• Journal of Fisheries and Marine Sciences Education
• /
• v.19 no.3
• /
• pp.323-328
• /
• 2007

This paper was studied on the effect of the specific resistance of water on corrosion characteristics of STS 304 for gas boiler. The electrochemical polarization test of STS 304 for gas boiler was carried out. And the polarization resistance, uniform corrosion, corrosion behavior by impressed potential and corrosion sensitivity of STS 304 with specific resistance were considered. The main results are as following: 1) With being low the specific resistance of water, the polarization resistance and corrosion potential of STS 304 decreases, while corrosion current density increases. 2) Under constant impressed potential, the corrosion sensitivity of STS 304 is large with being low the specific resistance due to synergy effect of Cl ion.

• Fibers and Polymers
• /
• v.2 no.1
• /
• pp.140-143
• /
• 2001

To better understand the formation of necking in drawing processes of fibers, strain distributions during drawing processes have been analyzed. For simplicity, one-dimensional incompressible steady flow at a constant temperature was assumed and quasi-static model was used. To describe mechanical properties of solid polymers, non-linear visco-plastic material properties were assumed using the power law type hardening and rate-sensitive equation. The effects of various parameters on the neck formation were matematically analyzed. As material property parameters, strain-hardening parameter, visco-elastic coefficient and strain-rate sensitivity were considered and, for process parameters, the drawing ratio and the process length were considered. It was found that rate-insensitive materials do not reach a steady flow state and the rate-sensitivity plays a key role to have a steady flow. Also, the neck formation is mainly affected by material properties, especially for the quasi-static model. If the process length changes, the strain distribution was found to be proportionally re-distributed along the process line by the factor of the total length change.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.1067-1072
• /
• 1996

Sensitivity analysis of the cylindrical zigzag cams under acceleration and centrifugal forces is performed. A Lagrangian method is used to determine the mechanism constant of zigzag track, And the equation of motion for cylindrical zigzag cam under rectangular pulse is derived by the governing equations of a single spring mass system. The ratio of the drive force tn resisting force is derived by angular acceleration, centrifugal force and setback force on the operation of the munition. The theoretical sensitivity curves for 3 models are analyzed. And experiments for 3 models are conducted to check safe and functional zone. Zigzag cam types can be satisfied all major design requirements for switch system of munition.

• Journal of radiological science and technology
• /
• v.20 no.1
• /
• pp.15-20
• /
• 1997

Unlike conventional CT scan, the helical CT scan uses continuous rotating CT equipment with a slip ring to move the patient's coach at a constant speed while continuously scanning. Slice sensitivity profiles in the Z-position(SSPz) using the conventional X-ray CT have a shape similiar to a rectangular wave, which slightly spreads out into plains below the mountain. However, in the helical CT, with an expansion of the base, the rectangular shape collapses and a mouatain-like shape can be seen. We need to investigate the fellowing factors in helical CT scanning;the ability to scan along the axis of the body, effective slice width, slice shape and the precision of coach velocity, Helical scanning with sprial X-ray track is different from the conventional scanning in terms of the principle of image reconstruction performed. We believe that the problems in helical scanning can be solved by understanding new the special parameters such as the bed moving speed and the interval of image reconstruction.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.11a
• /
• pp.76-80
• /
• 2001

The weight of shoes may serve as a determining factor of perceived comfort and feel to the consumer in their purchase and repurchase decisions of footwear. People, however, seem to have trouble in accurately judging the feeling of weight of shoes on their feet. This paper made a psychophysical study of subjects′ sensitivity to weight on their feet and in their hands. The experiment consisted of 3 tests according to the motions people make when they evaluate the feel of shoes: 1) vertical lifting of a shoe on the foot ("hefting" in on the foot) 2) swing the shod foot back and forth; 3) holding and lifting a shoe by hand ("hefting" it in the hand). The method of constant stimuli and magnitude estimation were used for the experiment with 20 subjects. Weber′s ratios and the power law exponents obtained for each of the three tests were 0.156 and 0.713, 0.108 and 0.970, and 0.065 and 1.249, respectively in the same order of the previously listed tests.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.54-59
• /
• 2006

An analytical solution for deflection-load characteristics of a conical disk spring used especially in the automotive manual transmission clutch applications is proposed in order to take into account the effects of friction and large deformation. The conical disk spring, or the diaphragm spring, has a hinge support, an application point of release load at the tip of the fingers and an application point of clamp load near but inside the outer perimeter of the conical disk spring. The friction coefficient is assumed to be a constant regardless of the speed of deflection and the magnitude of loads. Comparison with experimental shows a good agreement with the analytical prediction. Also, the sensitivity of the clamp load due to variations in the geometrical parameters of the conical disk spring is calculated and discussed.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.571-576
• /
• 2007

This study presents stiffness-based optimal design to control quantitatively lateral drift of frame-shear wall structures subject to seismic loads. To this end, lateral drift constraints are established by introducing approximation concept that preserves the generality of the mathematical programming and can efficiently solve large scale problems. Also, the relationships of sectional properties are established to reduce the number of design variables and resizing technique of member is developed under the 'constant-shape' assumption. Specifically, the methodology of dynamic displacement sensitivity analysis is developed to formulate the approximated lateral displacement constraints. The 12 story frame-shear wall structural models is considered to illustrate the features of dynamic stiffness-based optimal design technique proposed in this study.

• Journal of Magnetics
• /
• v.16 no.2
• /
• pp.114-119
• /
• 2011

This paper presents a magnetization modeling method combined with material sensitivity information to identify the unknown magnetization distribution of a hull and improve the accuracy of the predicted fields. First, based on the magnetization modeling, the hull surface was divided into three-dimensional sheet elements, where the individual remanent magnetization was assumed to be constant. For a fast search of the optimum magnetization distribution on the hull, a material sensitivity formula containing the first-order gradient information of an objective function was combined with the magnetization modeling method. The feature of the proposed method is that it can provide a stable and accurate field solution, even in the vicinity of the hull. Finally, the validity of the method was tested using a scale model ship.

• Journal of the Korea Society for Simulation
• /
• v.9 no.2
• /
• pp.89-102
• /
• 2000

In this paper, we consider an optimal allocation of constant service efforts in queueing network to maximize the system throughput. For this purpose, using the perturbation analysis, we apply a stochastic optimization algorithm to two types of queueing systems. Our simulation results indicate that the estimates obtained from a stochastic optimization algorithm for a two-tandem queuing network are very accurate, and those for closed loop manufacturing system are a little apart from the known optimal allocation. We find that as simulation time increases for obtaining a new gradient (performance measure with respect to decision variables) by perturbation algorithm, the estimates tend to be more stable. Thus, we consider that it would be more desirable to have more accurate sensitivity of performance measure by enlarging simulation time rather than more searching steps with less accurate sensitivity. We realize that more experiments on various types of systems are needed to identify such a relationship with regards to stopping rule, the size of moving step, and updating period for sensitivity.

• Journal of electromagnetic engineering and science
• /
• v.11 no.1
• /
• pp.1-4
• /
• 2011

In this letter, we propose a novel tag antenna that has low performance degradation with nearby dielectric material. We obtained a stable reading performance and a broad matching bandwidth on nearby dielectric materials by employing a T-matching network with thick line width and capacitively slot-loaded arms. We then built the proposed antenna and measured the tag sensitivity to examine the reading characteristics with nearby dielectric materials. The measured results clearly demonstrate stable tag sensitivity with various nearby dielectric materials, such as foam, acrylic-plastic, glass, and ceramic plates. To more closely observe the antenna characteristics with nearby dielectric materials, we also examined the impedance variation and surface current distribution with respect to the dielectric constant of nearby target objects, which ranged from $1{\times}{\varepsilon}_0$ to $16{\times}{\varepsilon}_0$.