• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.5
• /
• pp.919-926
• /
• 2023

In this paper, we implemented the surveillance camera system capable of day and night shooting. To this end, it is designed to capture clear images even at night using a CMOS image sensor as well as an IR-LED. In addition, a relatively simple motion detection algorithm was proposed through color model separation. Motions can be detected by extracting only the H channel from the color model, dividing the image into blocks, and then applying the block matching method using the average color value between consecutive frames. When motions are detected during filming, an alarm sounds automatically and a day and night motion detection system is implemented that can capture and save the event screen to a PC.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.3
• /
• pp.8-13
• /
• 2023

High bandwidth memory a core technology of the future memory semiconductor industry, is attracting attention. Temporary bonding and debonding process technology, which plays an important role in high bandwidth memory process technology, is also being studied. In this process, total thickness variation is a major factor determining wafer performance. In this study, the reliability of the equipment measuring total thickness variation is identified, and the servo motor settling, and wafer total thickness variation measurement accuracy are analyzed. As for the experimental variables, vacuum, acceleration time, and speed are changed to find the most efficient value by comparing the stabilization time. The smaller the vacuum and the larger the radius, the longer the settling time. If the radius is small, high-speed rotation performance is good, and if the radius is large, low-speed rotation performance is good. In the future, we plan to conduct an experiment to measure the entire of the wafer.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.3
• /
• pp.146-157
• /
• 2024

Despite numerous air mattresses marketed to prevent Pressure Ulcers (PU), none have fully succeeded due to residual pressure surpassing critical levels. We introduces an innovative medical bed system aiming at complete PU prevention. This system employs a unique 4-bar link mechanism, moving keys up and down to manage body pressure. Each of the 17 keys integrates a sensor controller, reading pressure from 10 sensors. By regulating motor input, we maintain body pressure below critical levels. Keys are equipped with a servo drive and sensor controller, linked to the main controller via two CAN series. Using fuzzy or PI/IP controllers, we adjust keys to minimize total error, dispersing body pressure and ensuring comfort. In case of controller failure, keys alternate swiftly, preventing ulcer development. Through experimental tests under varied conditions, the fuzzy controller with tailored membership functions demonstrated swift performance. PI control showed rapid convergence, while IP control exhibited slower convergence and oscillations near zero error. Our specialized medical robot bed, incorporating 4-bar links and pressure sensors, underwent testing with three controllers-fuzzy, PI, and IP-showcasing their effectiveness in keeping body pressure below critical ulcer levels. Experimental results validate the proposed approach's efficacy, indicating potential for complete PU prevention.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.379-382
• /
• 2007

The MEMS (Micro Electro Mechanical Systems) process is used in a micro/nano pattern manufacturing method. This method is based on the lithography technology. But the MEMS process has some problems such as complicated process, long processing time and high production costs. Many researchers are doing research in substitute manufacturing method to work out a solution to these problems. In this paper, we apply a dieless incremental forming technology to a substitute method of MEMS process. This dieless forming technology is using in the commercial scale sheet forming such as a prototype of automobile sheet parts. 5-axes CNC (Computerized Numeric Control) method are applied in this system to get a micro-scale dieless forming results. These 5-axes system are composed of precision AC servo motor stages (4-axes) and PZT actuator (1-axis). A PZT actuator is used in a precision actuating axis because it can be operated in the nano scale stroke resolution. This micro dieless incremental forming system has the advantage of minimization in manipulating distance and working space. As equipment and tools become smaller in size, minute inertia force and high natural frequency can be obtained. Therefore, high precision forming performance can be obtained. This allows the factory to quickly provide the customer with goods because the manufacturing system and process are reduced. To construct this micro manufacturing system, many technologies are necessary such as high stiffness frame, high precision actuating part, structural analysis, high precision tools and system control. To achieve the optimal forming quality, the micro dieless forming system is designed and made with high stiffness characteristic.

• 전자공학회논문지 IE
• /
• v.43 no.4
• /
• pp.28-36
• /
• 2006

In this paper, an algorithm to classify the 4 motions of arm and a control system to position control the prosthesis are studied. To classify the 4 motions, we use flex sensors which is electrical resistance type sensor that can measure warp of muscle. The flex sensors are attached to the biceps brchii muscle and coracobrachialis muscle and the sensor signals are passed the sensing system. 4 motion of the forearm - flexion and extension, the pronation and supination are classified from this. Also position of forearm is measured from the classified signals. Finally, A two D.O.F prosthesis arm with RC servo-motor is designed to verify the validity of the algorithm. At this time, fuzzy controller is used to reduce the position error by rotary inertia and noise. From the experiment, the position error had occurred within about 5 degree.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.6
• /
• pp.197-202
• /
• 2016

In this paper, we propose optimal smart home security monitoring system. Proposeed optimal smart home security system using the three types of ultrasonic sensors were tested to obtain reliable data. and Using Raspberry Pi3, the smart home security system was implemented. In addition, It was verified through experiments optimal efficiency with a small amount compared to the conventional sensor of the home security system by the two ultrasonic sensors located in the optimal position. It was able to use two ultrasonic sensors to determine whether the intruder's highly efficient and reliable intrusion, and connect the servo motor at the bottom of the camera so you can shoot adjusted to the attacker's location to shoot the intruder's image. In addition, by using a Web server and stored the recorded image and two ultrasonic sensor data and provide a Web page for a user to monitor at all remote locations.

• 한국HCI학회:학술대회논문집
• /
• 2008.02a
• /
• pp.534-539
• /
• 2008

This paper is about intelligent hexapod robot for the support walking of the aged person. The robot using various sensors and small camera has various abilities of forward backward walking, turing left or right, control the speed of walking, avoiding the obstacles and detecting risky situation of fire or gas. To let the aged feel soft and safe walking, we used special servo motor and developed hexapod walking mechanism and effective algorithm.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.4
• /
• pp.437-442
• /
• 2014

Recently, the needs for the development and application of the micro marine robot (MMR) which has the advantages in terms of size and cost are increasing. However, the basis is very short in the domestic. While the obstacle avoidance sonar (OAS) which was optimized in terms of size and performance and has the ability of 4-directional detection was developed for the obstacle avoidance of the micro surface robot (MSR) fortunately, the problem that the detection performance is degraded according to the shape of the obstacle because of using the fixed sonar-beam with the limited beam width and detection range exists. To solve this problem, the MSR mechanism that implements the rotating sonar-beam using the spur gear and the servo motor is proposed in this paper. To verify the performance of the proposed mechanism, the wall-tracking of the MSR is considered and the comparison and analysis in term of detection performance and actuation command is performed with conventional fixed sonar-beam. The test results show the validity of the proposed mechanism.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.2
• /
• pp.200-206
• /
• 2015

In order to verify the lift enhancement of the 2D hydrofoil with trailing edge rotor and check the ability of its practical use, experimental studies were conducted in the caviation tunnel using the test model with NACA0020 section. The three-component forces acting on the model could be measured by exclusively designed sting type multi-component load cell. The trailing edge of the model has been replaced with rotor which could be controlled by DC servo motor installed at the exterior of the tunnel. A typical effect of the trailing edge rotor has been introduced among the systematic experiments on various angular deviation of the model and the rotational velocity of the trailing edge rotor. It is appeared that the circulation control effect could be easily adjusted by selecting the rotational velocity of the trailing edge rotor and the lift force was augmented more than two times. Thus the proposed lifting device could be utilized as a novel high lifting device which has adjustability of lift force.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5440-5445
• /
• 2014

Many studies have examined robot control using human bio signals but complicated signal processing and expensive hardware are necessary. This study proposes a method to recognize a human's hand motion using a low-cost EMG sensor and Flex sensor. The method to classify movement of the hand and finger is determined from the change in output voltage measured through MCU. The analog reference voltage is determined to be 3.3V to increase the resolution of movement identification through experiment. The robotic hand is designed to realize the identified movement. The hand has four fingers and a wrist that are controlled using pneumatic cylinders and a DC servo motor, respectively. The results show that the proposed simple method can realize human hand motion in a remote environment using the fabricated robotic hand.