• 한국산림과학회지
• /
• 제81권1호
• /
• pp.21-29
• /
• 1992

본(本) 연구(硏究)는 강원도(江原道) 인제군 기린면 진동리 소재(所在) 천연(天然) 혼효임분(混淆林分)의 구조(構造) 파악(把握)을 통하여 작업종(作業種) 결정(決定)을 위한 기초자료(基礎資料)를 제공(提供)하기 위하여 실행(實行)되었다 이를 위하여 대상(對象) 임분(林分)의 직경(直徑), 분포(分布), 수고(樹高) 분포(分布), 그리고 경급별(徑級別) 재적(材積) 분포(分布)가 분석(分析)되었고 이를 이용(利用)하여 택벌임(擇伐林)의 가능성(可能性)이 검토(檢討)되었다. 1. 직경(直徑) 분포(分布)는 전형적(典型的)인 택벌임(擇伐林)에서 볼 수 있는 지수감소형(指數減少型) 구조(構造)를 나타냈고 수고(樹高) 분포(分布)에서도 택벌림(擇伐林)으로 유도(誘導)될 수 있는 높은 가능성(可能性)을 보였는데 이는 이 대상(對象) 임분(林分)이 자생(自生) 천연림(天然林) 특유(特有)의 복층림(複層林) 구조(構造)를 소유(所有)하고 있기 때문이다. 그러나 경급별(徑級別) 재적(材積) 분포(分布)에서는 택벌(擇伐) 임형(林型)에 이르지 못한 미성숙(未成熟) 구조(構造)를 보이고 있는데 그 이유(理由)는 30cm 이상(以上)의 경급(徑級)에서의 본수(本數)의 부족(不足)에 기인(起因)한 것으로 판단(判斷)된다. 이러한 구조상(構造上)의 부확실성(不確實性)은 앞으로의 연구에서 밝혀져야 하는데 특(特)히 직경(直徑)과 재적(材積) 생장율(生長率)의 추정(推定)에 의한 미래(未來) 임분(林分) 구조(構造)의 파악(把握)이 시급(時急)한 것으로 보인다.

• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.97-103
• /
• 2001

This paper has focused on the Optimization of the cutting parameters for urning operation based on the Taguchi method. Four cutting parameters. nemely, cutting speed, feed depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using signal-to-noise(S/N) ratio and analy-sis of variance(ANOVA). The experiments have been performed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.38-42
• /
• 2001

In the machining of glass fiber reinforced plastics(GFRP), turning has been often used. But the most of past studies have been interested in the effect of fiber orientation on tool wear. In this study, the effects of fiber contents and cutting speeds on tool wear, cutting force and surface roughness are investigated experimentally. By proper selection of cutting tool, the variables are cutting speed, fiber contents and cutting length with fixed feed rate and depth of cut. The fiber contents have major effects on coated tool wear which observed as abrasive wear type.

• 한국시뮬레이션학회:학술대회논문집
• /
• 한국시뮬레이션학회 2001년도 The Seoul International Simulation Conference
• /
• pp.288-294
• /
• 2001

Present CAM technology cannot provide important physical property such as cutting farce and machined surface. Thus, the selection of cutting conditions still depends on the experience of an expert or on the machining data handbook in spite of the developed CAM technology. This paper presents an advanced methodology to help the worker to determine optimum cutting condition for CHC machining that excludes the need for expertise of machining data handbook. The virtual machining system presented in this paper can simulate the real machining states such as cutting farce and machined surface error. And virtual machining system can schedule feed rate to adjust the cutting force to the reference force.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.20-24
• /
• 2012

The objective of this study is to investigate proper cutting conditions of cellulose acetate(CA) for eyewear frames. Various cutting experiments with variation of spindle speeds and feed rates are conducted to evaluate the machinability of CA. The machinability of CA materials were discussed in terms of the cutting forces, surface roughnesses and chip formations. The cutting conditions of high spindle speeds and the feed per tooth of less than 0.05mm are recommended considering the surface roughnesses and chip formations. Also, the correlation between the surface roughness and the chip formation is investigated. These results are able to be applied to design the high-speed machine tool of CA frame.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.242-248
• /
• 2000

This paper has focused on the optimization of the cutting parameters for turning operation based on the Taguchi method. Four cutting parameters, namely, cutting speed, feed, depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using the signal-to-noise (S/N) ratio, analysis of variance (ANOVA). The experiments have been peformed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.135-144
• /
• 1998

High speed machining is a key issue in die and mold manufacturing recently. Even though this technology has great potential of high productivity. tool wear accelerated by high cutting speed to the hardened materials is other barrier. In this research, we attempted to reduce tool wear by considering tool inclination angle between tool and workpiece. The boundary lines describing machined sculptured surfaces were represented by both of cutting envelop condition and the geometric relationship of successive tool paths. Chip cross section, and cutting length could be obtained from the calculated cutting edge and the rotational engagement angle. From the simulation results, machining inclination angle of tool of $15^\circ$ was good enough from the point of tool wear and cutting force, and this value was verified through the cutting experiment of high speed ball end milling.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.114-120
• /
• 2010

Optimization of the turning process has been concentrated on the selection of the optimal cutting parameters, such as cutting speed, feed rate and depth of cut. However, optimization of the cutting parameters does not necessarily guarantee the maximum profit. For the maximization of the profit, parameters other than cutting parameters have to be taken care of. In this study, 8 price-related parameters were considered to maximize the profit of the product. Regression equations obtained from RSM technique to relate the cutting parameters and maximum cutting volume with a given insert were used. The experiments with four combinations of cutting inserts and material were executed to compare the results that made the profit and cutting volume maximized. The results showed that the cutting parameters for volume and profit maximization were totally different. Contrary to our intuition, global optimization was achieved when the number of inserts change was larger than those for volume maximization. It is attributed to the faster cutting velocity, which decreases processing time and increasing the number of tool used and the total tool changing time.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1173-1182
• /
• 2001

Recent noticeable advances of CNC machine tools have considerably improved productivity and precision in manufacturing processes. However, in the respect of productivity some defects still remain because selection of machining conditions entirely depends on the experiences of programmers. Usually, machining conditions such as feed rate and spindle speed have been selected conservatively by considering the worst cases, and it has brought the loss of machining efficiency. Thus, the improvement of cutting force controller has been done to regulate cutting force constantly and to maximize feedrate simultaneously in case that machining conditions change variously. In this study, sliding mode control with boundary layer is applied to milling process for cutting force regulation and in a commercial CNC machining center data transfer between PC and PMC (programmable machine controller) of CNC machine is done using a standard interface method. And in the cutting force measurement, an indirect cutting force measuring system using current signal of AC servo is adopted in order not to use high-priced equipment like tool dynamometer. The purpose of this study is to maximize the productivity in milling process, thus its results can be applied to cases such as rough cutting process.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.40-46
• /
• 2013

When impeller machining needs to be machined over a length in order to avoid interference with neighboring surfaces between material and tool, there are no databases about cutting condition according to tool slenderness ratio. So selection and machining of cutting condition depends on expert's experience. Therefore, the purpose of this paper is deciding cutting condition in roughing and finishing process of impeller according to slenderness ratio of AL7075's end-mill that is the most commonly used for impeller. We have tested for about relation between Slenderness ration and fluctuation width of the cutting force, surface roughness and depth of cut ratio to observe cutting characteristics according to slenderness ratio. The experiments of cutting characteristics and processing criteria are compared with AL5052 which is existing information.