• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.315-317
• /
• 2003

This paper deals with the position control of an AC servo motor using linear hall-effect sensors. The price of these is very low, but it is possible to make position control of motor similar to a control using an encoder. This paper introduces the design of motor using linear hall-effect sensors and shows the results of control.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.11
• /
• pp.1179-1182
• /
• 2011

RC servos are electro-mechanical devices that respond to a control signal, which instructs them to move their output shaft to a certain position. A servo is normally plugged into a radio receiver with a three pin connector. The three wires are a power (usually 4.8V to 6.0V), a ground, and a signal wire. The signal wire carries a PWM (Pulse-Width Modulation) signal consisting of a 1-2msec pulse repeated 50 times a second. A 1.5msec pulse will tell the servo to move to its output shaft to the center position, 0 degrees. For a servo with a 180 degree of motion, a 1msec pulse will move the servo to -90 degrees, and a 2msec pulse will move the servo to +90 degrees. In order to development a humanoid robot, mechanical design, fixtures design, analysis of kinematics, implementation moving program, selection of RC servo motor and controller are required. This study was performed to experimentally compare the rotation range of RC servo motors according to change of a periods.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.8
• /
• pp.1685-1691
• /
• 2004

The objective of this study is aimed at reducing the contour error of AC Servo derives by improving the interpolation error of each axis through variable structure control system. The errors in machining process by AC Servo motor are due to many elements, such as the delay of the servo drivers, friction and the gain mismatch between x axis and y axis motors and so on. Sliding mode control system is applied to a AC servo drive as a numerical example in this paper. The experiment results which are compared with those of typical PI scheme show the validity of improvement in circular interpolation error of the system.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.28-31
• /
• 1988

This paper proposes a new linear adaptive position controller of DC servo motor. The proposed method can improve the drive performance and rapidly reject the state error caused by both parameter variations and force disturbance. The structure of this adaptive control method is based multiloop feedback control and model reference control. Simulation results are presented to verify the improved response when parameter variations and load disturbance give relatively significant effects to the servo system.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.249-252
• /
• 2002

For a precise position control with the resolution of a micrometer, a dual servo system is constructed using a linear motor and a piezoelectric actuator. The switching mode dual servo algorithm is implemented on a DSP board in which A/D and D/A converters are also mounted. It is shown by the experimental results that the precise position control is performed within a few micrometer of position error by using the dual servo system.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.190-196
• /
• 2001

The naval vessel must moves rolling, pitching, yawing by wave when it runs in ocean. Some narrow beam antenna needed position compensation by stabilizer or gimbal for best performance. This paper presents the precision position control for heavy weight(130kg) in roll and pitch direction. Generally it's called for gimbal. This gimbal uses P-I controller, and it's driven by linear actuator and servo motor. This gimbal gets ship's gyro signal and synchro, which have the absolute angle value. Some other similar equipments are driven by huge hydraulic power, but this gimbal is driven by small servo motor. This control loop gets the following procedure repeatedly; reading ship gyro and gimbal synchro, calculating compensated error and control output, driving motor and actuator The performance of gimbal system was satisfied.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1044-1047
• /
• 1996

In this paper, GMDH(Group Method of Data Handling) algorithm, which is based on heuristic self organization to predict and identify the complex system, is applied to the control system of DC servo motor. The mathematical relation between input voltage and motor speed is obtained by GMDH algorithm. A design method of model following control system based on GMDH algorithm is developed. As a result of applying this method to DC servo motor, the simulation and experiment have shown that the developed method gives a good performance in tracking the reference model and in rejection of disturbance, in spite of constant load and changing load.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.170-173
• /
• 2005

This paper presents an Fuzzy-Neuro Observer system for an ac servo motor dirve to track periodic commands using a neuro-fuzzy observer. AC servo motor drive system is rather similar to a linear system. However, the uncertainties, such as machanical parametric variation, external disturbance, uncertainty due to nonideal in transient state. therefore an intelligent control system that isan on-line trained neural network controller with adaptive learning rates.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.245-247
• /
• 1992

We utilize as a processor TMS320C25 (Texas Instrument) in making a driver for a 4 pole PM synchronous servo motor. TMS320C25 has a 32bit ALU and a 16 bit hardware multiplier, and the maximum instruction execution rate is 10MIPS at 40MHz. We adopted a space vector modulation PWM method. An interesting point of this work is that PWM wave is generated by utilizing timer interrupts. Hence, in the rest of time the processor can take care of the other routine such as Park's coordinate transformation and the computation required in the feedback loops. Thus, it mates the hardware circuit very simple. Due to the decrease in the number of components, the motor drive system becomes more fault-tolerant and cost-optimized. Also, more flexibility is gained in changing the control parameters.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.313-315
• /
• 2009

In this thesis, A methodology of system implement for PID controller, PWM logic, HSC logic, Host Communication and external DAC interface are implemented into single FPGA chip is proposed. The implemented system is used to control the speed of DC servo motor. A DATA block transfers set point value(SV) and P, I, D gain parameters to the corresponding Blocks respectively by the Host Communication to Computer. A HSC block generates process value(PV) by a pulse and $90^{\circ}$ shifted pulse from the encoder A PID block makes error(E) signal from the set value and process value and output manufacture value(MV) through the PID controller. In PWM block using the MV from the PID block, drives H-bridge controlling the Motor. Also DAC interface controls the DAC to graph the digital signal such as SV, PV, E, MV in FPGA onto the Oscilloscope.