• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.219-219
• /
• 2008

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for ubiquitous sensor networks (USN). There are several power generating methods such as thermal gradients, solar cell, energy produced by human action, mechanical vibration energy, and so on. Most of all, mechanical vibration is easily accessible and has no limitation of weather and environment of outdoor or indoor. In particular, the piezoelectric energy harvesting from ambient vibration sources has attracted attention because it has a relative high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system hassome drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure. In this case, the energy harvester has a lower natural frequency under 200 Hz than a normal cantilever structure. Moreover, it has higher an energy conversion efficient because shear mode ($d_{15}$) is much larger than 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate as a standalone power generator for USN.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.4
• /
• pp.32-38
• /
• 2011

This paper describes implementation of the 5.0GHz RF frequency synthesizer with 0.18${\mu}m$ silicon CMOS technology being used as an application of the IEEE802.15.4 USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma}-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get excellent performance of high speed and wide tuning range, N-P MOS core structure and 12 step cap banks have been used in design of the VCO. The chip area including pads for testing is $1.1{\times}0.7mm^2$, and the chip area only core for IP in SoC is $1.0{\times}0.4mm^2$. Through analysing of the fabricated frequency synthesizer, we can see that it has wide operation range and excellent frequency characteristics.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.3
• /
• pp.37-42
• /
• 2007

This paper reconsiders established power conservation models for ubiquitous sensor networks that use relay nodes instead of direct communication and proposes novel network power consumption model with consideration of the channel level and radio chip level simultaneously. We estimate the effect of minimum hop-count policy in terms of network power consumption through simulation of various situations for low power RF module CC2420. It is observed that maximum RF power and minimum hop-count results in lower energy consumption relatively. Also, in total network energy consumption, which is included re-transmission, minimum hop count policy presents decrease by 33.1% of energy consumption in compare with the conventional model.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.3
• /
• pp.49-56
• /
• 2007

The IEEE 802.15.4 low rate wireless personal area network is a protocol suitable for wireless sensor networks. Thus there has been growing interest in the IEEE 802.15.4 protocol in the home automation networks. This paper proposes a scheduling scheme obtaining optimal parameters regarding the IEEE 802.15.4 frame and subframes in the home automation networks. Guaranteed time slots (GTS) are exploited for the delivery of real-time traffic. Given a set of the requirements for bandwidths and periods assigned to nodes in the network, the beacon interval and the active/inactive subframe duration satisfying the requirements are selected considering the low duty cycle by the proposed scheme. Based on these parameters, analytic results provide the way to efficient use of network resources including energy.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.3
• /
• pp.1204-1227
• /
• 2020

The tradeoff between energy conservation and traffic balancing is a dilemma problem in Wireless Sensor Networks (WSNs). By analyzing the intrinsic relationship between cluster properties and long distance transmission energy consumption, we characterize three node sets of the cluster as a theoretical foundation to enhance high performance of WSNs, and propose optimal solutions by introducing rendezvous and Mobile Elements (MEs) to optimize energy consumption for prolonging the lifetime of WSNs. First, we exploit an approximate method based on the transmission distance from the different node to an ME to select suboptimal Rendezvous Point (RP) on the trajectory for ME to collect data. Then, we define data transmission routing sequence and model rendezvous planning for the cluster. In order to achieve optimization of energy consumption, we specifically apply the economic theory called Diminishing Marginal Utility Rule (DMUR) and create the utility function with regard to energy to develop an adaptive energy consumption optimization framework to achieve energy efficiency for data collection. At last, Rendezvous Transmission Algorithm (RTA) is proposed to better tradeoff between energy conservation and traffic balancing. Furthermore, via collaborations among multiple MEs, we design Two-Orbit Back-Propagation Algorithm (TOBPA) which concurrently handles load imbalance phenomenon to improve the efficiency of data collection. The simulation results show that our solutions can improve energy efficiency of the whole network and reduce the energy consumption of sensor nodes, which in turn prolong the lifetime of WSNs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.5
• /
• pp.49-54
• /
• 2009

This paper describes implementation of the 1.9GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma }-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.2{\times}0.7mm^2$, and the chip area only core for IP in SoC is $1.1{\times}0.4mm^2$. The test results show that there is no special spurs except -63.06dB of the 6MHz reference spurs in the PLL circuitry. There is good phase noise performance like -116.17dBc/Hz in 1MHz offset frequency.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.6
• /
• pp.87-93
• /
• 2008

This paper describes implementation of the 5.0GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the IEEE802.15.4 USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma}-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.1*0.7mm^2$, and the chip area only core for IP in SoC is $1.0*0.4mm^2$. Through comparing and analysing of the designed two kind of the frequency synthesizer, we can conclude that if we improve a litter characteristics there is no problem to use their as IPs.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.17-24
• /
• 2010

This paper presents calorie expenditure prediction model of daily activity of elderly living alone for LBS(Location Based Service) applications. The proposed method is to describe the daily activity patterns of older adult using PIR (Passive InfraRed) motion sensors and to examine the relationships between physical activity and calorie expenditure. The developed motion detecting system is composed of a sensing system and a server system. The motion detecting system is a set of wireless sensor nodes which has PIR sensor to detect a motion of elder. Each sensing node sends its detection signal to a home gateway via wireless link. The home gateway stores the received signals into a remote database. The server system is composed of a database server and a web server, which provides web-based monitoring system to caregivers for more effective services. The experiment results show the adaptability and feasibility of the calorie expenditure model.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.348-353
• /
• 2008

Despite the increasing popularity of wireless sensor network, indoor positioning using low power IEEE 802.15.4 compliant radio had attracted an interest of many researchers in the last decade. Old fashionable indoor location sensing information has been presented in dull and unpleasant 2D image standard. This paper focused on visualizing high precision 3 dimensional RSSI-based (received signal strength indication) spatial sensing information in an interactive virtual reality on PDA. The developed system operates by capturing and extracting signal strength information at multiple pre-defined reference nodes to provide information in the area of interest, thus updating user's location in 3D indoor virtual map. VRML (Virtual Reality Modeling Language) which specifically developed for 3D objects modeling is utilized to design 3D indoor environment.

• Journal of Korea Spatial Information System Society
• /
• v.10 no.1
• /
• pp.51-63
• /
• 2008

Previous studies for routing In USN (Ubiquitous Sensor Networks) appear to be unreliable due to the dependence on non-spatial data and the lack of map overlay analysis. Multiple spatial parameters and radio propagation modeling techniques were integrated to derive RSSI (Received Signal Strength Indicator) value between route nodes and produce a highly reliable path map. It was possible to identify area-wide patterns of USN route subject to many different Influences (e.g. the specific effects of radio blocking factors such as the visible area, road area, cell duplicated area, and building density), which cannot be acquired by traditional non-spatial modeling. The quantitative evidence concerning the USN route for individual cell as well as entire study area would be utilized as major tools to visualize paths in real-time and to select alternative path when failure or audition of route node occurs.