광대역 액세스 망의 도입으로 인한 연결 설정 지연을 최소화하기 위하여 병렬형으로 수행되는 연동 모델을 제시하였다. 그리고 본 논문에서 제안한 병렬형 연동 모델의 성능 분석을 통하여 순차적 연동 모델과의 연결 설정 지연 및 완료비에 대한 비교, 분석을 수행하였다. 성능 분석에서 사용된 워크로드 파라미터는 RACE MAGIC 프로젝트의 결과를 적용하였다. Abstract In B-ISDN environment, various subscribers are concentrated into a service node via a broadband access network. The SG13 of ITU-T is standardizing a connection control protocol which provides dynamic allocation of ATM resources between an access network and a service node. To establish an ATM connection, interworking functions between the connection control protocol and the signaling protocol are performed at the service node. ITU-T adopts the sequential interworking model. In this paper, we propose the parallel interworking model which minimizes the overall connection setup delay by introducing the access network. Using the performance analysis, we compare our proposed parallel model with the existing sequential model in terms of connection setup delay and completion ratio. The workload parameters of RACE MAGIC project are applied to the analysis and simulation.

• Steel and Composite Structures
• /
• v.6 no.2
• /
• pp.139-157
• /
• 2006

In this paper, a cyclic mechanical model is presented to simulate the behaviour of top and seat with web angle beam-to-column connections. The introduced mechanical model is compared with Eurocode 3 Annex J, its extension, and with experimental data. To have a better insight regarding the actual response of the joints, available results of the experiments, carried out on full-scale top and seat angle joints under monotonic and cyclic loading, are first considered. Subsequently, a finite element model of the test setup is developed. The application of the proposed model, its comparisons with the experimental curves and with the Eurocode 3 Annex J and with its modification, clearly show the excellent quality of the model proposed.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.772-776
• /
• 2004

This paper proposes an interference avoidance approach for Constraint-Based Routing (CBR) algorithm in the Multi-Protocol Label Switching (MPLS) network. The MPLS network itself has a capability of integrating among any layer-3 protocols and any layer-2 protocols of the OSI model. It is based on the label switching technology, which is fast and flexible switching technique using pre-defined Label Switching Paths (LSPs). The MPLS network is a solution for the Traffic Engineering(TE), Quality of Service (QoS), Virtual Private Network (VPN), and Constraint-Based Routing (CBR) issues. According to the MPLS CBR, routing performance requirements are capability for on-line routing, high network throughput, high network utilization, high network scalability, fast rerouting performance, low percentage of call-setup request blocking, and low calculation complexity. There are many previously proposed algorithms such as minimum hop (MH) algorithm, widest shortest path (WSP) algorithm, and minimum interference routing algorithm (MIRA). The MIRA algorithm is currently seemed to be the best solution for the MPLS routing problem in case of selecting a path with minimum interference level. It achieves lower call-setup request blocking, lower interference level, higher network utilization and higher network throughput. However, it suffers from routing calculation complexity which makes it difficult to real task implementation. In this paper, there are three objectives for routing algorithm design, which are minimizing interference levels with other source-destination node pairs, minimizing resource usage by selecting a minimum hop path first, and reducing calculation complexity. The proposed CBR algorithm is based on power factor calculation of total amount of possible path per link and the residual bandwidth in the network. A path with high power factor should be considered as minimum interference path and should be selected for path setup. With the proposed algorithm, all of the three objectives are attained and the approach of selection of a high power factor path could minimize interference level among all source-destination node pairs. The approach of selection of a shortest path from many equal power factor paths approach could minimize the usage of network resource. Then the network has higher resource reservation for future call-setup request. Moreover, the calculation of possible path per link (or interference level indicator) is run only whenever the network topology has been changed. Hence, this approach could reduce routing calculation complexity. The simulation results show that the proposed algorithm has good performance over high network utilization, low call-setup blocking percentage and low routing computation complexity.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.357-358
• /
• 2016

This paper presents a dynamic, electric-thermal model for a photovoltaic (PV) cell that combines electrical and thermal parameters. In this model, the irradiance and ambient temperature are used to calculate the PV cell temperature based on a five-layer thermal model. The cell temperature is then used in the electrical model to accurately adjust the PV cell output electrical characteristics and power. A custom experimental setup was built to test and verify the electrical and thermal characteristics of the PV cell and its surrounding layers. The electric-thermal model is validated using experimental data in realistic scenarios. This PV model can be scaled up and used to simulate PV systems in wide variety of applications, extreme environmental conditions, and fault conditions in real-time.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.12a
• /
• pp.57-63
• /
• 2004

various applications is presented. It is based on rapid-prototyping of transparent model for flow visualization and on the use of refractive index matching that enables efficient and clear visualization of the flow inside the model. The model is immersed in the index-matching fluid in a glass tank so that any displacement and rotation of the model in the tank have no influence on the optical setup for image acquisition to be made through a glass wall. This can facilitate greatly the camera calibration for stereo PIV and 3-D PTV. As the flow model is generated directly from 3-D surface data, no laborious preparation of the flow model is needed. This approach for seamless linking of model generation and PIV measurement is applicable to various flow measurements in automobile, ship building, fluid machinery, turbine, electrical appliances, heat exchanger, electronic cooling, bio-engineering and so on.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.105-109
• /
• 2013

There are the free space model, the direct-path and ground reflected model, Egli model, Okumura-Hata model in the representative propagational models. The measured results at the area of PNG area were used as the experimental data in this paper. The new proposed partial interval analysis method is applied on the measured propagation data in the cellular band. The interval for the analysis is divided from the entire 30 Km distance to 5 Km, and next to 1 Km. The best-fit propagation models are chosen on all partial intervals. The means and standard deviations are calculated for the differences between the measured data and all partial interval models. By using the 5 Km- or 1 Km- partial interval analysis, the standard deviation between the measured data and the partial propagation models was improved more than 1.7 dB.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.214-221
• /
• 1999

In this research, a power-assisted steering system is modeled as a part of a full vehicle dynamic model. The dynamic model of the steering system incorporates hydraulic and dynamic relations between major parts of a steering system, such as steering column, control valve, rack and pinion gear. Through an experimental setup of the steering system, the steering system model is validated. The steering model is included in a full vehicle dynamic model of a car, where kinematic relations between steering and suspension system are defined, and various simulations are performed to evaluate the performance of steering system in conjunction with overall dynamic performance of the vehicle.

• Nuclear Engineering and Technology
• /
• v.35 no.1
• /
• pp.35-44
• /
• 2003

The neutron induced nuclear data for Eu-153, Gd-155 and Cd-157 are calculated and evaluated in the high energy region. The evaluation procedure for deformed nuclei is setup by using Ecis-Empire codes. The energy dependent optical model potential parameters are searched based on the recent experimental data and applied up to 20 MeV. Optical model, full featured Hauser-Feshbach model and multistep direct and multistep compound model are used in the calculation. The direct-semidirect capture model and the direct coupled-channels contribution to discrete levels are introduced to improve the capture and inelastic scattering cross sections. The theoretically calculated cross sections are compared with the experimental data and the evaluated files. The model-calculated total and capture cross sections are in good agreement with the reference experimental data. The evaluated cross section results are compiled to ENDF-6 format and are expected to improve the ENDF/B-Vl.