• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.6
• /
• pp.1169-1174
• /
• 2011

CdTe thin-film solar cell technology is well known that it can theoretically improve its conversion efficiency and manufacturing costs compared to the conventional silicon solar cell technology, due to its optical band gap energy (about 1.45eV) for solar energy absorption, high light absorption capability and low cost requirements for producing solar cells. Although the prior studies obtained the high light absorption, CdTe thin film solar cell has not been come up to the sufficient efficiency yet. So, doping method was selected for the improvement of the electrical characteristics in CdTe solar cells. Some elements including Cu, Ag, Cd and Te were generally used for the p-dopant as substitutional acceptors in CdTe thin film. In this study, the sputtering-deposited CdTe thin film was immersed in $AgNO_3$ solution for ion exchange method to dope Ag ions. The effects of immersion temperature and Ag-concentration were investigated on the optical properties and electrical characteristics of CdTe thin film by using Auger electron spectroscopy depth-profile, UV-visible spectrophotometer, and a Hall effect measurement system. The best optical and electrical characteristics were sucessfully obtained by Ag doping at high temperature and concentration. The larger and more uniform diffusion of Ag ions made increase of the Ag ion density in CdTe thin film to decrease the series resistance as well as mede the faster diffusion of light by the metal ions to enhance the light absorption.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.6
• /
• pp.1349-1354
• /
• 2011

In this work, we fabricated the CdZnS/CdTe heterojunction and investigated the C-V characteristics to determine the depletion width and the charge density distribution. A parallel experiment on CdS/CdTe heterojunction was also carried out for comparison. The depletion region width, for CdZnS/CdTe heterojunction, was nearly constant, regardless of bias voltage. However, the depletion region was wider than that of CdS/CdTe heterojunction due to high resistivity of CdZnS film. The interface charge density of CdZnS/CdTe heterojunction was increased linearly with the bias voltage and showed lower values than those for CdS/CdTe junction. The open circuit voltage of CdZnS/CdTe heterojunction solar cells increased with zinc mole ratio due to reducing of the electron affinity difference between CdZnS and CdTe films. However, the increase of series resistance due to the high resistivity of Cd1-xZnxS films results in reducing conversion efficiency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.133-138
• /
• 2017

We evaluated the structural, electrical and optical properties of tungsten (W)-doped $Ge_8Sb_2Te_{11}$ thin films. In a previous work, GeSbTe alloys were doped with different materials in an attempt to improve thermal stability. 200 mm thick $Ge_8Sb_2Te_{11}$ and W-doped $Ge_8Sb_2Te_{11}$ films were deposited on p-type Si (100) and glass substrates using a magnetron co-sputtering system at room temperature. The fabricated films were annealed in a furnace in the $0{\sim}400^{\circ}C$ temperature range. The structural properties were analyzed using X-ray diffraction (X'pert PRO, Phillips). The results showed increased crystallization temperature ($T_c$) leading to thermal stability in the amorphous state. The optical properties were analyzed using an UV-Vis-IR spectrophotometer (Shimadzu, U-3501, range : 300~3,000 nm). The results showed an increase in the crystalline material optical energy band gap ($E_{op}$) and an increase in the $E_{op}$ difference (${\Delta}E_{op}$). This is a good effect to reduce memory device noise. The electrical properties were analyzed using a 4-point probe (CNT-series). This showed increased sheet resistance ($R_s$), which reduces programming current in the memory device.

• Journal of Fashion Business
• /
• v.11 no.1
• /
• pp.136-148
• /
• 2007

African marigold is a common plant easily available in many flower beds. It has been reported as a practical and prospective resource of dyes since the dyes can be extracted from their bodies as well as petals. In this research, cotton and ramie fabrics which are made from natural cellulose were dyed using the extract of the African Marigold which is a variety of marigold. Dyeing tests were carried out under different pH of the dye solution and mordants. Dyeability was evaluated by examining and measuring surface color, K/S value, and the changes in the maximum absorption wavelength. The probability of improving dyeability was investigated by pre-mordanting with pre-treated chitosan. For the dyeing with marigold extract, the color tone did not differ by pre-mordanting and non-mordanting. Reaction with post-mordanting was excellent, which was colored in various yellow series. The best dyeability was achieved in dye solution of pH 6.5-7.0 which is not conditioned. The largest K/S value and color difference were obtained in tin mordanting. The dye uptake was greatly increased in chitosan pre-treated mordanting compared with the post-mordanting without chitosan pre-treatment. Due to its high heat resistance, African Marigold extract is easy for dye extraction and dyeing, and its dyeability is excellent for natural cellulose fibers. Also, colorfastness was proved to be practically usable.

• Steel and Composite Structures
• /
• v.29 no.1
• /
• pp.1-22
• /
• 2018

Multi-storey precast concrete skeletal structures are assembled from individual prefabricated components which are erected on-site using various types of connections. In the current design of these structures, beam-to-column connections are assumed to be pin jointed. Welded plate beam to-column connections have been used in the precast concrete industry for many years. They have many advantages over other jointing methods in component production, quality control, transportation and assembly. However, there is at present limited information concerning their detailed structural behaviour under bending and shear loadings. The experimental work has involved the determination of moment-rotation relationships for semi-rigid precast concrete connections in full scale connection tests. The study reported in this paper was undertaken to clarify the behaviour of such connections under symmetrical vertical loadings. A series of full-scale tests was performed on sample column for which the column geometry and weld arrangements conformed with successful commercial practice. Proprietary hollow core slabs were tied to the beams by tensile reinforcing bars, which also provide the in-plane continuity across the connections. The strength of the connections in the double sided tests was at least 0.84 times the predicted moment of resistance of the composite beam and slab. The secant stiffness of the connections ranged from 0.7 to 3.9 times the flexural stiffness of the attached beam. When the connections were tested without the floor slabs and tie steel, the reduced strength and stiffness were approximately a third and half respectively. This remarkable contribution of the floor strength and stiffness to the flexural capacity of the joint is currently neglected in the design process for precast concrete frames. In general, the double sided connections were found to be more suited to a semi-rigid design approach than the single sided ones. The behaviour of double sided welded plate connection test results are presented in this paper. The behaviour of single sided welded plate connection test results is the subject of another paper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.2314-2320
• /
• 2015

MBR (Membrane Bio-Reactor) process is known to consume enormous energy to control membrane fouling. To solve this problem, electro-coagulation technique has been applied to MBR. A series of electro-coagulation was applied to activated sludge suspension under different current density condition. After the electro-coagulations, membrane filtration of the activated sludge suspensions was conducted to investigate the effect of electro-coagulation on the fouling. As current density increased 10 to 40A/m2, the total fouling resistance (Rc+Rf) decreased from 18 to 79%, showing that the electro-coagulation improved the membrane filtration efficiency. Both the organic concentration in bulk and the particles size distribution were not nearly changed before and after the electro-coagulation. The enhanced filtration efficiency might be due to the aluminum hydroxide generated from chemical precipitation, which can be acted as a dynamic membrane preventing a deposition of foulants on membrane surfaces.

• Microbiology and Biotechnology Letters
• /
• v.15 no.5
• /
• pp.319-327
• /
• 1987

In order to develop useful plasmid vectors for Zymomonas cells, attempts were made to isolate natural plasmids from Z. mobilis ATCC10988. Among a few plasmids isolated, a small plasmid of 3.9 Kb size was chosen and designated as pZM3. By introducing the replication origin of pZM3 into pBR325, a hybrid plasmid vector of 8.4 Kb size, pHZ22, was constructed. This vector contained chloramphenicol resistant gene as a selectable marker and proved to be conjugally transmissible and stably maintained in Z. mobilis. Tetracycline resistant gene was isolated from RP4 and introduced into pHZ22 to make a new vector called pHZT224 of 10.7 Kb size. Through n series of experiments, it was evident that these plasmid vectors containing selectable markers of chloramphenicol and tetracycline resistance were shuttle vectors functional in Z. mobilis as well as E. coli.

• The Korean Journal of Physiology and Pharmacology
• /
• v.4 no.3
• /
• pp.169-175
• /
• 2000

To learn the developmental changes in intrinsic electrophysiological properties of the second order taste neurons, whole cell recordings from the developing nucleus of the solitary tract neurons were done in brainstem slices of postnatal rats. Rats aged from postnatal 0 to 21 days (P0-P21) were used, being divided into 3 age groups: postnatal first week (P0-P7 days), second week (P8-P14 days), and third week (P15-P21 days). Slices containing gustatory NTS were cut horizontally in the thickness of $300\;{\mu}m.$ Whole cell recordings were obtained from neurons in response to a series of hyperpolarizing and depolarizing current pulses. The intrinsic electrophysiological properties of the rostral NTS (rNTS) neurons were compared among the age groups. Depolarizing current pulses evoked a train of action potentials in all neurons of all age groups. The resting membrane potential and input resistance of the neurons did not show any significant differences during the postnatal 3 weeks. The time constant, however, decreased during the development. Duration of action potential measured at half maximum amplitude was longer in younger age groups. Both the maximum rate of rise and the maximum rate of fall in the action potential increased during the first 3 weeks postnatal. Electrophysiologically more than half neurons were type III. In summary, it is suggested that developmental changes in electrophysiological properties in rNTS occur during the first three weeks in rats.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.3
• /
• pp.269-275
• /
• 2005

A flux lock-type SFCL consists of two coils which are wound in parallel each other through an iron core, and a HTSC thin film connects in series with coil 2. The operation of the flux-lock type SFCL can be divided into the subtractive polarity winding and the additive polarity winding operations according to the winding directions between coil 1, coil 2. When a fault occurs, the fault current in the HTS thin film exceeds the critical current so that resistance is generated in the HTS film, and thereby the fault current is limited by an instant rise in the impedance of the flux-lock type SFCL. We investigated he variances of initial fault current limiting instant according to the ratio of inductance of coil 1 and coil 2 in the flux-lock type SFCL. It was confirmed from experiments that the initial fault current limiting instant in the subtractive polarity and additive polarity windings were faster as the ratio of coil 2' inductance for coil 1's inductance increased. The 1st peak of fault current in case of the subtractive polarity winding was higher as the ratio of coil 2's inductance for coil 1's inductance increased. On the other hand, in case of the additive polarity winding, the 1st peak of fault current was lower.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.2
• /
• pp.57-65
• /
• 2010

To determine the static buckling loads and evaluate the structural performance of slender steel pipe-arches such as for greenhouse structures, a series of modal tests using a fixed hammer and roving sensors was carried out, by providing no load, then a range of vertical loads, on an arch rib in several steps. More attention was given to an internal arch where vertical and horizontal auxiliary members are not placed, unlike an end arch. Modal parameters such as natural frequencies, mode shapes and damping ratios were extracted using more advanced system identification methods such as PolyMAX (Polyreference Least-Squares Complex Frequency Domain), and compared with those predicted by commercial FEA (Finite Element Analysis) software ANSYS for various conditions. A good correlation between them was achieved in an overall sense, however the reduction of natural frequencies due to the existence of preaxial loads was not apparent when the vertical load level was about up to 38% of its resistance. Some difficulties related to the field testing and parameter extraction for a very slender arch, as might arise from the influences of neighboring members, are carefully discussed.