• KSBB Journal
• /
• 제11권1호
• /
• pp.46-51
• /
• 1996

연속식 포말 분리관에 효모 용액을 일정하게 공급 하여 분리 실험을 수행하며 배지 공급량, 질소 공급량, 온도와 pH, 배지의 희석비 및 $CaCl_2$첨가 등의 영향에 따른 연속 포말 분리관의 분리 및 특성 등을 연구하였다. 배지 공급량이 200ml/hr인 경우 액본 체 효모의 90-95%가 제거되어 매우 효과적인 분 리법이었다. 질소 공급량이 50ml/min일때 효모 제 거율은 90-95%의 높은 수치를 나타내었다. 효모 용액 줌의 효모 농도가 1.18g/$\ell$ 일 때 액본체 효모 가 90% 가까이 제거되었고 효모 분리비도 145로 매우 효과적인 분리의 특성을 나타내었다. 효모 용 액의 pH가 4.6-5.6일때 최대의 효모 분리비 78.4~83.6 로 나타났고, 효모 용액의 온도가 $32^{\circ}C$일때 효모 분리비는 80.5, 효모 제거율은 87.3의 값을 나 타내었고, 효모 용액 중의 $CaCl_2$.의 농도가 0.5g/$\ell$ 일 때 효모 분리비는 90.04, 효모 제거율은 83.3% 로 높은 수치를 나타내였다. 배지의 희석비가 3배일 때 효모 분리비가 122.2로 높은 수치를 나타내였고 액본체 내의 효모도 92.8%가 제거되는 효과적인 분 리 특성을 나타내어 포말분리법은 용액 중 효모를 분리하기 위한 매우 효과척인 방법이었다.

• 대한환경공학회지
• /
• 제36권2호
• /
• pp.147-152
• /
• 2014

본 연구에서는 폴리설폰 중공사막을 이용하여 화석연료 연소에서 배출되는 온실가스 중 $CO_2$의 회수에 관한 연구를 실시하였다. 고농도의 $CO_2$를 회수하기 위한 막분리 공정에 대한 선행연구이다. 혼합가스 분리거동 관찰을 위하여 이산화탄소가 10% 함유된 배기가스를 사용하였다. 압력, 온도, 주입가스 조성, 다단 막 변화를 주어 스테이지 컷에 따른 분리 성능을 조사하였다. 압력과 온도가 증가 할수록 투과측에 $CO_2$ 농도와 회수율이 증가하였다. 주입 가스 조성 변화 시 $CO_2$의 함량이 높을 경우 회수율 및 분리 효율이 높아졌다. 3단 분리막 시스템을 이용시 $CO_2$ 농도 95% 이상, 회수율 90% 이상 보였으며 1단 분리막 보다 분리율이 향상되었다.

• 멤브레인
• /
• 제33권6호
• /
• pp.369-376
• /
• 2023

본 연구에서는 에너지 소모가 큰 기존 진공 증류 공정의 대안으로 친환경이면서 에너지 효율적인 투과증발 분리공정을 이용하여 1,2 hexane diol/water (1,2 HDO/water) 혼합물에서 물을 분리하는 데 적용되었다. 사용한 분리막은 glutaraldehyde (GA)로 가교된 PVA를 알루미나 중공사 막(Al-HF) 내부에 코팅하여 사용하였다. 1,2 HDO/water 투과증발 분리공정에서는 PVA/GA 비율, 경화 온도 및 투과증발 분리공정 운전 조건에 대한 막의 최적화를 연구하였다. 장기 안정성 시험에서 PVA/GA (몰 비율 = 0.08, 경화 온도 = 80℃) 로 코팅된 Al-HF 막이 공정온도 40℃에서 1.90~2.16 kg/m²h 범위의 투과도를 보였으며, 투과용액의 수분 함량은 99.5% (separation factor = 68) 이상이었다.

• 대한기계학회논문집B
• /
• 제22권9호
• /
• pp.1255-1266
• /
• 1998

Effects of a length-to-diameter ratio, L/D, on the three-dimensional flow and aerodynamic loss within an injection hole, which is normally oriented to the mainflow, have been investigated by using a straight five-hole probe. The length-to-diameter ratio of the injection hole is varied to be 0.5 and 2.0 for blowing ratios of 0.5, 1.0 and 2.0. Regardless of the blowing ratio, flows within the hole and at the jet exit are strongly affected by the length-to-diameter ratio. In the case of L/D=0.5, the inside flow is considerably influenced by the mainflow, and the exit flow variation is found to be the greatest. The aerodynamic loss in this case is usually attributed to jet -mainflow interactions. In the case of L/D=2.0, the flow separation and reattachment in the inlet region are completely separated from the complicated exit flow, and the aerodynamic-loss production is mainly due to the inlet flow separation.

• 설비공학논문집
• /
• 제14권9호
• /
• pp.741-748
• /
• 2002

The present study investigated the two-phase flow characteristics of refrigerant R-22 in T-branch with horizontal and vertical inlet tube The key experimental parameters were the orientation of inlet and branch tubes (horizontal and vertical), diameter ratio of branch tube to inlet tube (1 and 0.61), inlet mass flux (200~500 kg/$m^2$s) and inlet quality (0.1~0.4). Predicted pressure profile agreed with the measured data within 25.4%. The flow distribution ratio decreased as the mass flux increased. The flow distribution ratio decreased by 12~25% as the tube diameter ratio decreased from 1 to 0.61, and decreased by 38~47% as the orientation of branch changed from horizontal to vertical upward for horizontal inlet tubes. As the orientation of inlet tube changed from horizontal to vertical upward for horizontal branch, the flow distribution ratio increased by 15~68%, but the quality in the branch tube decreased by 28~92% due to phase separation.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.143-149
• /
• 2008

A numerical study was performed for a vane of a compressor with a high-turning angle and meridional divergence. At first, the effect of the suction position was discussed. Then, the optimal suction position was applied to the cascades with the aspect ratio of 2.53 and 0.3, respectively, to get the knowledge of the effect of the endwall boundary layer removal on the secondary flow along the blade height. At last, using the critical principles of the three-dimensional separation, the topological structures of the flow patterns of the body surfaces and the separation configurations were discussed in detail. The results show that the largest reduction of the total loss can be achieved when the suction slot is near the suction side. The topological structure as well as the separation configuration varies due to boundary layer removal, which restrains the flow separation at the corner and delays or depresses the separation on the suction surface. Compared with the original cascade, the cascade with the endwall boundary layer removal has a higher blade loading along the most span. Furthermore the flow loss decreases and distributes uniformly along the span.

• Nuclear Engineering and Technology
• /
• 제55권4호
• /
• pp.1225-1232
• /
• 2023

The ¹⁸⁰W is the lightest isotope of Tungsten with small abundance ratio. It is slightly radioactive (α decay), with an extremely long half-life. Its separation is possible by non-conventional single withdrawal cascades. The ¹⁸⁰W is used in radioisotopes production and study of metals through gamma-ray spectroscopy. In this paper, single withdrawal cascade model is developed to evaluate multicomponent separation in non-conventional transient cascades, and available experimental results are used for validation. Numerical studies for separation of ¹⁸⁰W in a transient single withdrawal cascade are performed. Parameters affecting the separation and equilibrium time of cascade such as number of stages, cascade arrangements, feed location and flow rate for a fixed number of gas centrifuges (GC) are investigated. The Salp Swarm Algorithm (SSA) as a bio-inspired optimization algorithm is applied as a novel method to minimize the feed consumption to obtain desired concentration in the collection tank. Examining different cascade arrangements, it is observed in arrangements with more stages, the separation is further efficient. Based on the obtained results, with increasing feed flow rate, for fixed product concentration, the cascade equilibrium time decreases. Also, it is shown while the feed location is the farthest stage from the collection tank, the separation and cascade equilibrium time are well-organized. Finally, using SSA optimal parameters of the cascade is calculated, and optimal arrangement to produce 5 gr of ¹⁸⁰W with 90% concentration in the tank, is proposed.

• 오토저널
• /
• 제7권4호
• /
• pp.49-56
• /
• 1985

This study consists of instrumenting and running tests on variable compression engines and measuring the following combustion characterics: (a)flame speed, (b) emission and (c)performance parameter such as power and economy. The results were as follows: 1) The phase separation diagram of substitute fuels were obtained from phase separation experiment. 2) The flame propagation speed of substitute fuels were higher than gasoline and increased with increasing methanol weight percent of substitute fuels. 3) BEMP of substitute fuels was slightly less than that of gasoline but in the range of small weight percent, BEMP was compatible to gasoline. 4) Concentration of NOx decreased significantly with delaying spark advancing time. Also, it decreased for rich equivalence ratio but increased with high compression ratio. In general, NOx concentration was much lower than that of gasoline. 5) Concentration of HC and CO increased for rich equivalence ratio. Also it was lower than that of gasoline.

• 에너지공학
• /
• 제7권2호
• /
• pp.180-186
• /
• 1998

본 연구에서는 벤토나이트 혼합액의 유동특성 등을 파악하기 위형 전단속도에 따른 점도의 변화를 측정하였으며, 박막형성에 관한 특성을 파악하기 위하여 혼합비 및 점도에 따른 박막두께를 측정하였다. 또한 건조 후 박막이 박막의 두께에 따른 오염표면에서 분리되는 특성을 조사하였으며 벤토나이트의 흡착성능에 영향을 미치는 비표면적을 측정하기 위하여 BET 방법을 이용하였다. 점도는 혼합비의 증가에 따라 감소하였으며 건조박막의 두께는 혼합비가 증가할수록 두꺼워진다. 건조박막의 분리특성은 혼합비가 5에서 10% 이내로 박막이 40에서 150$\mu\textrm{m}$가 적당하다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.252-257
• /
• 2005

Injection molding is a very important industrial process for the manufacturing of plastics objects. During an injection molding process of composites, the fiber-matrix separation and fiber orientation are caused by the flow of molten polymer/fiber mixture. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation' orientation and injection molding conditions. So far, there is no research on the measurement of fiber orientation using image processing. In this study, the effects of fiber content ratio and molding condition on the fiber orientation-angle distributions are studied experimentally. Using the image processing method, the fiber orientation distribution of weld-line in injection-molded products is assessed. And the effects of fiber content and injection mold-gate conditions on the fiber orientation are also discussed.