• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.702-705
• /
• 2003

We reported the result of driving PDP's in selective erase scheme and three wall charge states. Compared to the selective write driving scheme, the selective erase scheme achieved flicker free half-ON state with much simpler driving waveforms than the selective write scheme. We believed that this improvement was possible since the cells entering the address period with enough wall charges to modulate easily with.

• Journal of Information Display
• /
• v.7 no.1
• /
• pp.30-34
• /
• 2006

A sub-field rearrangement driving method has been proposed to reduce a DFC (Dynamic False Contour) phenomenon in plasma display panels. The proposed driving method expresses 256 gray levels with 16 sub-fields, while conventional one uses only 8 sub-fields. Notwithstanding the increase in the number of sub-fields, the display time is similar to the conventional 8 sub-fields driving method by appropriate choosing selective writing and selective erasing for sub-fields.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2189-2195
• /
• 2007

In this paper, we propose a newly developed selective reset waveform of a ac PDP using the wide erase pulse technique with the control of address bias voltage. Although it is generally understood that the wide pulse erasing methode shows the narrow driving margin in an opposite discharge type ac PDP, we could obtain a moderate driving margin in a 3-electrode surface discharge type ac PDP. The obtained driving margin shows a strong dependency on the sustain voltage and the address bias voltage. The lower the sustain and the address bias voltage, the wider the driving margin. The pulse width of the proposed waveform is only $10{\mu}s$, which gives additional time to the sustain period, hence increases the brightness. The brightness and contrast ratio increase about 20% together comparing to the conventional ramp type selective reset waveform with the driving scheme of 10 subfield ADS method. The driving margin was measured with the line by line addressed pattern on the white test panel of 2inch diagonal size and the discharge gas was Ne+Xe4%, 400torr.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.35-40
• /
• 2008

In this paper, fundamental driving method and selective driving each cells of charged particle type display are described. To fabricate panel, mask patterns with cell area of $500{\mu}m{\times}500{\mu}m$ are designed. Gain of driving voltage due to increase of cell gap is observed on the basis of fundamental driving method. To selectively drive each cells of charged particle type display that is driven by passive matrix method, selective driving of charged particle type display is achieved after establishing interrelation of voltage of select cell and unselect. And than crosstalk of the driven panel is observed. It can be found that the last image is maintained without additional voltage by memory effect.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.3
• /
• pp.223-231
• /
• 2008

This paper introduces a robot called the MRINSPECT V (Multifunctional Robotic crawler for Inpipe in-SPECTion V) for the inspection of pipelines with a nominal 8-in inside diameter. Based on the mechanism of the previous model MRINSPECT IV, we developed a new MRINSPECT V by using the differential driving mechanism, so that just simply controlling the speed of each driving units helps the robot to travel effectively inside the pipelines. Furthermore, the robot uses clutches in transmitting driving power to wheels. This clutch mechanism enables MRINSPECT V to select the suitable driving method according to the shape of pipeline. In this paper, the critical points in design and construction of the proposed robot are described with the preliminary results to provide good mobility and increase the efficiency.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.407-410
• /
• 2005

For reducing DFC(Dynamic False Contour), we propose a new PDP driving method by rearrangement of sub-fields. The proposed method constructs a frame using 16 sub-fields for expressing 256 gray levels. Although the number of sub-fields increases, the display time increases compared to the conventional 8 sub-fields driving method. This increase in display time is achieved by properly using both selective writing and selective erasing for each sub-field.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.1004-1008
• /
• 2012

The effect of address discharge characteristics by selective reset method is investigated to prevent the weakness of address discharge in the middle of a TV-field without increase of the black luminance. To reduce black luminance in AC PDP usually, the first subfield during one TV frame adopted the conventional rising ramp-reset waveform, whereas the other subfields adopted the subsidiary reset waveform without rising ramp type. As the wall charge for the address discharge was accumulated by only the rising ramp waveform during the first reset period, the wall charge on three electrodes was disappeared as time passed and the address discharge would be weakened in the rear subfields. To prevent a reduction of the address discharge characteristics without decrease the black luminance, the modified rising ramp reset waveform was adopted only in the sixth subfield. As a result, a modified driving method could improve the address discharge characteristics compared with selective reset driving scheme with almost the same black luminance.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.2
• /
• pp.85-90
• /
• 2021

A ADAS(Advanced Driver Assistance System) for the safe driving is an important area in autonumous car. Specially, a ADAS software using an image sensors attached in previous car is low in building cost, and utilizes for various purpose. A algorithm for detecting the break-lamp from the tail-lamp of preceding vehicle is proposed in this paper. This method can perceive the driving condition of preceding vehicle. Proposed method uses the YOLO techinicque that has a excellent performance in object tracing from real scene, and extracts the intensity variable region of break-lamp from HSV image of detected vehicle ROI(Region Of Interest). After detecting the candidate region of break-lamp, each isolated region is labeled. The break-lamp region is detected finally by using the proposed selective-attention model that percieves the shape-similarity of labeled candidate region. In order to evaluate the performance of the preceding vehicle break-lamp detection system implemented in this paper, we applied our system to the various driving images. As a results, implemented system showed successful results.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.258-260
• /
• 2003

In this paper, we study the reduction of the Dynamic False Contour in a new driving method. This method divides scan lines into Multi Blocks, and drives both selective write and selective erase address. Because of the characteristic of proposed waveform, each scan line has a different sustain pulse weight. Therefore, the Dynamic False Contour occurs seriously in the boundary of each Block. Finally, if scan-lines tie several lines, the Dynamic False Contour can reduce in the boundary of each Block.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.225-227
• /
• 2000

LGE developed and demonstrated the first 60-inch full color AC plasma display panel with the 1365 ${\times}$ 768 resolution. Both Sol-gel and E-beam method have been tried for MgO layer, and photolithography has been used for electrodes and phosphor layer to fabricate a 60-inch panel. Selective Erase, Selective Write, Address Display Separate, and Address While Display driving scheme have been tested. Its luminance and contrast ratio is about $550\;cd/m^2$ and 500:1, respectively.