• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.929-930
• /
• 2012

• Wind and Structures
• /
• 제9권2호
• /
• pp.109-124
• /
• 2006

This paper describes the characteristics of the fluctuating lift forces when a circular cylinder vibrates in the cross-flow direction. The response characteristics on elastically supported the circular cylinder was first examined by a free-vibration test. Next, flow-induced vibrations obtained by the free-vibration test were reproduced by a forced-vibration test, and then the characteristics of the fluctuating lift forces, the work done by the fluctuating lift, the behavior of the rolling-up of the separated shear layers were investigated on the basis of the visualized flow patterns. The main findings were that (i) the fluctuating lift forces become considerably large than those of a stationary circular cylinder, (ii) negative pressure generates on the surface of the circular cylinder when the rolling-up of separated shear layer begins, (iii) the phase between the fluctuating lift force and the cylinder displacement changes abruptly as the reduced velocity $U_r$ increases, and (iv) whether the generating cross-flow vibration becomes divergent or convergent can be described based on the work done by the fluctuating lift force. Furthermore, it was found that the generation of cross-flow vibration can be perfectly suppressed when the small tripping rods are installed on the surface of the circular cylinder.

• 한국전산유체공학회지
• /
• 제4권3호
• /
• pp.44-51
• /
• 1999

A modified version of SST turbulence model is suggested to simulate unsteady separated flows over oscillating airfoils. The original SST model, which shows good performance in predicting various steady flows, often results in oscillatory behavior of aerodynamic loads in large separated flow regions. It is shown that this oscillatory behavior is due to the adoption of the absolute value of vorticity in generalizing the original model. As a remedy, a modification is made such that the vorticity in the original SST model is replaced by strain rate. The present model is verified for a mild separated airfoil flow at fixed angle of incidence and for unsteady flowfields about oscillating airfoils. The results are compared with BSL model and original SST model. It is illustrated that the present model gives a better agreement with the experimental results than other two models.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.67-72
• /
• 2003

Numerical calculation has been performed to investigate the effect of inlet configuration on the growth rate of GaN layer on the heated susceptor. The conventional single inlet, where the gas is mixed by force in the inlet, is compared with separated flow inlet. Two-parallel gas flow $H_{2}$ and $NH_{3}$ are separated by a plate with finite length which are also parallel to the susceptor. The effect of separated plate length, carrier gas and flow rate of each precursor on the mixing of reactant gases and growth rate were investigated. Furthermore the three dimensional model is employed to predict the transverse variation of growth rate.

• 대한기계학회논문집
• /
• 제19권11호
• /
• pp.3014-3021
• /
• 1995

This study is carried out in order to evaluate the performances of the Reynolds stress turbulence models such as SSG and GL models in the calculation of separated flow over backward-facing stepp.In addition, two slow return-to-isotropy models, YA and Rotta models combined with rapid part of SSG model are also tested. The finite volume method is used to discretize the governing differential equations, and the power-law scheme is used to approximate the convection terms. The SIMPLE algorithm is used for pressure correction in the governing equations. The results show that SSG model gives the better prediction near the reattachment point than GL model. In cases that the rapid term of SSG model is combined with Rotta and YA slow models, the results show the better predictions of stress components in recirculation zone, but indicate inaccuracy in the predictions of mean velocity.

• 대한기계학회논문집
• /
• 제19권9호
• /
• pp.2328-2341
• /
• 1995

An experimental study on the flow over the axisymmetric backward-facing step was carried out. The purposes of the present study are to investigate the effect of the free stream turbulence intensity on the reattachment length and to understand the turbulence structure of the recirculating flows. Local mean and fluctuating velocity components were measured in the separated and reattaching axisymmetric turbulent boundary layer over the wall of convex cylinder placed in a water tunnel by using 2-color 4-beam fiber optics laser Doppler velocimetry. As the free stream turbulence intensity increased, the reattachment length became shorter due to the enhanced mixing in the separated shear layer. It was also observed that the reverse flow velocity and turbulent kinetic energy increase with increasing free stream turbulence intensity. Spectral data and flow visualization showed that low-frequency motions occur in the separated flow behind a backward-facing step. These motions have a significant effect on the time-averaged turbulence data.

• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1708-1715
• /
• 2003

An experimental study was made of turbulent separated and reattaching flow over a backward-facing step, where unsteady wake was generated by a spoked-wheel type wake generator with cylindrical rods in front of the separated flow. The influence of unsteady wake was scrutinized in terms of the rotating speed of the wake generator (0$\leq$S $t_{H}$$\leq$0.4). A conditional averaging technique in corporation with SBF was employed to elucidate the influence of the unsteady wake on the large-scale vortical structures of the separated flow. Special attention was made during two-dimensional measurements of wall-pressure with or without unsteady wake. The wall-pressure fluctuations were used to predict dipole sound source by Curie's integral formula. It was found that the reduction of the dipole sound source was due to the reduction of turbulent kinetic energy by unsteady wake in the recirculation region.n.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.94-99
• /
• 2008

The characteristics of the flowfield of a square prism having fences on the corner was investigated by the PIV. Strouhal numbers, velocity vectors and velocity profiles around the square prism were observed at various positions of the fences, and Reynolds number of $Re=0.6{\times}10^4{\sim}1.0{\times}10^4$. As the results in case of the prism having fences the Strouhal numbers were all smaller than in case of the prototype prism. In case of the prism having vertical fences on the front corners the concentrated intensity of the vorticity was the strongest and the size of separated shear layer was the largest. While in case of the prism having vertical fences on the rear corners the concentrated intensity of the vorticity was the weakest and the size of separated shear layer was the smallest. Also in this case, the flow separated in front corner was reattached around the rear corner and made circulation.

• 물과 미래
• /
• 제27권2호
• /
• pp.121-128
• /
• 1994

단락부에서의 모형실험을 통하여 표면 유속의 감소경향, 낙하리영역의 길이, 잠재핵(potential core)의 길이 등을 고찰하여 단구 전면에 대한 흐름을 규명하였다. 흐름속에 부류사가 혼재되어 있는 경우, 부유사가 낙하리영역 중에 퇴적하게 되어 단구의 진행 속도에 영향을 주게되므로 이를 규명하기 위하여 단락부에 있어서 부류사의 유입에 대한 실험을 실시하고, 이에 대한 식을 유도하여 실험 결과로부터 이들 식의 유효성을 증명하였다. 또한 단락부의 낙하리영역에서 사이폰에 의하여 채취되는 부류사량에 대한 실험 결과,$q_{s0}$ 를 규정하는 파라메타에 관한 검토를 실시하여 부류사의 퇴적 특성을 설명하였다.

• 한국가시화정보학회지
• /
• 제4권2호
• /
• pp.81-87
• /
• 2006

In this paper, we present flow patterns around and performance of an air-flow separator by using the numerical analysis. With this separator, particles of different density are to be separated by using the drag force from the air flow. The low-density particles are designed to be separated by using inhalation through holes on a rotating drum. To obtain the flow informations needed for determining the proper design parameters, we have performed numerical simulations by using a commercial code, ANSYS CFX. Various parameter set was tested and it was found that depending on the design of drums there exist critical parameter set regarding the attachment of light particles on the drum, which is prerequisite for the separation of materials. We present here the possibility of using the present design in separation of particles mixed in the clod for use in recycling.