• Structural Engineering and Mechanics
• /
• v.89 no.6
• /
• pp.589-599
• /
• 2024

This study presents the usability of the high-rate single-frequency Precise Point Positioning (SF-PPP) technique based on 20 Hz Global Positioning Systems (GPS)-only observations in detecting dynamic motions. SF-PPP solutions were obtained from post-mission and real-time GNSS corrections. These include the International GNSS Service (IGS)-Final, IGS real-time (RT), real-time MADOCA (Multi-GNSS Advanced Demonstration tool for Orbit and Clock Analysis), and real-time products from the Australian/New Zealand satellite-based augmentation systems (SBAS, known as SouthPAN). SF-PPP results were compared with LVDT (Linear Variable Differential Transformer) sensor and single-frequency relative positioning (SF-RP) solutions. The findings show that the SF-PPP technique successfully detects the harmonic motions, and the real-time products-based PPP solutions were as accurate as the final post-mission products. In the frequency domain, all GNSS-based methods evaluated in this contribution correctly detect the dominant frequency of short-term harmonic oscillations, while the differences in the amplitude values corresponding to the peak frequency do not exceed 1.1 mm. However, evaluations in the time domain show that SF-PPP needs high-pass filtering to detect accurate displacement since SF-PPP solutions include trends and low-frequency fluctuations, mainly due to atmospheric effects. Findings obtained in the time domain indicate that final, real-time, and MADOCA-based PPP results capture short-term dynamic behaviors with an accuracy ranging from 3.4 mm to 8.5 mm, and SBAS-based PPP solutions have several times higher RMSE values compared to other methods. However, after high-pass filtering, the accuracies obtained from PPP methods decreased to a few mm. The outcomes demonstrate the potential of the high-rate SF-PPP method to reliably monitor structural and earthquake-induced ground motions and vibration frequencies of structures.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.828-830
• /
• 2002

Axial Flux Permanent Magnet motor could widely be used for low speed and high torque applications. In this paper, to analyse the sensor positioning effect of AFPM motor which has a new concentric winding method and to calibrate the switching timing according to speed, prototype motor is manufactured. As a result of experiment, advance angle from 30 degree to 45 degree of sensor position is more proper. So, this results can be used for design of sensor position to improve characteristic of the dual gap AFPM with coreless and slotless.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.221-226
• /
• 2004

For comparing more than two images, the precise geometric corrections should be preceded because it necessary to eliminate systematic errors due to basic sensor information difference and non-systematic errors due to topographical undulations. In this study, we did sensor modeling using satellite sensor information to make a basic map of change detection for artificial topography. We eliminated the systematic errors which can be occurred in photographing conditions using GCP and DEM data. The Kompsat EOC images relief could be reduced by precise rectification method. Classifying images which was used for change detections by city and forest zone, the accuracy of the matching results are increased by 10% and the positioning accuracies also increased.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.2
• /
• pp.89-96
• /
• 2017

We develop an embedded system to measure various sensor data, control multiple motors, and communicate with mobile devices for system managements. Choosing TI AM3359 microprocessor featuring high processing performance, low power consumption, and various I/O device support, we design and build the embedded system hardware so that it supports multiple global positioning system (GPS) and gyro sensor modules to measure precise position; multiple pulse width modulation (PWM) outputs to control multiple direct current (DC) motors; a Bluetooth module to communicate with mobile devices. Then, we port the boot loader and device drivers to the built circuit board and construct the firmware development environment for the application programming. The performance of the designed and implemented embedded system is demonstrated by real motor control test using GPS and gyro sensor data and control parameters configured by a mobile device.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.197-203
• /
• 2010

The problem of location awareness in wireless sensor networks where nodes use GPS (Global Positioning System), remains challenging problem, when considering the required large energy consumption during the localization phase. In this paper we designed hardware for GPS based localization and propose a framework, called ELS, to consume low cost energy. In the ELS framework, sensor nodes are equipped with GPS. Because GPS spends large energy for position awareness, conventional localization algorithms cannot use GPS-device. We try to find a solution for efficient energy expenditure of GPS. Finally, we derive optimal transmission power of GPS data and a scheme of localization through experiment and simulation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.1
• /
• pp.85-91
• /
• 2000

Underwater sensor accuracy test which measures the detection range and bearing accuracies of sonar simulates sonar transmitting ping and underwater radiating noise of target vessels. In this test, because the position of sonar target is the reference position of test, the sonar target position should be precisely estimated. Hence, this paper suggests to apply USBL algorithm which adopts cross phase spectrum of received sensor signals, and presents its performance by range and bearing estimation simulations. As a result of simulations, suggested algorithm shows good accuracy for underwater sensor accuracy test near 5㏈ SNR.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.288-291
• /
• 2001

This paper present effective odometry error compensation using multisensor fusion for the accurate positioning of mobile robot in navigation. During obstacle avoidance and wall following of mobile robot, position estimates obtained by odometry become unrealistic and useless because of its accumulated errors. To measure the position and heading direction of mobile robot accurately, odometry sensor a gyroscope and an azimuth sensor are mounted on mobile robot and Complementary-filter is designed and implemented in order to compensate complementary drawback of each sensor and fuse their information. The experimental results show that the multisensor fusion system is more accurate than odometry only in estimation of the position and direction of mobile robot.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.560-564
• /
• 1999

Burr sensing for burr size measurement and deburring process control is one of the essential elements in an automated deburring procedure. This paper presents the implementation of capacitance sensing and acoustic emission (AE) to deburring. The first application is the "on-line" measurement of burrs using a capacitance sensor. A non-contact capacitance gauging sensor is attached to an ultra precision milling machine which was used as a positioning system. The setup is used to measure burr profiles along machined workpiece edges. The proposed scheme is shown to be accurate, easy to setup, and with minor modifications, readily applicable to automatic deburring processes. As the second example, AE signals were sampled and analyzed for the sensor feedback of a precision deburring process - laser deburring -. The results, such as the sensitivity of AE signals to burr shapes and edge detection capability show a clear correlation between physical process parameters and the AE signals. A subsequent control strategy for deburring automation is also briefly discussed.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.274-277
• /
• 2002

This paper deals with the attitude determination using GPS carrier phase. The main factors on attitude reliability are accuracy, error factors and the real-time ambiguity resolution speed. Firstly, these factors are reviewed. And then, the attitude reliability is improved by applying the averaging method. Finally, the attitude determination software is verified by the experiments. The accuracy of the proposed attitude determination method is 0.013$^{\circ}$ PE in live test. This result is more accurate than the existing INS equipment.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.283-286
• /
• 2002

For the satisfying performance of a oil lubricator, design of a oil controller for the system which meets the required specifications and its supporting hardware that keep their functioning is important. Among the hardware of a control system, oil system are most vulnerable to malfunction. Thus it is necessary to keep track of accurate and reliable oil readings for good fusion oil lubricator performance. In case of oil lubricator ,data loss, ssr trigger error faults, they are detected by examining the data system output values and the major values of the system, and then the faults are recognized by the analysis of symptoms of faults. If necessary electronic -sensor values are synthesized according to the types of faults, and then they are used for the controller instead of the raw data. In this paper, a fast-32bit cpu micorprocessor applied to the control of flexible link system with the sensor fault problems in the error module fer exact positioning to show the applicability. It is shown that the fusion oil lubricator can provide a satisfactory loop performance even when the sensor faults occure