• 센서학회지
• /
• 제3권2호
• /
• pp.40-49
• /
• 1994

$CaF_{2}$ 불화물 고체전해질을 모물질로하는 저온동작용($300^{\circ}C{\sim}$500^{\circ}C) 산소센서를 제조하였다. $CaF_{2}$ 산소센서는 수축률과 SEM사진의 결과를 토대로 $850^{\circ}C$-3hr 동안 열처리 하였다. 디스크형 산소 센서는 기준전극으로 Air($O_{2}:21%$)|Pt를, 전해질로는 $CaF_{2}$, 감지전극으로 Pt를 사용하였으며, 기준전극 내장형 산소센서는 기준전극으로 NiO/Ni (30:70)을 사용하였다. 디스크형 산소센서의 경우 측정온도 $400^{\circ}C$에서 산소농도($0.1 %{\sim}10%$)로 변화시 45mV 정도의 기전력 변화를 보였으며, 기준전극 내장형의 경우는 40mV의 변화를 보였다.

• 센서학회지
• /
• 제4권4호
• /
• pp.16-22
• /
• 1995

메탄, 프로판가스를 검출하기 위하여 ${\gamma}-Al_{2}O_{3}$ 담체에, Pd 촉매를 섞어서 접촉연소식 센서 및 digital 계측기를 제작한 후 그 소자특성 및 계측기로서 응용가능성을 조사하였다. 본 연구에서 제조된 센서는 인가전압 2 V에 소모전력은 700mW가 나왔고, 출력전압변화는 1,000ppm의 프로판의 경우 약 700mV, 메탄의 경우 500mV 변화를 나타냈다. 계측기에서는 2,400ppm을 10회 반복적으로 주입시켜 측정하였다. 그 결과로, ${\pm}25ppm({\pm}1%)$의 오차를 보였고, 감도, 선형성, 재현성이 우수한 것을 볼 수 있었다.

• 센서학회지
• /
• 제27권2호
• /
• pp.93-98
• /
• 2018

In this paper, an energy-efficient 11.49-bit successive approximation register (SAR) capacitance-to-digital converter (CDC) for capacitive sensors with a figure of merit (FoM) of 31.6 pJ/conversion-step is presented. The CDC employs a SAR algorithm to obtain low power consumption and a simplified structure. The proposed circuit uses a capacitive sensing amplifier (CSA) and a dynamic latch comparator to achieve parasitic capacitance-insensitive operation. The CSA adopts a correlated double sampling (CDS) technique to reduce flicker (1/f) noise to achieve low-noise characteristics. The SAR algorithm is implemented in dual operating mode, using an 8-bit coarse programmable capacitor array in the capacitance-domain and an 8-bit R-2R digital-to-analog converter (DAC) in the charge-domain. The proposed CDC achieves a wide input capacitance range of 29.4 pF and a high resolution of 0.449 fF. The CDC is fabricated in a $0.18-{\mu}m$ 1P6M complementary metal-oxide-semiconductor (CMOS) process with an active area of 0.55 mm2. The total power consumption of the CDC is $86.4{\mu}W$ with a 1.8-V supply. The SAR CDC achieves a measured 11.49-bit resolution within a conversion time of 1.025 ms and an energy-efficiency FoM of 31.6 pJ/step.

• 자원환경지질
• /
• 제37권4호
• /
• pp.425-436
• /
• 2004

본 연구의 목적은 2002년 태풍 루사로 인해 강릉지역에서 발생한 산사태와 관련 요인들 간의 공간적 관계를 분석하는 것이다. 산사태 위치는 위성영상 및 현지조사를 실시하여 탐지하였다. 지형도, 토양도, 임상도, 지질도, 토지피복도 등을 GIS를 이용하여 공간 데이터베이스로 구축되었고, 이러한 데이터베이스로부터, 경사, 경사방향, 곡률, 수계, 지형 종류, 토질, 토앙모재, 토앙배수, 유효토심, 임상종류, 임상경급, 임상영급, 임상밀도, 암상, 토지피복도, 선구조도 등이 산사태 발생요인으로 이용되었다. 빈도비 모델을 이용하여 산사태와 발생 요인 간의 공간적 관계를 추출하였다. 그 결과인 공간적 상관관계는 2002년 루사로 인한 산사테의 특성을 설명하고, 산사태 취약성도를 작성하는데 이용될 수 있다.

• 한국소음진동공학회논문집
• /
• 제25권12호
• /
• pp.830-842
• /
• 2015

This paper aims to develop a SI(structural identification) technique using the kinetic energy optimization technique(KEOT) and the direct matrix updating method(DMUM) to decide on optimal location of sensors and to update FE model respectively, which ultimately contributes to a composition of more effective SHM. Owing to the characteristic structural flexing behavior of cable bridges, which makes them vulnerable to any vibration, systematic and continuous structural health monitoring (SHM) is pivotal for them. Since it is necessary to select optimal measurement locations with the fewest possible measurements and also to accurately assess the structural state of a bridge for the development of an effective SHM, a SI technique is as much important to accurately determine the modal parameters of the current structure based on the data optimally obtained. In this study, the KEOT was utilized to determine the optimal measurement locations, while the DMUM was utilized for FE model updating. As a result of experiment, the required number of measurement locations derived from KEOT based on the target mode was reduced by approximately 80 % compared to the initial number of measurement locations. Moreover, compared to the eigenvalue of the modal experiment, an improved FE model with a margin of error of less than 1 % was derived from DMUM. Finally, the SI technique for long-span bridges proposed in this study, which utilizes both KEOT and DMUM, is proven effective in minimizing the number of sensors while accurately determining the structural dynamic characteristics.

• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.142-149
• /
• 2009

This paper proposes and demonstrates novel flexible contact force sensing devices for 3-dimensional force measurement. To realize the sensor, polyimide and polydimethylsiloxane are used as a substrate, which makes it flexible. Thin-film metal strain gauges, which are incorporated into the polymer, are used for measuring the three-dimensional contact forces. The force sensor characteristics are evaluated against normal and shear load. The fabricated force sensor can measure normal loads up to 4N. The sensor output signals are saturated against load over 4N. Shear loads can be detected by different voltage drops in strain gauges. The device has no fragile structures; therefore, it can be used as a ground reaction force sensor for balance control in humanoid robots. Four force sensors are assembled and placed in the four corners of the robot's sole. By increasing bump dimensions, the force sensor can measure load up to 20N. When loads are exerted on the sole, the ground reaction force can be measured by these four sensors. The measured forces can be used in the balance control of biped locomotion system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1472-1477
• /
• 2005

Recently, the performance development of the exhaust system of a car is very important. The most important part of parts that constructing the exhaust system of a car is a muffler. The muffler reducing the exhaust noise from the engine influence on the engine performance directly. The inner parts of the muffler construct with the baffle and perforated pipes and so on. In the recent study, the study to design the semi-active muffler sensing the exhaust gas pressure controlling the back pressure variably with a EVV progress activity. So that the inner parts of the muffler show the complicated turbulent flow phenomena because of pulsatile flow from the engine and the structural properties and so on. The qualitative and quantitative analysis about the turbulent flow phenomena of the inner parts of the muffler is required gradually. In this study, to analysis the flow field of the inner parts of the muffler, analysis results with the PIV measurement to be able to analysis the variable change of the time and the space. Therefore, try to show the design variables to need to design the inner parts of a muffler of a car.

• 한국재료학회지
• /
• 제20권4호
• /
• pp.223-227
• /
• 2010

Recently, one-dimensional semiconducting nanomaterials have attracted considerable interest for their potential as building blocks for fabricating various nanodevices. Among these semiconducting nanomaterials,, $SnO_2$ nanostructures including nanowires, nanorods, nanobelts, and nanotubes were successfully synthesized and their electrochemical properties were evaluated. Although $SnO_2$ nanowires and nanobelts exhibit fascinating gas sensing characteristics, there are still significant difficulties in using them for device applications. The crucial problem is the alignment of the nanowires. Each nanowire should be attached on each die using arduous e-beam or photolithography, which is quite an undesirable process in terms of mass production in the current semiconductor industry. In this study, a simple process for making sensitive $SnO_2$ nanowire-based gas sensors by using a standard semiconducting fabrication process was studied. The nanowires were aligned in-situ during nanowire synthesis by thermal CVD process and a nanowire network structure between the electrodes was obtained. The $SnO_2$ nanowire network was floated upon the Si substrate by separating an Au catalyst between the electrodes. As the electric current is transported along the networks of the nanowires, not along the surface layer on the substrate, the gas sensitivities could be maximized in this networked and floated structure. By varying the nanowire density and the distance between the electrodes, several types of nanowire network were fabricated. The $NO_2$ gas sensitivity was 30~200 when the $NO_2$ concentration was 5~20ppm. The response time was ca. 30~110 sec.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1999년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.485-490
• /
• 1999

Wind vector information over the ocean is currently obtained using multiple beam scatterometer data. The scatterometers on ERS-1/2 generate wind vector information with a spatial resolution of 50km and accuracies of $\pm$2m/s in wind speed and $\pm$20$^{\circ}$ in wind direction. Synthetic aperture radar (SAR) data over the ocean have the potential of providing wind vector information independent of weather conditions with finer resolution. Finer resolution wind vector information can often be useful particularly in coastal regions where the scatterometer wind information is often corrupted because of the lower resolution system characteristics which is often contaminated by the signal returns from the coastal areas or ice in the case of arctic environments. In this paper we tested CMOD_4 and CMOD_IFR2 algorithms for extracting the wind vector from SAR data. These algorithms require precise estimation of normalized radar cross-section and wind direction from the SAR data and the local incidence angle. The CMOD series algorithms were developed for the C-band, VV-Polarized SAR data, typically for the ERS SAR data. Since RADARSAT operates at the same C-band but with HH-Polarization, the CMOD series algorithms should not be used directly. As a preliminary approach of resolving with this problem, we applied the polarization ratio between the HH and VV polarizations in the wind vectors estimation. Two test areas, one in front of Inchon and several sites around Jeju island were selected and investigated for wind vector estimation. The new results were compared with the wind vectors obtained from CMOD algorithms. The wind vector results agree well with the observed wind speed data. However the estimation of wind direction agree with the observed wind direction only when the wind speed is greater than approximately 3.0m/s.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1999년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.439-442
• /
• 1999

It is important to analyze the seasonal change profiles of land cover type in large scale for establishing preservation strategy and environmental monitoring. Because the NOAA-AVHRR data sets provide global data with high temporal resolution, it is suitable for the land cover classification of the large area. The objectives of this study were to classify land cover of Korea, to investigate the phenological profiles of land cover. The NOAA-AVHRR data from Jan. 1998 to Dec. 1998 were received by Korea Ocean Research & Development Institute(KORDI) and were used for this study. The NDVI data were produced from this data. And monthly maximum value composite data were made for reducing cloud effect and temporal classification. And the data were classified using the method of supervised classification. To label the land cover classes, they were classified again using generalized vegetation map and Landsat-TM classified image. And the profiles of each class was analyzed according to each month. Results of this study can be summarized as follows. First, it was verified that the use of vegetation map and TM classified map was available to obtain the temporal class labeling with NOAA-AVHRR. Second, phenological characteristics of plant communities of Korea using NOAA-AVHRR was identified. Third, NDVI of North Korea is lower on Summer than that of South Korea. And finally, Forest cover is higher than another cover types. Broadleaf forest is highest on may. Outline of covertype profiles was investigated.