• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.409-412
• /
• 2006

In process of reinforced concrete(RC) box structure, the heat of hydration may cause serious thermal cracking problems. In order to eliminate hydration heat of mass concrete, this paper reports results of hydration heat control in mass concrete using the OCHP(Oscillating Capillary tube Heat Pipe). Recently OCHP is drawn special attention from these points of low cost as well as short construction schedule for the manufacturing of heat exchanger, flexibility, simplification and high performance. There were three RC box molds$(1.2{\times}1.2{\times}1.2m)$ which shows a difference as compared with each other. One was not equipped with OCHP. While others were equipped with OCHP and these were cooled with air natural convection and spraying water respectively. The OCHP was composed of copper pipe with 12 turns(O.D : 4mm, I.D : 2.8mm). The working fluid was R-22 and its charging ratio was 30(Vol. %). In order to analyze the distribution of temperature and index figure of thermal crack in sequential placement of mass concrete, we used HYCON of computer program. As a result of the experiment, the peak temperature decreased about $15.6\sim23.4^{\circ}C$ than the general specimen and the probability of thermal crack generated in mass concrete decreased up to 0%.

• 한국전기화학회:학술대회논문집
• /
• 1998.12a
• /
• pp.7-27
• /
• 1998

In order to design capacity of lithium ion battery, some calculations were carried out based on the characteristics of materials by the given battery shape and dimension. The principle of design was built by the interpretation of the correlation of material, electrochemical and battery factors. Parameters of materials are fundamental physical properties of constituent such as cathode. separator, anode, current collectors and electrolyte. Electrochemical factor includes potential pattern as a function of specific capacity, specific discharge capacity(or initial irreversible specific capacity or Ah efficiency) as a function of specific charge capacity and material balancing. Parameters of battery are dimension, construction hardware and performance. Battery capacity was simulated for a lithium cobalt dioxide as cathode and a hard carbon as anode to achieve 1100 mAh for the charge limit voltage of 4.2V, the weight ratio(+/-) of 2.4 and ICR18650. A fabricated test cell (ICR18650) which have weight ratio(+/-) of 2.4 discharged to 1093 mAh for the charge limit voltage of 4.2V. The sequential discharge capacity show good correspondence with designed capacity.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.3
• /
• pp.13-21
• /
• 2007

A forklift is a motive machine powered by LPG, diesel engine or electric motors. The internal combustion engine type forklift is equipped with automatic transmission to meet the required drive load as well as the easy operation of the vehicle. This paper deals with the shift control and endurance test controller which is developed for the functional test of the newly designed automatic transmission on a dynamometer test bench. Its major function is to control the proportional solenoid currents, which is directly related to clutch pressures, for the given reference current trajectory during shift and sequential operation of shift schedule designed for the durability test at each gear. It also has the ability to monitor all the necessary test data through RS232 communication and log them to disk files. The current controller of embedded system is designed from the identified dynamics of solenoid coil and the current reference can be easily modified with a user interface software on PC so as to match the shift data by experiments.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.3
• /
• pp.63-69
• /
• 2009

The undisturbed specimens used in this research were sampled in the field by the sequential sampling method. In addition, four testing methods were applied to identify for the characteristics and classification of weathered strata. N-value by standard penetration test was obtained from in the field and then analyzed using normalization method. Other methods such as X-ray grain size distribution, X-ray fluorescence spectroscopy(XRF), and fall cone test were carried out in the lab. These analyzed results indicate that distribution of particle, composition of minerals are changed in accordance with the degree of weathering, unusual strata and depth. Consequently, the weathered strata can be extensively separated into two parts according to the test results and each part was shown different in the strata characteristics. It can be prospected that mechanical characteristics should be different, even though mechanical tests were not applied. Furthermore, these results not only make up for the error by one testing method but also contribute more effectively and economically to the design and the construction.

• Speech Sciences
• /
• v.10 no.4
• /
• pp.7-21
• /
• 2003

Sums-of-Products models were built for segment duration prediction of spoken Korean. An experiment for the modelling was carried out to apply the results to Korean text-to-speech synthesis systems. 670 read sentences were analyzed. trained and tested for the construction of the duration models. Traditional sequential rule systems were extended to simple additive, multiplicative and additive-multiplicative models based on Sums-of-Products modelling. The parameters used in the modelling include the properties of the target segment and its neighbors and the target segment's position in the prosodic structure. Two optimisation strategies were used: the downhill simplex method and the simulated annealing method. The performance of the models was measured by the correlation coefficient and the root mean squared prediction error (RMSE) between actual and predicted duration in the test data. The best performance was obtained when the data was trained and tested by ' additive-multiplicative models. ' The correlation for the vowel duration prediction was 0.69 and the RMSE. 31.80 ms. while the correlation for the consonant duration prediction was 0.54 and the RMSE. 29.02 ms. The results were not good enough to be applied to the real-time text-to-speech systems. Further investigation of feature interactions is required for the better performance of the Sums-of-Products models.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.9 s.252
• /
• pp.1062-1069
• /
• 2006

Reduction schemes approximate the lower eigenvalues that represent the global behavior of the structures. But, they are not efficient to be applied to large-scaled problems because these schemes require considerable amount of computing time in constructing reduced one from the original large-scaled systems. In addition, the selection of the primary degrees of freedom might be localized to cause the excessive emphasis of the lower mode or lost of the important modes. In the present study, a new reduction method combined with the subdomain method is proposed. For the construction of the final reduced system the system of each domain subdivided into primary, slave and interface degrees of freedom. It is remarkably efficient and accurate comparable to full-scale system. Numerical examples demonstrate that the proposed method saves computational cost effectively and provides a reduced system which predicts accurate eigen-pairs of global system.

• Journal of Korean Society for Quality Management
• /
• v.47 no.3
• /
• pp.523-535
• /
• 2019

Purpose: We research on the efficient response surface methodology(RSM) design to develop a design space in Quality by Design(QbD). We propose practical designs for the successful construction of the design space in QbD by allowing different number of replicates at the box points, star points, and the center point in the rotatable central composite design(CCD). Methods: The fraction of design space(FDS) plot is used to compare designs efficiency. The FDS plot shows the fraction of the design space over which the relative standard error of predicted mean response lies below a given value. We search for practical designs whose minimal half-width of the tolerance interval per a standard deviation is less than 4.5 at 0.8 fraction of the design space. Results: The practical designs for the number of factors between two and five are listed. One of the designs in the list could be chosen depending on the experimental budget restriction. Conclusion: The designs with box points replications are more efficient than those with the star points replication. The sequential method to establish a design space is illustrated with the simulated data based on the two examples in RSM.

• Journal of Drive and Control
• /
• v.19 no.1
• /
• pp.26-33
• /
• 2022

This study dealt with a self-propelled spinach harvester, which is capable of carrying out sequential harvesting work. This study aimed to find the cause of the harvester's occasional performance deterioration, which occurs in the process of simplifying the hydraulic circuit, using a multi-domain analysis model. The study was carried out in the following manner. First, a hydraulic system analysis model, which combines linear motion, rotary motion, hydrodynamic behavior, and an electrical signal, was developed through SimulationX software, specialized in multi-domain analysis. Second, a scenario for single behavior and coupled behavior was set out on an actuator basis. Third, the flow rate of the hydraulic system, which is not required for the movement of the actuator, was quantitatively analyzed. The results showed that a change in oil temperature was the cause of the harvester's occasional performance deterioration. And the higher the oil temperature, the more serious the performance deterioration, especially as the number of actuators operated simultaneously was small.

• Journal of Drive and Control
• /
• v.19 no.1
• /
• pp.69-75
• /
• 2022

This study aimed to develop solutions for the intermittent performance deterioration of self-propelled spinach harvesters through analysis model. The study was conducted in the following manner. First, changes in performance deterioration and surplus flow, which result from oil temperature changes, were analyzed by simulating actual sequential harvesting movements, which involve driving with actuators operated simultaneously, by analysis model developed in a previous study. Second, fundamental solutions for surplus flow problems were presented. Third, the solutions were applied to a virtual environment to present their practicality and quantitative effects. The two solutions based on the study results were as follows. First, a closed center-type directional control valve was applied to the hydraulic circuit. Second, an unloading system was set up through an on-off solenoid valve.

• Geomechanics and Engineering
• /
• v.34 no.1
• /
• pp.29-41
• /
• 2023

The 3D geospatial modeling of geotechnical information can aid in understanding the geotechnical characteristic values of the continuous subsurface at construction sites. In this study, a geostatistical optimization model for the three-dimensional (3D) mapping of subsurface stratification and the SPT-N value based on a trial-and-error rule was developed and applied to a dam emergency spillway site in South Korea. Geospatial database development for a geotechnical investigation, reconstitution of the target grid volume, and detection of outliers in the borehole dataset were implemented prior to the 3D modeling. For the site-specific subsurface stratification of the engineering geo-layer, we developed an integration method for the borehole and geophysical survey datasets based on the geostatistical optimization procedure of ordinary kriging and sequential Gaussian simulation (SGS) by comparing their cross-validation-based prediction residuals. We also developed an optimization technique based on SGS for estimating the 3D geometry of the SPT-N value. This method involves quantitatively testing the reliability of SGS and selecting the realizations with a high estimation accuracy. Boring tests were performed for validation, and the proposed method yielded more accurate prediction results and reproduced the spatial distribution of geotechnical information more effectively than the conventional geostatistical approach.