• 한국표면공학회지
• /
• 제19권3호
• /
• pp.92-108
• /
• 1986

An electroplating on the lead frame fabricated from domestic copper plate was studied experimentally. In this study, nickel was plated on the thin copper lead frame and silver layer was coated on the nickel film in the cyanide electrolyte. The effect of process variables such as current density, plating time, coating thickness and flow rate of electrolytic solution on the properties of coating was investigated. Some samples on each step were fabricated during electroplating. The results obtained from polarization measurement, observation of SEM photograph, adhesion test of coating and microhardness test are as follows. On silver plating, polarization resistance of potentiostatic cathodic polarization curve is reduced as the flow rate of Ag electrolytic solution increases. And above resistance is also reduced when the minor chemicals of sodium cyanide and sodium carbonate are added in potassium silver cyanide bath. The reduced polarization resistance makes silver deposition on the cathode easy. An increase in the current density and the coating thickness causes the particle size of deposit to coarsen, and consequently the Knoop microhardness of the coating decreases. On selective plating an increase in the flow rate of plating solution lead to do high speed plating with high current density. In this case, the surface morphology of deposit is of fine microstructure with high Knoop hardness. An increasing trend of the adhesion of coating was shown with increasing the current density and flow rate of electrolytic solution.

• 대한금속재료학회지
• /
• 제47권7호
• /
• pp.423-432
• /
• 2009

In the galvanizing coating process, the effects of the silicon content on the coatability and wettability of molten zinc were investigated on Dual-Phase High Strength Steels (DP-HSS) with various Si contents using the galvanizing simulator and dynamic reactive wetting systems. DP-HSS showed good coatability and a well-developed inhibition layer in the range of Si content below 0.5 wt%. Good coatability was the results of the mixed oxide $Mn_{2}SiO_{4}$, being formed by the selective oxidation on the surface, with a low contact angle in molten zinc and a large fraction of oxide free surface that provided a sufficient site for the molten zinc to wet and react with the substrate. On the other hand, with more than 0.5 wt%, DP-HSS exhibited poor coatability and an irregularly developed inhibition layer. The poor coatability was due to the poor wettability that resulted from the development of network-type layers of amorphous ${SiO}_{2}$, leading to a high contact angle in molten zinc, on the surface.

• 대한금속재료학회지
• /
• 제46권7호
• /
• pp.427-436
• /
• 2008

The effect of dewpoints on annealing behavior and coating characteristics such as wettability and galvannealing kinetics was studied by annealing 0.3wt%Si - 0.1~0.4wt% Mn added interstitial-free high strength steels(IF-HSS). The 0.3wt%Si-0.1wt%Mn steel exhibited good wettability with molten zinc and galvannealing kinetics after annealing when the dewpoint of $H_2-N_2$ mixed gas was above $-20^{\circ}C$. It is shown that the wettability and galvannealing kinetics are directly related to the coverage of the external(surface) oxide formed by selective oxidation during annealing. At $N_2-15%H_2$ annealing atmosphere, the increase of dewpoint results in a gradual transition from external to internal selective oxidation. The decrease of external oxidation of alloying elements with a concurrent increase of their subsurface enrichment in the substrate, showing a larger surface area that was free of oxide particles, contributed to the improved wettability and galvannealing kinetics. On the other hand, the corresponding wettability and galvannealing kinetics were deteriorated with the dewpoints below $-20^{\circ}C$. The continuous oxide layer of network and/or film type was formed on the steel surface, leading to the poor wettability and galvannealing kinetics. It causes a high contact angle between annealed surface and molten zinc and plays an interrupting role in interdiffusion of Zn and Fe during galvannealing process.

• 한국군사과학기술학회지
• /
• 제14권6호
• /
• pp.974-978
• /
• 2011

The beam-matter interaction with various coating effects has received continued attention in the high power laser community. Previous works suggest that coatings promote target damage when compared to beaming on uncoated surface. Three types of paint coatings(Acrylic urethane, Silicone alkyd and Stealth blend) and a water coat on metals(Al, Ti and STS) are irradiated with a $CO_2$ laser. Both strain and temperature measurements are provided for assessing the instantaneous response characteristics of each coating on different metals. A selective combination of surface coats with metals has proven effective in either preventing or enhancing damage, both thermal and mechanical, associated with focused beaming on a target.

• 한국태양에너지학회 논문집
• /
• 제26권1호
• /
• pp.57-64
• /
• 2006

Cr-CrO cermet solar selective coatings with a double cermets layer film structure were prepared using a special direct current (dc) magnetron sputtering technology. The typical films structures from surface to bottom substrate were measured to be an $Al_2O_3$ anti-reflection layer on a double Cr-CrO cermet layer on an Al metal infrared reflection layer. Optical properties of optimized Cr-CrO cermet solar selective coating were absorptance (${\alpha}$) = 0.95 and emittance (${\varepsilon}$) = 0.10 ($100^{\circ}C$). Atomic force microscopy (AFM) image showed that Cr-CrO cermet film was very smooth and their grain size was also very small The results of thermal stability test showed that the Cr-CrO cermet solar selective coatings were stable for use at temperature of $400^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.110-111
• /
• 2008

Diamond material were manufactured using electrical pyrolysis method and hot filament method. Surface morphology was observed with SEM and its microstructure was investigated using Raman spectroscopy. The accumulation of the particles was observed to have strong selective and to deposit at the substrate only on the roughly polished steel surface compared to the mirror polished implying that the particle was a charged.

• Corrosion Science and Technology
• /
• 제7권1호
• /
• pp.1-5
• /
• 2008

The gas atmosphere in continuous annealing and galvanizing lines alters both composition and microstructure of the surface and sub-surface of sheet steel. The formation and morphology of the oxides of alloying elements in High Strength Interstitial Free (HS-IF), Dual Phase (DP) and Transformation-Induced Plasticity (TRIP) steels are strongly influenced by the furnace dew point, and the presence of specific oxide may result in surface defects and bare areas on galvanized sheet products. The present contribution reviews the progress made recently in understanding the selective formation of surface and subsurface oxides during annealing in hot dip galvanizing and conventional continuous annealing lines. It is believed that the surface and sub-surface composition and microstructure have a pronounced influence on galvanized sheet product surface quality. In the present study, it is shown that the understanding of the relevant phenomena requires a combination of precise laboratory-scale simulations of the relevant technological processes and the use of advanced surface analytical tools.

• 한국군사과학기술학회지
• /
• 제18권4호
• /
• pp.369-375
• /
• 2015

In this paper, transparent circuit analog radar absorbing structure with angular stability for stealth aircraft canopy was proposed and designed. To obtain wideband electromagnetic absorption, optical transparency and smaller thickness, we proposed the novel FSS(Frequency Selective Surface) for X-band and implemented the resistive FSS and PEC(Perfect Electric Conductor) plane using ITO(Indium Thin Oxide) coating with optical transmissivity of 90 %. Reflection loss characteristics for different incident angles of both TE(Transverse Electric) and TM(Transverse Magnetic) polarizations are presented through simulations. We then fabricated the proposed structure to verify the simulation results. The comparisons between the simulation and measured results show good agreements. The results also show that the proposed radar absorbing structure can provide better frequency stability for different incidence angles and polarizations as well as optical transparency. We can apply this proposed structure to the canopy of stealth aircraft and other stealth applications for visible transparency.

• 한국산학기술학회논문지
• /
• 제21권4호
• /
• pp.20-25
• /
• 2020

나노과학과 나노기술의 발전에 따라 선택적 패턴 성장을 위한 기술이 주목을 받고 있다. 실리카(Silica) 나노입자는 바이오 라벨링, 바이오 이미징 및 바이오 센싱에 사용되고 있는 유망한 나노소재이다. 본 연구에서는 실리카 나노입자를 수정된 스토버 방법(Stöber Method)인 졸겔(Sol-Gel) 공정으로 합성하였다. 또한 기판의 표면을 미세접촉프린팅 기술로 발수 처리하여 실리카 나노입자를 선택적으로 패턴 성장시켰다. 합성된 실리카 나노입자의 크기와 선택적으로 패턴 성장된 실리카 나노입자의 표면형상을 전계방출 주사전자현미경(Field Emission Scanning Electron Microscopy, FE-SEM)으로 조사하였고, 기판의 표면 기능화에 따른 기판의 접촉각 특성을 조사하였다. 그 결과 OTS 용액으로 발수 처리된 기판에서는 실리카 나노입자를 스핀 코팅하였을 때, 실리카 나노입자를 관찰할 수 없었으나, KOH 용액으로 친수 처리된 기판에서는 실리카 나노입자가 잘 코팅되는 것을 확인하였다. 또한 미세접촉프린팅 기술로 발수 처리한 기판영역 외에서만 실리카 나노입자가 선택적으로 패턴 성장하는 것을 FE-SEM으로 확인하였다. 이러한 실리카 나노입자의 패턴성장 특성을 염료가 도핑 된 실리카 나노입자에 적용한다면, 실리카 나노입자의 패턴 성장 기술은 바이오 이미징 및 바이오 센싱 분야에 유용하게 활용될 것으로 기대된다.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.247-253
• /
• 2010

The characteristics of selective oxidation prior to hot-dip galvanizing with the annealing atmosphere dew point and chemical composition in dual-phase steels and their effect on the inhibition layer formation relevant to coating adhesion have been studied using a combination of electron microscopic and surface analytical techniques. The annealed and also galvanized samples of 3 kinds of Si/Mn ratios with varied amounts of Si addition were prepared by galvanizing simulator. The dew point was controlled at soaking temperature $800^{\circ}C$ in 15%$H_2$ -85%$N_2$ atmosphere. It was shown that good adhesion factors were mainly uniformity of oxide particle distribution of low number density and low Si/Mn ratio prior to hot-dip galvanizing. Their effect was the greatly reduced coating bare spots and the formation of uniform inhibition layer leading to good adhesion of Zn overlay. The mechanism of good adhesion is suggested by two processes: the formation of inhibition layer on the oxide free surface uncovered with no $SiO_2$-containing particles in particular, and the inhibition layer bridging of oxide particles. The growth of inhibition layer was enhanced markedly by the delayed reaction of Fe and Al with the increase of Si/Mn ratio.