• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1148-1158
• /
• 2005

This work reports results of our study on the dynamic responses of the buried pipelines both along the axial and the transverse directions under various boundary end conditions. We have considered three cases, i.e., the free ends, the fixed ends, and the fixed-free ends. We have studied the seismic responses of the buried pipelines with the various boundary end conditions both along the axial and the transverse direction. We have considered three cases, i.e., the free ends, the fixed ends, and the fixed-free ends for the axial direction, and three more cases including the guided ends, the simply supported ends, and the supported-guided ends for the transverse direction. The buried pipelines are modeled as beams on elastic foundation while the seismic waves as a ground displacement in the form of a sinusoidal wave. The natural frequency and its mode, and the effect of parameters have been interpreted in terms of free vibration. The natural frequency varies most significantly by the soil stiffness and the length of the buried pipelines in the case of free vibration, which increases with increasing soil stiffness and decreases with increasing length of the buried pipeline. Such a behavior appears most prominently along the axial rather than the transverse direction of the buried pipelines. The resulting frequencies and the mode shapes obtained from the free vibration for the various boundary end conditions of the pipelines have been utilized to derive the mathematical formulae for the displacements and the strains along the axial direction, and the displacements and the bending strains along the transverse direction in case of the forced vibration. The negligibly small difference of 6.2% between our result and that of Ogawa et. al. (2001) for the axial strain with a one second period confirms the accuracy of our approach in this study.

• Earthquakes and Structures
• /
• 제7권5호
• /
• pp.843-859
• /
• 2014

In the present study, the seismic performance of structural walls with boundary elements confined by conventional tie hoops and steel fiber concrete (SFC) was investigated. Cyclic lateral loading tests on four wall specimens under constant axial load were performed. The primary test parameters considered were the spacing of boundary element transverse reinforcement and the use of steel fiber concrete. Test results showed that the wall specimen with boundary elements complying with ACI 318-11 21.9.6 failed at a high drift ratio of 4.5% due to concrete crushing and re-bar buckling. For the specimens where SFC was selectively used in the plastic hinge region, the spalling and crushing of concrete were substantially alleviated. However, sliding shear failure occurred at the interface of SFC and plain concrete at a moderate drift ratio of 3.0% as tensile plastic strains of longitudinal bars were accumulated during cyclic loading. The behaviors of wall specimens were examined through nonlinear section analysis adopting the stress-strain relationships of confined concrete and SFC.

• Earthquakes and Structures
• /
• 제18권2호
• /
• pp.201-213
• /
• 2020

Seismic damages that occurred by the effects of epicenter distance of the earthquake are one of the most important problems for the earthquake engineering. In this study, it is aimed to examine the nonlinear seismic behaviors of concrete gravity (CG) dams considering various epicenter distances. For this purpose, Boyabat CG dam that is one of the biggest concrete gravity dams in Turkey is selected as a numerical application. FLAC3D software based on finite difference method is used for modelling and analyzing of the dam. Drucker-Prager nonlinear material model is used for the concrete body and Mohr-Coulomb nonlinear material model is taken into account for the foundation. Special interface elements are used between dam body and foundation to represent interaction condition. Free-field and quiet non-reflecting boundary conditions are utilized for the main surfaces of 3D model. Total 5 various epicenter distances of 1989 Loma Prieta earthquake are considered in 3D earthquake analyses and these distances are 5 km, 11 km, 24 km, 85 km and 93 km, respectively. According to 3D seismic results, x-y-z displacements, principal stresses and shear strain failures of the dam are evaluated in detail. It is clearly seen from this study that the nonlinear seismic behaviors of the CG dams change depending to epicenter distance of the earthquake. Thus, it is clearly recommended in this study that when a CG dam is modelled or analyzed, distance of the earthquake fault to the dam should be strongly examined in detail. Otherwise, earthquake damages can be occurred in the concrete dam body by the effects of seismic loads.

• Structural Engineering and Mechanics
• /
• 제57권3호
• /
• pp.569-585
• /
• 2016

This paper highlights a case study that investigates the behaviour of existing bridge, West Terrace Bridge, induced by horizontal seismic loading. Unfortunately the lack of past information related to seismic activity within the NSW region has made it difficult to understand better the capacity of the structure if Earthquake occurs. The research was conducted through the University of Western Sydney in conjunction with Railcorp Australia, as part of disaster reduction preparedness program. The focus of seismic analyses was on the assessment of stress behaviour, induced by cyclic horizontal/vertical displacements, within the concrete slab and steel truss of the bridge under various Earthquake Year Return Intervals (YRI) of 1-100, 1-200, 1-250, 1-500, 1-800, 1-1000, 1-1500, 1-2000 and 1-2500. Furthermore the stresses and displacements were rigorously analysed through a parametric study conducted using different boundary conditions. The numerical analysis of the concrete slab and steel truss were performed through the finite element software, ABAQUS. The field measurements and observation had been used to validate the results drawn from the finite element simulation. It was illustrated that under a YRI of 1/1000 the bottom chord of the steel truss failed as the stress induced surpassed the ultimate stress capacity and the horizontal displacement exceeded the allowable displacement measured in the field observations whereas the vertical displacement remained within the previously observed limitations. Furthermore the parametric studies in this paper demonstrate that a change in boundary conditions alleviated the stress distribution throughout the structure allowing it to withstand a greater load induced by the earthquake YRI but ultimately failed when the maximum earthquake loading was applied. Therefore it was recommended to provide a gap of 50mm on the end of the concrete slab to allow the structure to displace without increasing the stress in the structure. Finally, this study has proposed a design chart to showcase the failure mode of the bridge when subjected to seismic loading.

• 지질공학
• /
• 제33권2호
• /
• pp.293-305
• /
• 2023

지진이 발생할 때 대한 지진동 증폭 현상을 확인하기 위해 1g 진동대와 연성토조(Laminar Shear Box, LSB)를 이용하여 모형지반을 조성하였고, 3가지 모델에 대하여 지진동 증폭현상에 대하여 확인하였다. 3가지의 모형지반을 선정하였으며 모든 모형지반에서 조밀한 층과 느슨한 층으로 나누었고, 지반모형의 경우는 다층 수평지반, 다층 제방지반, 다층 분지지반모형으로 선정하였다. 각 지반모형을 제작하며 가속도계 매설을 진행하였으며, 인공지진파, Sinesweep파와 Sine 10 Hz의 지진파를 통하여 증폭현상을 확인하였다. 최대지반가속도(Peak ground acclelration, PGA)와 응답스펙트럼 가속도(Spectrum acceleration, SA)를 통해 지진동 증폭현상을 확인하였다. 수평 다층지반에서 조밀한 지반을 통과 후 느슨한 지반에서 가속도 증폭이 조밀한 지반에 비해 크게 발생하는 것을 확인할 수 있었으며, 다른 두 모형지반에서는 층의 경계면을 통과 후 점차 중심부에서 가속도 증폭이 더 크게 발생하는 것을 확인할 수 있었다.

• 한국지진공학회논문집
• /
• 제17권1호
• /
• pp.43-51
• /
• 2013

In this paper, analytical models for reinforced concrete shear wall systems designed based on Korean Building Code (KBC2009) are proposed, which have special and semi-special seismic details and are compared with experimental results for a verification of analytical models. In addition, semi-special seismic details aimed to improve constructability and enhance economic efficiency were proposed and evaluated. The analytical models were performed based on nonlinear static and dynamic analysis. Through the nonlinear analyses, two seismic details showed the similar seismic behavior from the cyclic test and the analytical models for the two different seismic details represented the behavior in terms of the initial stiffness, maximum strength and strength degradation. And newly proposed seismic details(semi-special) provided with similar hysterestic behavior as well as the maximum drift.

• 대한건축학회논문집:구조계
• /
• 제36권1호
• /
• pp.137-146
• /
• 2020

In this study, various application schemes of seismic isolation system which can be applied to Hanok have been studied by analyzing its structural characteristics under seismic load. Structural stability of Hanok is more required against seismic load as Hanok becomes long-spanned and multi-storied. To meet this goal, it becomes necessary to study more advanced technology such as seismic isolation design as well as seismic control design and seismic resistant design suitable to Hanok. Seismic isolation systems have been successfully applied to RC and steel structures to improve structural performance during earthquakes. Based on these previous study, we proposed four application schemes of seismic isolation design suitable for Hanok and analyzed their structural characteristics and applicability to Hanok in conceptual level based on its structural characteristics. The proposed four schemes are base isolation method, ground isolation method, roof isolation method and intermediate-story isolation method. The applicability of the proposed method was evaluated by performing boundary nonlinear dynamic analysis to the typical Hanok for the two types of isolation method, that is, ground isolation method and roof isolation method, and the results showed that the proposed methods produced good performance enough to be applied to Hanok.

• 토지주택연구
• /
• 제7권1호
• /
• pp.31-41
• /
• 2016

이 논문은 최근 천영수 등(2011)에 의하여 제안된 벽체 단부 횡보강상세를 지닌 벽체를 중심으로 벽체의 구조성능 영향 변수들을 대상으로 한 실험결과와 그에 따른 내진거동 및 이력특성을 제시하고 있다. 제시된 결과는 동 벽체의 비선형이력특성을 규명함으로써 향후 성능기반설계의 적용을 위한 기초자료를 제공하게 될 것이다. 실험결과, 제안된 횡보강 상세를 채용한 실험체의 균열 및 파괴 양상은 축력과 내진철근의 적용 여부와 상관없이 유사한 경향을 나타내었으며, 기준에서 제시하고 있는 설계식에 의하여 실험체의 최대강도를 잘 예측할 수 있는 것으로 나타났다. 또한, 축력이 높을 수록 초기강성과 최대강도는 증가하나 변형능력은 떨어지는 경향이 있어 고 축력으로 인한 변형능력 감소에 대한 고려가 필요할 것으로 보이며, 고 축력이 작용하는 벽체의 경우 내진철근의 사용이 변형능력의 확보라는 관점에서 매우 효과적인 방안이 될 것으로 보임으로 가능하다면 소성힌지 영역은 내진철근을 사용한 경계요소로 보강하는 것이 바람직한 것으로 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권1호
• /
• pp.56-63
• /
• 2018

이 연구에서는 연성중심의 보강을 위하여 벽체의 양단부에서 경계요소를 형성하는 내진 보강공법이 적용된 벽체의 반복 휨 거동을 평가하였다. 벽체 경계요소에서 구속효과를 위한 횡보강은 프리스트레스트 와이어로프를 사용하였다. 주요 변수는 제시된 단면 확대공법의 보강 높이로 하였다. 최소 보강 높이는 보강 벽체와 기존 벽체의 모멘트 분포의 비교로부터 결정하였다. 실험결과, 제시된 보강방법은 벽체의 휨 강성 및 연성향상에 매우 효율적이었는데, 최대내력 시 강성과 최대내력의 80%지점에서 산정한 일손상지수는 무보강 벽체에 비해 각각 평균 46%와 210% 증가하였다. 보강높이가 벽체의 일손상지수 증가에 미치는 영향은 보강높이가 $2.0l_w$ 이상일 때 중요하지 않았다. 보강된 벽체의 휨 내력은 ACI 318-14에서 제안하는 등가응력블록을 통한 예측 값보다 22% 이상 높았다.

• 지구물리
• /
• 제9권4호
• /
• pp.351-359
• /
• 2006

We investigated subsurface structures of the Bransfield Basin, the Antarctic with AUH (Autonomous Underwater Hydrophne) which was designed to record abyssal T-waves generated from submarine earthquakes. The data obtained from a multi-channel seismic survey and an AUH were used for this study. A seismic reflection method was applied to the multi-channel seismic survey data in order to identify bathymetry and sedimentary structures, and the signals recorded in the AUH were used to obtain deep structures as we applied a seismic refraction method. Even though we couldn’t investigate deeper and detailed structure in study area because of lack of Airgun’s capacity, the AUH showed possibilities for being used for a marine seismic survey. From this experiment, we decided the upper and lower sediment layer velocities, detected irregular basement topography probably caused by submarine volcanic/magmatic activities, and retrieved the velocity of the basement and the depth of the sediment layer/basement boundary.