• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.32-36
• /
• 2008

An HTS conductor with parallel HTS tapes is essential for a large power HTS device to flow a large current. One of the most important factor for this conductor is a current distribution. Non-uniform current distribution in parallel tapes makes the critical current of the conductor low and the AC losses high. In this paper we proposed a non-contact method which measured each current in parallel tapes by using an array of Hall sensors. A matrix can be derived from this array for calibration. The current distributions of 4 and 6 parallel tapes were measured.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2023.05a
• /
• pp.298-300
• /
• 2023

자율주행 및 robot navigation 시스템에서 물체 인식 성능향상을 위해 대부분 MSF(Multi-Sensor Fusion) 기반 설계를 한다. 따라서 각 센서로부터 들어온 정보를 정합하는 것은 정확한 MSF 알고리즘을 위한 필요조건이다. 다양한 선행 연구에서 2D 데이터에 대한 공격을 진행했다. 자율주행에서는 3D 데이터를 다루어야 하므로 선행 연구에서 하지 않았던 3D 데이터 공격을 진행했다. 본 연구에서는 스케일링 공격 기반 카메라-라이다 센서 간 정합 모델의 정확도를 저하시키는 공격 방법을 제안한다. 제안 방법은 입력 라이다의 포인트 클라우드에 스케일링 공격을 적용하여 다운스케일링 단계에서 공격하고자 한다. 실험 결과, 입력 데이터에 공격하였을 때 공격 전보다 평균제곱 이동오류는 56% 이상, 평균 사원수 각도 오류는 98% 이상 증가했음을 보였다. 다운스케일링 크기 별, 알고리즘별 공격을 적용했을 때, 10×20 크기로 다운스케일링 하고 lanczos4 알고리즘을 적용했을 때 가장 효과적으로 공격할 수 있음을 확인했다.

• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.86-94
• /
• 2009

Temperature measurement capability was inter-compared using the transfer standard platinum resistance thermometers(SPRT) among four laboratories of KRISS. The transfer SPRTs were primarily calibrated at the triple point of water and Ga melting point, then used at inter-comparison experiment. Temperature difference of calibration value between temperature laboratory and length laboratory at $20^{\circ}C$ was -0.7 mK and +2.4 mK at density laboratory. Temperature measured near $20^{\circ}C$, $25^{\circ}C$ and $30^{\circ}C$ at fluid flow laboratory was deviated by $34.2{\sim}80.4\;mK$ from the calibration values of the transfer SPRT. Ga melting points was inter-compared among three laboratories, and the difference of Ga melting points against the standard Ga melting point of temperature laboratory were $0.03{\sim}0.54\;mK$ at length laboratory and 0.02 mK at density laboratory.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.173-181
• /
• 2015

We developed a wireless gamma-ray probe based on radiation photon counting method to diagnose and detect remaining lesions after surgery, and its effectiveness was evaluated using calibration sources and a phantom. The probe was designed and miniaturized using a semi-conductor-based radiation sensor, and a Bluetooth remote communication module was used to implement the wireless diagnosis and detection system. Moreover, a remote monitoring system was implemented to monitor affected areas during diagnosis and surgery. To assess the effectiveness of the developed probe in this study, calibration sources $^{57}Co$, $^{133}Ba$, $^{22}Na$ and $^{137}Cs$ and a chicken breast phantom were used. Furthermore, the probe's detection response to gamma ray was confirmed through evaluation. Its clinical applicability was verified by assessing the response linearity and detection direction according to gamma-ray intensity, as well as the detection efficiency according to the depth of the gamma source in the phantom.

• Journal of Broadcast Engineering
• /
• v.7 no.1
• /
• pp.2-9
• /
• 2002

Recently. VR( Virtual Reality) applications such as virtual studio and virtual character are wifely used In TV programs. and AR( Augmented Reality) applications are also belong taken an interest increasingly. This paper introduces a virtual screen system. which Is a new AR application for broadcasting. The virtual screen system is a real-time video augmentation system by tracking a chroma-patterned moving panel. We haute recently developed a virtual screen system.'K-vision'. Our system enables the user to hold and morse a simple panel on which live video, pictures of 3D graphics images can appear. All the Images seen on the panel change In the correct perspective, according to movements of the camera and the user holding the panel, in real-time. For the purpose of tracking janet. we use some computer vision techniques such as blob analysis and feature tracking. K-vision can work well with any type of camera. requiring no special add-ons. And no need for sensor attachments to the panel. no calibration procedures required. We are using K-vision in some TV programs such as election. documentary and entertainment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.47-54
• /
• 2013

This paper introduces a W-band millimeter-wave power standard transfer system using the direct comparison method. The transfer system was developed to evaluate the effective efficiency and calibration factor of a W-band waveguide power sensor. The evaluation method and the measured results of the directional coupler that characterizes the calibration system are studied. The uncertainties of the standard transfer system are investigated, and the major uncertainty contributors are discussed as well. The performance of the realized W-band power standard transfer system was verified by comparing results with reference values.

• Journal of Sensor Science and Technology
• /
• v.15 no.4
• /
• pp.257-262
• /
• 2006

A Fe-C eutectic cell for thermocouple calibration was manufactured and tested to investigate its phase transition characteristics in the thermocouple thermometry. It was observed that the freezing plateaus were strongly affected by the freeze-inducing temperature $T_{f}$. In case of the melting process, the melting plateau was influenced by the previous thermal history. As $T_{f}$. in the previous freezing was lower, the melting plateau became lower with a temperature dependence as small as $-0.0015^{\circ}C/^{\circ}C$. Therefore, it was found that the freeze-inducing temperature should be fixed to obtain a reproducible phase transition temperature in the melting. After fixing $T_{f}$, the melting process was examined and it was found that long and flat melting plateau was obtained within a reproducibility of about ${\pm}0.01^{\circ}C$. Based on the observed results, it was recommended that Fe-C eutectic temperature be best realized for the melting process with a melt-inducing temperature of $+3^{\circ}C$ above the expected liquidus temperature after freezing at $-5^{\circ}C$ below the solidus temperature.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.18 no.1
• /
• pp.32-39
• /
• 2013

Although space-borne satellites are useful in obtaining information all around the world, they cannot observe at a suitable time and place. In order to overcome these limitations, an airborne remote sensing system was developed in this study. It is composed of a SAR sensor and a thermal infrared sensor. Additionally GPS, IMU, and thermometer/hygrometer were attached to the plane for radiometric and geometric calibration. The brightness of SAR image varies depending on surface roughness, and capillary waves on the sea surface, which are easily generated by sea winds, induce the surface roughness. Thus, sea surface wind can be estimated using the relationship between quantified SAR backscattering coefficient and the sea surface wind. On the other hand, thermal infrared sensor is sensitive to measure object's temperature. Sea surface temperature is obtained from the thermal infrared sensor after correcting the atmospheric effects which are located between sea surface and the sensor. Using these two remote sensing sensors mounted on airplane, four test flights were carried out along the west coast of Korea. The obtained SAR and thermal infrared images have shown that these images were useful enough to monitor coastal environment and estimate marine meteorology data.

• Korean Journal of Crystallography
• /
• v.8 no.1
• /
• pp.38-47
• /
• 1997

A new weighing sensor for the automatic diameter control system of the crystal growth is developed in this study. This weighing sensor measures the frequency of the vibrating element which is lineally changing with respect to weight. The signal and the power of this system are transmitted without any physical contact, so that this sensor offers high accuracy and resolution. This system consists of a string, a sinusoidal wave generator, an automatic amplification adjusting circuit, signal transformers and a PCB. 4 kinds of programs are developed for checking DAC, weight calibration and controlling growth process. The measurements of the standard deviation and the resolution show $\pm0.10g$(measured at every second) and $5{\times}10^{-5}$, respectively, This weighing sensor is effective under high pres-sure of 200 atm, high temperature and vacuum condition. The weighing system can control the temperature in the accuracy of $\pm0.025^{\circ}C$ with the 'signal divider'. The optical quality single crystals of $(YGd)_3Sc_2Ga_3O_{12},\;Er-Y_3Sc_2Al_3O_{12},\;and\;Bi_{12}GeO_{20}$ have been grown by Czo-chralski method using this auto-diameter control system.

• Journal of Bio-Environment Control
• /
• v.30 no.1
• /
• pp.27-36
• /
• 2021

A capacitive water sensor was developed to measure the capacitance over a wide part of a substrate using an insulated electrode plate (30 cm × 10 cm) with copper and Teflon attached on either side of the substrate. This study aimed to convert the capacitance output obtained from the condenser-type capacitance sensor into the substrate water content. The quantification experiment was performed by measuring the changes in substrate water weight and capacitance while providing a nutrient solution and by subsequently comparing these values. The substrate water weight and capacitance were measured every 20 to 30 seconds using the sensor and load cell with a software developed specifically for this study. Using a curve-fitting program, the substrate water content was estimated from the output of the capacitance using the water weight and capacitance of the substrate as variables. When the amount of water supplied was increased, the capacitance tended to increase. Coefficient of variation (CV) in capacitance according to the water weight in substrate was greater with the 1.0 kg of water weight, compared with other weights. Thus, the fitting was performed with higher than 1.0 kg, from 1.7 to 6.0 kg of water weight. The correlation coefficient between the capacitance and water weight in substrate was 0.9696. The calibration equation estimated water content from the capacitance, and it was compared with the substrate water weight measured by the load cell.