• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.9
• /
• pp.946-951
• /
• 2009

The small multi-jointed robots for most education are developed with the way of firmware. But the firmware may be very difficult to develop as gradually increasing throughputs and control routines. Due to limit of firmware we try to use on RTOS, but hard to adapt on the small multi-jointed robots. It would be hard to install RTOS into the small multi-jointed robots because of the size capacity of RTOS, and lack of libraries for control of the particular hardware. Moreover, even its RTOS with many functions causes its to make overheads scheduling, TCB (Task Control Block), and task states. Also to keep maintenance of RTOS, it is composed of components for the whole structure of my proposed RTOS. Additionally, We provided with libraries of servo motor and sensor control and developed RMS (Rate Montonic scheduler) to handle tasks on real time and reduce overheads. Therefore, It is possible to work the fixed priority and task preemptive way. We show one example of the multi-jointed robot installed with my proposed RTOS, which shows to obstacle avoidance and climbing up the slope.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.5
• /
• pp.543-547
• /
• 2009

This paper describes the design, simulation, development, and experiment of a six degree-of-freedom micropositioning parallel manipulator. A movable stage was supported with six links, each of which extends with a dc-servo micropositioning actuator. In case of parallel manipulator, while the solution of the inverse kinematics is easily found by the vectors of the links which are composed of the joint coordinates in base and platform, but forward kinematic is not easily solved because of the nonlinearity and complexity of the parallel manipulator's kinematic output equation with the multi-solutions. The movable range of the prototype was ${\pm}25mm$ in the x- and y-directions and ${\pm}12.5mm$ in the z-direction. The minimum incremental motion of the prototype was $1{\mu}m$ in the x- and y-directions and $0.5{\mu}m$ in the z-direction. The repeatability of the prototype was ${\pm}2{\mu}m$ in the x- and y-directions and ${\pm}1{\mu}m$ in the z-direction. The motion performance was also evaluated by not only the computer simulation of CAD model but also the experiment using a capacitive sensor system.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.7
• /
• pp.86-94
• /
• 1998

The rosette-scan seeker is a device mounted on the infrared guided missile. It offers the positions and iamges of target to missiles servo system by scanning a space about target in rosette pattern with a single detector. An instantaneous field of view (IFOV), which is a diameter of a detector moving along the path of the rosette pattern, has the property that its smaller size provide the less interference of background signals and detector noise. If its size is too small to voer the total field of view (TFOV), however, it produces the invisible regions in the TFOV. In this case, the invisible regions cause the performance of the seeker to deteriorate. For full scan-coverage, it is necessary to design the small IFOV without the invisible regions in the TFOV, as possible. In this paper, we propose the new method of designing the smaller IFOV than the conventional method and verify full coverage of the scanned region. By comparing the nose equivalent flux density (NEFD) of the proposed method with the that of the conventional one, we confirm that the former is better than the latter in terms of performance.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.216-224
• /
• 2013

This paper describes dual inverter drive for a fractional-slot concentrated winding permanent magnet synchronous machine (PMSM). PMSMs are widely used in many applications from small servo motors to few megawatts generators thanks to its high efficiency and torque density. Especially, fractional-slot concentrated winding PMSM is very popular in the applications where wide operation range is required because it shows very wide constant power speed ratios. High speed operation, however, requires lots of negative daxis current for reducing back-EMF regardless of output torque. Field weakening current does not contribute to the torque generation in surface mounted PMSM case and causes inverter and copper loss. To reduce the losses from field weakening current, this paper proposes PMSM with split stator and parallel dual inverter drive. Proposed parallel dual inverter drive reduces back-EMF and enables efficient drive at high speed and light load situation. Control strategy of proposed dual inverter system is established through loss analysis and simulation. Proposed concept is verified with practical experiment.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.2
• /
• pp.20-25
• /
• 2007

This paper describes a second-generation dual sine-grid surface encoder for 2-D position measurements. The surface encoder consisted of a 2-D grid with a 2-D sinusoidal pattern on its surface, and a 2-D angle sensor that detected the 2-D profile of the surface grid The 2-D angle sensor design of previously developed first-generation surface encoders was based on geometric optics. To improve the resolution of the surface encoder, we fabricated a 2-D sine-grid with a pitch of $10{\mu}m$. We also established a new optical model for the second-generation surface encoder that utilizes diffraction and interference to generate its measured values. The 2-D sine-grid was fabricated on a workpiece by an ultra precision lathe with the assistance of a fast tool servo. We then performed a UV-casting process to imprint the sine-grid on a transparent plastic film and constructed an experimental setup to realize the second-generation surface encoder. We conducted tests that demonstrated the feasibility of the proposed surface encoder model.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.147-157
• /
• 2003

The characteristics of a rock joint which influence the stability of rock mass structures such as cut slopes and tunnels are largely controlled by the conditions of the rock joint as well as its boundary conditions. The conditions of rock joints comprise asperity strength, roughness, and filling materials. Boundary conditions can be represented by assuming that the deformability(or stiffness) of the rock mass surrounding the joints is modelled by a spring with stiffness. A new direct shear apparatus was developed in this study, which adapts a servo control system using PID algorithm. This apparatus can be used to investigate the various aspects of shear characteristics of the rock joints at conditions of constant normal stress and constant normal stiffness and so on. The test results for saw-cut teeth joints show that shear strength should be evaluated by considering its specific boundary conditions far the design of tunnels and cut slopes.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.7 no.5
• /
• pp.46-50
• /
• 1997

In fuzzy logic control, static fuzzy rules cannot cope with significant changes of parameters of plants or environment. To solve this prohlem, self-organizing fuzzy control. neural-network-hased fuzzy logic control and so on have heen introduced so far. However, dynamically changed fuzzy rules of these schemes may make a fuzzy logic controller Fall into dangerous situations because the changed fuzzy rules may he incomplete or inconsistent. This paper proposes a new adaptive filzzy logic control scheme using a predictivc neural network. Although some parameters of a controlled plant or environment are changed, proposed fuzzy logic controller changes its decision outputs adaptively and robustly using unchanged initial fuzzy rules and the predictive errors generated hy the predictive neural network by on-line learning. Experimental results with a D<' servo-motor position control problem show that propnsed cnntrol scheme is very useful in the viewpoint of adaptability.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.8
• /
• pp.557-564
• /
• 2000

A very simple control approach using neural network for the robust position control of a Permanent Magnet Synchronous Motor(PMSM) is presented. The linear quadratic controller plus feedforward neural network is employed to obtain the robust PMSM system approximately linearized using field-orientation method for an AC servo. The neural network is trained in on-line phases and this neural network is composed by a feedforward recall and error back-propagation training. Since the total number of nodes are only eight, this system can be easily realized by the general microprocessor. During the normal operation, the input-output response is sampled and the weighting value is trained multi-times by error back-propagation method at each sample period to accommodate the possible variations in the parameters or load torque. In addition, the robustness is also obtained without affecting overall system response. This method is realized by a floating-point Digital Signal Processor DS1102 Board (TMS320C31).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.3
• /
• pp.295-302
• /
• 1998

In this paper, a new auto-tuning PI controller for the speed servo system of a PMSM is designed by using limited step response characteristics. The method is proposed that gets information about auto-tuning of PI regulator by the injection of step input, called limited input, during a transient response time of control. System parameter estimation and speed control could be continuously executed. This means that in despite of system uncertainty the system information obtained by limited input can be continuously applied to the PI regulator. We demonstrate the effectiveness of the proposed auto-tuning algorithm through simulation and experiment result of the speed control for a PMSM having monotone increasing step response.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.124-129
• /
• 2005

This paper presents an advanced method for an initial pole position estimation of a Permanent Magnet Linear Synchronous Motor(PMLSM) that has an accurate incremental encoder for servo applications but does not have Hall sensors as a magnetic pole sensor. By appropriately using the secant method as a numerical method the proposed algorithm finds either of two zero force positions and then the correct d-axis by applying a q-axis test current. It only requires the tuned current controller and the relative position information md so it can be simply applicable to a rotary PMSM. The experimental results show the validity of the proposed method, which has an excellent performance with respect to an accurate pole position estimation under the minimal moving distance(average of about 85㎛) during the estimation process.