• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.261-264
• /
• 1995

A scheme of observer-based MFAC(Model Following Acceleration Control) system is proposed for the DC servo position control system. The proposed system is competed of MFAC, feedback controller, and reduced-order state observer. As the servo motor is controlled by the acceleration command, the total servo system becomes the acceleration control system. Simulation results show that the proposed system have robust properties against parameter variations and external disturbances.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.193-196
• /
• 2001

In this paper we designed CAMC-SP, the microprocessor embedded 2-axis motor control chip which controls a precise pulse motor by generating the pulse needed to control step motor, DC servo and AC servo motor. This design enables to decrease costs and to minimize a size. First we designed risc type 8-bit microprocessor compatible with PIC16C84, second we designed pulse motor controller. CAMC-SP is integrated of those two block. We designed CAMC-SP by VHDL and we testified to the Performance of it by performing functional simulation.

• Journal of the Korean Society of Industry Convergence
• /
• v.11 no.4
• /
• pp.209-216
• /
• 2008

The ball screw position control system driven by a pneumatic motor using continuous sliding mode is proposed. The design and performance of proposed servo system are presented by means of examples tested under practical service conditions. Results of experimental implementation on the proposed system illustrate the effectiveness of the ball screw position control system driven by a pneumatic motor using continuous sliding mode as a servo pneumatic actuator driven by a pneumatic motor.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.4
• /
• pp.235-245
• /
• 2004

In this paper, fault tolerant mechanisms are presented for a servo manipulator system designed to operate in a hot cell. A hot cell is a sealed and shielded room to handle radioactive materials, and it is dangerous for people to work in the hot cell. So, remote operations are necessary to handle the radioactive materials in the hot cell. KAERI has developed a servo manipulator system to perform such remote operations. However, since electric components such as servo motors may fail by radiation, fault tolerant mechanisms have to be considered. For fault tolerance of the servo manipulator system, duplication mechanism increasing the reliability of the transport's driving motors and reconfiguration algorithm accommodating the slave's motor failure have been presented. The reconfiguration algorithm recovering the end effector's motion in spite of one motor's failure is based on control allocation redistributing redundant axes. The constrained optimization method and pseudo inverse method have been adopted for control allocation. Simulation examples and real test results have been presented to verify the Proposed methods.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.599-602
• /
• 1999

In this paper, we attempt to control the pressure between two specimens using a servo gun in the resistance spot welding process. Servo guns have some advantages over pneumatic guns in that the fast response, the precise position control, and the accurate torque control are assured by virtue of the servo motor control. To demonstrate the practical significance of our results, we present some experimental results..

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.812-814
• /
• 1999

In this paper, we are applied the Genetic Algorithm (GA) to design of fuzzy logic controller (FLC) for a DC Servo-Motor Speed Control. GA is used to design of the membership functions and scaling factor of FLC. To evaluate the performances of the proposed FLC, we make an experiment on FLC for the speed control of an actual DC servo-motor system with nonlinear characteristics. Experimental results show that proposed controller have better performance than those of PD controller.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.29-32
• /
• 1989

This paper proposes new position control method for DC servo motor by PI controller adopting sliding mode control. By adding sliding mode controller to conventional PI controller good robustness is obtained with good transient response and no steady state error which are merits in PI controller. In order to use microprocessor for digital control the principles of sliding mode control conventionally explained in continous-time system are extended to discrete-time system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1207-1212
• /
• 2011

This paper presents a study on the DSP(Digital Signal Processor) controller for the PBW(power-by-wire) system using BLDC(Brushless Direct Current) servo motor pump. The PBW hydraulic actuator was realized with hydraulic pump driven by BLDC servo motor, hydraulic cylinder and controller. This PBW system needs speed control of servo motor for linear thrust action of hydraulic cylinder. This paper implements a servo controller with vector control algorithm and MIN-MAX PWM technique. As CPU of a controller, TMS320F2812 DSP was adopted because it has PWM waveform generator, A/D converter, SPI(Serial Peripheral Interface) port and many input/output port etc.

• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.206-213
• /
• 2011

A flexible die, which is composed of a number of punches with adjusted heights to form a three-dimensional curved surface, is a crucial part of a flexible forming technology. In this study, the punch and control system of the flexible die were designed. The flexible die is divided into three modules, namely, punch, control and joint, and the corresponding modules were developed. The punch module materializes a three-dimensional forming surface by the control module, which is composed of an AC servo motor set and a linear guide. The joint module is necessary for the sequential motion between the servo motor set and the punch module. A sequential motion algorithm for the AC servo motor set, that uses the data of the punch relative heights, was also proposed. Finally, a flexible stretch forming test was carried out using the presently designed flexible die.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.4
• /
• pp.351-361
• /
• 1996

A variable structure controller is developed for an AC servo motor used in CNC milling machines. The designed controller is implemented as an outer loop controller to a factory designed motor-servopack system. The robustness parameter is tuned for a fast response when the speed tracking error is large, while it is tuned for small oscillations when the speed tracking error is small. The designed controller is installed on a CNC machine using a PC. Cutting experiments show improved performance over the factory-designed controller.