• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.643-646
• /
• 2003

This study concerns the new estimated strength equation of concrete by penetration test. There are not only few estimate strength equations of concrete, but also many problems to apply them because of time, cost, easiness, structural damage, reliability and so on. In this study, there performed a series of test for one year and estimated strength equation of concrete as follows; Linear: fck =3.38d - 95.1 ($$r^2$$=88.6%) Quadratic: fck =0.188$$d^2$$- 10.76d + 166.3 ($$r^2$$=96.7%) here, fck : estimated compressive strength of concrete by Mpa d: exposed probe length by mm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.57-63
• /
• 2015

Fault currents characteristics contain decaying DC offset. First cycle peak value of fault currents is higher than steady-state fault current value. These characteristics can affect the operation of protective device. To reduce the asymmetric fault current, the method using a series connection of two hybrid-type Superconducting Fault Current Limiter(SFCL) components, an auxiliary SFCL and a main SFCL, has been proposed. The auxiliary SFCL limits the first half cycle fault current, while main SFCL limits the steady state fault currents. This paper proposed a decision method of the optimal insertion resistance of auxiliary and main SFCL components. To verify the effectiveness of proposed scheme, the various simulations are performed by using Electromagnetic Transient Program(EMTP).

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.117-122
• /
• 2000

In these days, the pollution of marine environment near island at Korean coastal zone caused by the trash, human waste and livestocks excreta become series problem. One of the most economic and efficient way to prevent this pollution problem is to set up island circulating incineration system. In this paper, the results of feasibility study on the application of turtle boat hull form to the incinearting vessel has been summarized especially for the resistance and course keeping point of view.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.671-674
• /
• 2003

본 논문에서는 Cobalt interlayer 와 Titanium Nitride(TiN) capping layer를 Ni SALICIDE의 단점인 열 안정성과 sheet resistance 와 series 저항을 감소시키는데 적용하여 0.lum 급 CMOS 소자의 특성을 연구하였다. 첫째로, Ni/Si 의 interface 에 Co interlayer 를 증착하여 Nickel Silicide의 단점인 열 안정성 평가인 700℃, 30min의 furnace annealing 후에 낮은 sheet resistance와 누설전류를 줄일 수 있었다. 두번째로, TiN caping layer를 적용하여 실리사이드 형성시 산소와의 반응을 막아 실리사이드의 표면특성을 향상시켜 누설전류의 특성을 개선하였다. 결과적으로 소자의 구동전류 향상, 누설전류 저하, 낮은 면저항으로 소자의 특성을 개선하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.197-204
• /
• 2002

DRAM, SRAM, and FLASH memory are three major memory devices currently used in most electronic applications. But, they have very distinct attributes, therefore, each memory could be used only for limited applications. MRAM (Magneto-resistive Random Access Memory) is a promising candidate for a universal memory that meets all application needs with non-volatile, fast operational speed, and low power consumption. The simplest architecture of MRAM cell is a series of MTJ (Magnetic Tunnel Junction) as a data storage part and MOS transistor as a data selection part. To be a commercially competitive memory device, scalability is an important factor as well. This paper is testing the actual electrical parameters and the scaling factors to limit MRAM technology in the semiconductor based memory device by an actual integration of MRAM core cell. Electrical tuning of MOS/MTJ, and control of resistance are important factors for data sensing, and control of magnetic switching for data writing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.71-74
• /
• 2003

In this paper, electrical properties of photovoltaic module have been observed for 5 years and found to drop around 5 to 25 %. Element technologies which are critical to electrical loss were therefore examined and dark I-V curve were observed with different soldering conditions. From the results, series resistance decreased with the decrease of contact resistance regardless of temperature conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.216-220
• /
• 1994

Polycrystalline CdS films have been prepared by coating a slurry, which consisted of CdS, 11w% CdCl$_2$ and appropriate amount of propylene glycol, on glass substrate and glass substrate coated with indium tin oxide(ITO) followed by sintering in a nitrogen atmosphere. CdTe slurries consisting of Te powder and Cd powder were coated on the sintered CdS films and ITO/CdS films and were sintered in nitrogen to prepare sintered CdS/CdTe and ITO/CdS/CdTe solar cells. The value of fill factor increased due to low series resistance and open circuit voltage decreased due to low shunt resistance in the ITO/CdS/CdTe solar cells.

• Proceedings of the KWS Conference
• /
• 1999.05a
• /
• pp.215-218
• /
• 1999

With increasing demand of energy saving, -many efforts were made to employ aluminium alloys in the automobile industry. Especially, resistance spot welding has been widely used in the steel metal joining process because of its high productively and convenience. In this paper, spot weldability of 7075-T6 aluminium thin sheets for various welding conditions were examined by series of experiments. The tensile shear strength and microstructure of welded specimens was observed, and The optimal welding conditions were found for each welding conditions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.320-325
• /
• 2009

The constrained modulus, representative property to evaluate compressibility of soil, is needed to estimate the settlement of ground structure. A series of lab and field cone penetration tests for clayey soil of Busan new-port and Noksan industrial area were conducted to evaluate the estimation method of constrained modulus. Since CPT generates large deformation of ground, it is difficult to correlate the cone resistance with the constrained modulus. Therefore, appropriate correlation between them is essential to estimate the constrained modulus based on CPT results. The test results show that the ratio of the constrained modulus to the cone resistance is inversely proportional with plasticity index. Based on this result, the estimation method of constrained modulus for Busan clay is suggested.

• Proceedings of the Safety Management and Science Conference
• /
• 2002.11a
• /
• pp.273-277
• /
• 2002

In the electrode fabrication of unit cell, we found that optimal the electrochemical characteristics were obtained with at 90 wt.% of activated carbon(BP-20), 5 wt.% of conducting agent(Ppy, Super P) and 5 wt.% of P(VdF-co-HFP)/PVP mixed binder. The electrochemical characteristics of unit cell with Ppy improver were as follows : 37.6 F/g of specific capacitance, 0.98 $\Omega$ of AC-ESR, 2.92 Wh/kg and 6.05 Wh/L of energy density, and 754 W/kg and 1,562 W/L of power density. It was confirmed that internal resistance were reduced due to the increase of electrical conductivity and filling density by the introduction of conductivity agent, and content of conducting agent was suitable in the range of 4~6 wt.%. According to the impedance measurement of the electrode with conductivity agent, we found that it was possible to charge rapidly by the fast steady-state current convergence due to low equivalent series resistance(AC-ESR), fast charge transfer rate at interface between electrode and electrolyte, and low RC time constant.