• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.365-368
• /
• 2001

This paper described a design and implementation of the division/square-root for a redundant floating point binary number using high-speed quotient selector. This division/square-root used the method of a redundant binary addition with 25MHz clock speed. The addition of two numbers can be performed in a constant time independent of the word length since carry propagation can be eliminated. We have developed a 16-bit VLSI circuit for division and square-root operations used extensively in each iterative step. It peformed the division and square-root by a redundant binary addition to the shifted binary number every 16 cycles. Also the circuit uses the nonrestoring method to obtain a quotient. The quotient selection logic used a leading three digits of partial remainders in order to be implemented in a simple circuit. As a result, the performance of the proposed scheme is further enhanced in the speed of operation process by applying new quotient selection addition logic which can be parallelly process the quotient decision field. It showed the speed-up of 13% faster than previously presented schemes used the same algorithms.

• ETRI Journal
• /
• 제24권6호
• /
• pp.462-464
• /
• 2002

This paper presents a serial interface circuit that permits selection of the amount of data converted from serial-to-parallel and parallel-to-serial and overcomes the disadvantages of the conventional serial input/output interface. Based on the selected data length operating mode, 8 bit or 16 bit serial-to-parallel and 8 bit or 16 bit parallel-to-serial conversion takes place in data blocks of the selected data length.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.264-266
• /
• 2001

We must consider resistance capacitance and their circuit connection condition for cable charging current test by IEC60265-1. According to their values and circuits, the ratio of applied voltage and transient recovery voltage are much different. This paper is convinced of TRV waves and proposes the optical circuit required at the standard via the simulation of all circuit conditions.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1992년도 학술논문발표회 논문집 제11권 1호
• /
• pp.107-110
• /
• 1992

We investigate the influence of individual properties of piezoceramics such as elastic, dielectric, piezoelectric constants, and the coupling factor on the performance of the transducer operating in thickness mode oscillation. The investigation employs equivalent circuit analysis techniques. Appropriate transfer functions are obtained and discussed which suggest optimum selection guides of piezoelectric ceramics for each purpose, i.e. a transmitter, a receiver, and a pulse-echo transducer. The guides can help ceramic scientists find the direction to proceed in new material development.

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 2000년도 봄 학술발표논문집 Vol.27 No.1 (A)
• /
• pp.36-38
• /
• 2000

An optoelectronic database filter chip for high performance database computers and applications is proposed. The proposed device is designed to perform the selection and projection operations of relational database operation on-the-fly in page-parallel manner to increase the overall performance of a database system. The device utilizes CMOS smart pixel array consists of detector and combinational logic circuit to perform the selection and projection operation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1853-1859
• /
• 2008

IGBT modules are designed for low loss, rugged for all environments and user friendly. Low on state saturation voltage with high switching speed is the primary concerns. In this paper selection of IGBT, module ratings and characteristics are discussed. The IGBT design topic of protection against over voltage and over current are covered. Emphasis on turn off switching, short circuit switching and necessary precautions are dealt. Selection of IGBT device, gate drive power, and its lay out considerations are covered in detail.

• ETRI Journal
• /
• 제33권6호
• /
• pp.904-913
• /
• 2011

Three-dimensional (3D) memories using through-silicon vias (TSVs) as vertical buses across memory layers will likely be the first commercial application of 3D integrated circuit technology. The memory dies to stack together in a 3D memory are selected by a die-selection method. The conventional die-selection methods do not result in a high-enough yields of 3D memories because 3D memories are typically composed of known-good-dies (KGDs), which are repaired using self-contained redundancies. In 3D memory, redundancy sharing between neighboring vertical memory dies using TSVs is an effective strategy for yield enhancement. With the redundancy sharing strategy, a known-bad-die (KBD) possibly becomes a KGD after bonding. In this paper, we propose a novel die-selection method using KBDs as well as KGDs for yield enhancement in 3D memory. The proposed die-selection method uses three search-space conditions, which can reduce the search space for selecting memory dies to manufacture 3D memories. Simulation results show that the proposed die-selection method can significantly improve the yield of 3D memories in various fault distributions.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2485-2492
• /
• 2018

The rapid development of large-scale integrated circuits has brought great challenges to the circuit testing and diagnosis, and due to the lack of exact fault models, inaccurate analog components tolerance, and some nonlinear factors, the analog circuit fault diagnosis is still regarded as an extremely difficult problem. To cope with the problem that it's difficult to extract fault features effectively from masses of original data of the nonlinear continuous analog circuit output signal, a novel approach of feature extraction and dimension reduction for analog circuit fault diagnosis based on wavelet packet decomposition, local linear embedding algorithm, and clone selection algorithm (WPD-LLE-CSA) is proposed. The proposed method can identify faulty components in complicated analog circuits with a high accuracy above 99%. Compared with the existing feature extraction methods, the proposed method can significantly reduce the quantity of features with less time spent under the premise of maintaining a high level of diagnosing rate, and also the ratio of dimensionality reduction was discussed. Several groups of experiments are conducted to demonstrate the efficiency of the proposed method.

• 대한산업공학회지
• /
• 제20권4호
• /
• pp.5-21
• /
• 1994

We have described the optimal process route selection model for the PCB(printed circuit board) auto-insertion line. This PCB assembly line is known as a FFL(flexible flow line) which produces a range of products keeping the flow shop properties. Under FFL environments, we have emphasized the balancing of work-loads in order to maximize total productivity of PCB auto-insertion line. So we have developed a heuristic algorithm based on a work-order selection rule and min-max concept for the job route selection model.

• 전자공학회논문지
• /
• 제54권6호
• /
• pp.55-64
• /
• 2017

대용량 고화질의 영상 응용분야에서는 많은 양의 데이터를 고속으로 처리하는 기술이 필요하며, 이를 위해 고속화된 병렬처리 시스템이 요구된다. 2004년 park은 병렬처리 메모리의 충돌 없이 여러 처리기에 데이터를 접속할 수 있는 방법을 제안하였다. 제안된 MAMS(Multi-Access Memory System) 는 이후 MAMS-PP16 및 MAMS-PP64 등으로 추가적인 연구가 이루어졌다. MAMS는 병렬처리를 위한 메모리 아키텍처로써 One-chip으로 구성되어야하기 때문에 기존 MAMS와 동일한 기능을 수행하면서 아키텍처의 최소화 하는 방법의 연구가 필요하다. 주소 계산 (ACR : Address Calculation and Routing) circuit과 MMS(Memory Module Selection)circuit의 아키텍처는 메모리에 있는 데이터를 병렬처리기(Prossing Elements)들에게 전달한다. 본 논문에서는 MMS circuit을 사용하지 않고 ACR circuit 내부에 1개의 쉬프트와 메모리 모듈의 개수만큼의 조건문으로 구성하는 방법을 통해 아키텍처를 최소화 하는 방법을 제안한다. 구현한 아키텍처의 검증을 위해 Image correlation 실험을 하였다. 실험을 통하여 제안된 MAMS-PP64의 처리시간을 측정 하였으며, 그 결과 Ratio가 평균 1.05향상 된 결과를 확인 할 수 있었다.