• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1229-1230
• /
• 2006

This study is for implementation of PC based Motor fault diagnosis system. By using harmonics and current signals of the motor, this system diagnoses the motor condition by accumulated harmonic contribution rate. In this proposed system that was composed of 5 parts. A sensor, connection box, evaluation board, device server, and main computer are those. There were two types of sensor, one was harmonic sensor the other was current sensors. The signal was acquired by sensor, and transferred to evaluation board. Second one is connection box. Because the output type of sensor and input type of evaluation board is different, connection box was necessary. Third one was evaluation board. The signal from the sensor was converted to digital signal in evaluation board. And this signal was transferred to device server. Fourth one was device server. Device server transferred the data from evaluation board to main computer. And the last one was other parts controlled by main computer in main computer, there were communication and diagnosis algorithms. The result was derived by main computer. In the result, there were 12 categories and 5 levels of motor conditions. The proposed system had some advantages comparing with stand alone type commercial motor fault diagnosis system. The first, by using remote access it was easier to get the conditions of motor. The second, there was no need to handle the sensors when users measured the motor signals. By this property, no one was necessary at motor location site. The third, this system was less restricted by times and places than commercial stand alone type diagnosis system. Therefore users can operate this system only using the main computer. Once the sensors are installed at the motor, users doesn't need to move to check up the condition of motors. Moreover, if there is ethernet hub, many motors can be not only diagnosed at once but also decreased its cost.

• 한국광학회지
• /
• 제15권5호
• /
• pp.415-422
• /
• 2004

교량과 각종 건물을 비롯한 대형 토목 구조물에서 발생하는 수 mm의 변위를 한 개의 광섬유로 간편하게 측정하기 위하여 광커넥터에서 반사가 굽힘 손실에 의하여 변하는 현상을 이용한 새로운 다중화된 광섬유 변위센서를 제안하고 실험하였다. 한 쌍의 광커넥터 양끝에서 반사광의 신호차이가 두 광커넥터 사이에서 발생한 굽힘 변위에 의해서 달라지는 것을 Optical Time Domain Reflectometer로 측정하여 선형으로 그 변화가 측정되는 변위센서를 만들고, 이 센서 4개를 직렬형으로 배열하여 여러 지점의 변위를 동사에 측정이 가능한 다중화 센서 시스템을 구성하고 실험하였다. 그 결과 이 변위센서를 이용하면 4개 지점에서 각각 최대 6 mm까지의 변위를 6%의 오차범위 내에서 0.9942의 선형성을 가지고 변위를 측정할 수 있음을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1689-1690
• /
• 2006

This study is for implementation of PC based Motor fault diagnosis system. By using harmonics and current signals of the motor, this system diagnoses the motor condition by accumulated harmonic contribution rate. In this proposed system that was composed of 5 parts. A sensor, connection box, evaluation board, device server, and main computer are those. There were two types of sensor, one was harmonic sensor the other was current sensors. The signal was acquired by sensor, and transferred to evaluation board. Second one is connection box. Because the output type of sensor and input type of evaluation board is different, connection box was necessary. Third one was evaluation board. The signal from the sensor was converted to digital signal in evaluation board. And this signal was transferred to device server. Fourth one was device server Device server transferred the data from evaluation board to main computer. And the last one was other parts controlled by main computer. In main computer, there were communication and diagnosis algorithms. The result was derived by main computer. In the result, there were 12 categories and 5 levels of motor conditions. The proposed system had some advantages comparing with stand alone type commercial motor fault diagnosis system. The first, by using remote access it was easier to get the conditions of motor. The second, there was no need to handle the sensors when users measured the motor signals. By this property, no one was necessary at motor location site. The third, this system was less restricted by times and places than commercial stand alone type diagnosis system. Therefore users can operate this system only using the main computer. Once the sensors are installed at the motor, users doesn't need to move to check up the condition of motors. Moreover, if there is ethernet hub, many motors can be not only diagnosed at once but also decreased its cost.

• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.103-109
• /
• 2015

This paper introduces a multi-purpose smart fusion sensor. Normally, this type of sensor can contribute to energy savings specifically related to lighting and heating/air conditioning systems by detecting individuals in an office building. If a fire occurs, the sensor can provide information regarding the presence and location of residents in the building to a management center. The system consists of four sensors: a thermopile sensor for detecting heat energy, an ultrasonic sensor for measuring the distance of objects from the sensor, a fire detection sensor, and a passive infrared sensor for detecting temperature change. The system has a wireless communication module to provide the management center with control information for lighting and heating/air conditioning systems. We have also demonstrated the usefulness of the proposed system by applying it to a real environment.

• 센서학회지
• /
• 제16권4호
• /
• pp.247-253
• /
• 2007

Low power consumption sensor network platform (sensor node) for sensor networking with IEEE 802.15.4 protocol was fabricated. The sensor node used ceramic bar type antenna for increasing RF signal performance and decreasing PCB size occupied by antenna. The communication range of the fabricated sensor node was about $20{\sim}30$ m in open environment with 915 MHz frequency bandwidth and well supported by Tiny OS. The sensor node have good connectivity with various external devices by RS-232, I2C, analogue and digital expansion board, hence, this sensor node can be applied to various applications in wireless sensor network and ubiquitous sensor network.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.156-167
• /
• 2014

This paper presents the test results of small dipstick-gage-type engine-oil-deterioration-detection sensor. The measured sensor signal characteristics for the capacitance and temperature are analyzed. The engine oil deterioration condition correlates with the electrical property of the dielectric constant that comprised with physical properties such as TAN (Total Acid Number), TBN (Total Base Number) and viscosity. Several problems encontered during the test of the sensor system are improved. The results of vehicle tests show that the capacitance signal is stable after the engine stops. Therefore, the sensor should start measuring the parameters for monitoring the engine oil condition after the engine stops. The engine is considered to be in a stopped state if the difference between the maximum and minimum values of the oil capacitance measured every 1 min is below 0.02 pF. The key test results in this paper will help in the development of an engine oil change warning algorithm.

• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.28-35
• /
• 2015

This paper introduces a resistance scanning-type flexible tactile sensor for intelligent robots and presents the output characteristics of the sensor via signal processing. The sensor was produced via the lamination method using multi-walled carbon nanotubes (a conductive material), an insulator, and Tango-plus (an elastic material). Analog and digital signal processing boards were produced to analyze the output signal of the sensor. The analog signal processing board was made up of an integrator and an amplifier for signal stability, and the digital signal processing board was made up of an IIR filter for noise removal. Finally, the sensor output for the contact force was confirmed through experiments.

• Journal of Electrical Engineering and Technology
• /
• 제3권4호
• /
• pp.559-565
• /
• 2008

This study designed a new type of loop antenna that is able to detect partial discharges based on microstrip line technology. In the diagnosis of power cables, partial discharge signals are generally produced at a frequency range less than 100MHz because high frequency PD signals are lost along a propagation path in such cables. The new type of loop antenna sensor has been studied using simulation software known as CST microwave studio version 5.0. In partial discharge measurement experiments, a commercial HFCT sensor was used as a reference sensor. Several experiments were made over HFCT and loop antenna sensors for detecting partial discharges on 22.9kV MV XLPE cable. In this study, we showed the loop antenna designed in this study that can be applied as a commercial HFCT sensor.

• 센서학회지
• /
• 제11권3호
• /
• pp.138-144
• /
• 2002

스테인레스 봉입형 압력센서를 제작하기 위하여 먼저 반도체 제조 및 식각 공정을 통하여 반도체 압력센서를 제작하였다 그리고 이를 glass molding된 스테인레스 housing에 올려놓고 $50\;{\mu}m$ 두께의 스테인레스 박판을 용접한 후 실리콘 오일을 채워 넣고 봉입하여 압력 범위 10 bar 센서를 완성하였다. 이와 같이 제작한 센서와 XTR105 발신기 전용 회로를 결합하여 $4{\sim}20\;mA$ 출력의 압력 발신기를 제작하고 그 특성을 조사하였다. 온도 보상 전 정확도는 ${\pm}5%$ FS이었으나 보상 후 정확도 ${\pm}1%$ FS로 개선되었다.

• 전기학회논문지
• /
• 제62권3호
• /
• pp.395-400
• /
• 2013

In this paper, we introduce the implementation of high accurate level sensor system using the pulse wave type magnetostriction sensor. When a current pulse flows along the waveguide, the magnetic field also propagates towards the end of waveguide. When this magnetic field just passes the position of the magnet for level detection, the resultant magnetic field by these two magnetic fields makes a torsional reflected signal. This is used to calculate the time difference between a interrogation pulse wave and this torsional reflected signal. The key elements and characteristics were investigated to implement level sensor system based on this principle. We introduce a method to calculate the speed of ultrasonic reflected signal and how to make a model of sensing coil. In particular, we experiment with the characteristics of the torsional reflected signal according to the changes of the interrogation voltage and displacement. To make high accurate level sensor system, two methods were compared. One is to use the comparator and time counter, the other is STFT(Short Time FFT) which is capable of the time-frequency analysis.